Ethernet Buccaneer Environmentally Sealed Connectors IMPORTANT - PLEASE READ INSTRUCTIONS PRIOR TO ASSEMBLY Before using the connector, it is important that these instructions are carefully read and understood to ensure the connector system is completely water tight and performs to specification. Cable Glands To ensure the correct cable sealing, cable glands are supplied to accurately fit cable diameters from 3.5 to 8.0mm. It is important to choose the closest gland size to the cable being used. Cable diameter 3.5 - 5mm 5 - 7mm 6 - 8mm Gland Colour Blue Green Red The standard shielded RJ45, as supplied, is suitable for cables up to 6.0mm diameter, larger cables may require different assembly techniques. CONNECTOR COMPONENTS Carrier Moulding RJ45 Plug Load Bar Cable Locking Ring Gland Gland Cage Gland Nut Connector Body ASSEMBLY/WIRING INSTRUCTIONS 1. Thread the gland nut, gland cage, gland and connector body on to the cable. 5. Crop the latching clip on the RJ45 ensuring this is completely removed. 25.4mm (1.00”) 2. Remove the cable jacket carefully taking care not to damage the braid and foil. Fold back the braid and foil over the cable jacket. 6. Push the RJ45 into the carrier moulding until it latches. 3. Un-twist the conductors and feed through the appropriate hole in the load bar, according to the wiring standard required. Push the loading bar fully home on to cable. Trim conductors to extend 8.64mm (0.34”) out of the front of the load bar. 2 4 6 8 Loading bar viewed from rear, wire entry side. Wiring Configuration 568-A Position White/Green Green White/Orange Blue White/Blue Orange White/Brown Brown 1 2 3 4 5 6 7 8 568-B White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown 7. Pull up the connector body and locate the carrier. The carrier sits into a ‘D’ shape aperture in the connector body, ensure it is seated correctly. Locate locking ring and tighten ring to retain insert, using the assembly tool provided. 1 3 5 7 1 Front face view Load Bar 8.64mm (0.34”) 4. Push load bar and cable fully home into RJ45, ensuring the braid and foil are in contact with the metal shell. Crimp RJ45 with appropriate crimp tool and die set. Trim back braid and foil flush with rear of RJ45 body. 8. Slide gland, gland cage and gland nut up to body moulding then tighten to torque of 1.5-2.0lb/ins, 13-18Nm. For the PX0834/A version fully tighten nut until end of travel. Note: Over tightening of gland nut may constrict cable and could cause signal distortion. Ethernet Buccaneer Environmentally Sealed Connectors TECHNICAL SPECIFICATION FOR ETHERNET BUCCANEER CONNECTOR SYSTEM Stranded S-FTP Patch cord cable - PUR Jacket Re-wireable and Panel mounted connectors Construction Polyurethane (PUR) Jacket Sealing Conductors 24AWG (7/0.2mm) bare copper Insulation HD-PE Mechanical Pair twisted 2 of the above cores IP68, EN60529 IP69, DIN 40050.9 Materials Connector Body Polyester Flammability rating UL94V-0 4 of the above cores ‘O’ rings Silicon Tape 1 lap mylar tape Panel Gasket Silicon Screen 1 layer mylar and aluminium tape, tape, 0.12mm tinned copper braid Operating Temperature –20˚C to +70˚C RoHS Compliant Core Sheath PUR Jacket Black Op Temperature –25°C to +85°C Min. bend radius 10 x o/d (installation) Min. bend radius 6 x o/d (installed) Diameter 6.1mm nominal Electrical @ 20˚C RJ45 Plug Materials Moulding Polycarbonate Flammability UL94V-0 Contact material Phosphor Bronze Contact plating 50 micron gold Operating Temperature –40°C to +70°C Mating cycles 1,000 cycles Characteristic Impedance 100Ω ±15Ω @ 100MHz Capacitance 330pF/km Conductor Loop resistance 29Ω/100m maximum No. Conductors 8 Skew 45 nsec/100m @ 100MHz Current rating 1.5A TIA/EIA Rating Cat 5e Voltage rating 30V ac, 42V dc Electrical Contact resistance 10mΩ max. Performance Cat 5e RoHS Compliant RJ45 Coupler Materials Ethernet Buccaneer IP68 & IP69K Waterproof Ethernet Connectors Coupler Shell Copper Alloy Coupler Plating Nickel Moulding ABS Flammability UL94V-0 Contact material Phosphor Bronze Contact plating 50 micron gold Operating Temperature –40°C to +70°C Mating cycles 1,000 cycles Electrical Wiring and Assembly Instructions for PX0834/A and PX0834/B No. Conductors 8 Current rating 1.5A Voltage rating 30V ac, 42V dc Contact resistance 10mΩ max. Performance Cat 5e RoHS Compliant Part no: 14153 iss 6 bulgin bulgin.com a brand of Elektron Technology