POWER SPLITTER – High Precision Power Chip Divider HOW TO ORDER PPS -10 50R0 M LF Terminal Material SnPb = Leave Blank Lead Free = LF Packaging M = tape/reel 5,000 pcs O = Bulk Impedance 50Ω Size 0805 = 10 0603 = 16 FEATURES High Frequency Splitter is constructed of thin film resistive material 1206 = 18 Series Precision Power Splitter Power splitter with excellent high frequency characteristics for applications from DC~20GHz This product has a small reflection feature, allowing for superior in high frequency applications Allows for high density mounting Bit error is restrained by keeping high frequency digital signal stable PPS-A ELECTRICAL CHARACTERISTICS Item Size Circuit Configuration Operating Frequency 6 ± 0.5dB Insertion Loss 6 ± 1.0dB Split Deviation 1.3 VSWR 1.5 Input Power at 70°C Max Overload Power Resistance Operating Temperature Packaging PPS-16 2/25 0603 2/25 DC~20GHz DC~10GHz 10~20GHz 0.3dB max DC~10GHz 10~20GHz 100mW 200mW PPS-10 0805 2/25 DC~17.5GHz DC~10GHz 10~17.5GHz 0.3dB max DC~10GHz 10~17.5GHz 125mW 250mW R1 = R2 = R3 = 50Ω typical -40°C ~ +125°C 1,000/Reel or 5,000/Reel PPS-18 2/25 1206 2/25 DC~15GHz DC~10GHz 10~15GHz 0.3dB max DC~10GHz 10~15GHz 250mW 500mW DERATING CURVE – Circuit 2/25 American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 1 POWER SPLITTER – High Precision Power Chip Divider DIMENSIONS (mm) Series L W a b t PPS-05 2/25 1.00 ± 0.2 0.50 ± 0.2 0.4 ± 0.1 0.30 ± 0.1 0.4 ± 0.10 PPS-16 2/25 1.60 ± 0.2 0.80 ± 0.2 0.4 ± 0.1 0.30 ± 0.1 0.4 ± 0.10 PPS-10 2/25 2.00 ± 0.2 1.25±0.2 0.4 ± 0.1 0.30 ± 0.1 0.4 ± 0.10 PPS-18 2/25 3.20 ± 0.2 1.60 ± 0.2 0.3 ± 0.1 0.35 ± 0.1 0.4 ± 0.10 PPS-12 2/25 5.00 ± 0.2 2.5 ± 0.2 0.35 ± 0.1 0.65 ± 0.1 0.8 ± 0.15 SCHEMATIC LEGEND 1. 2. 3. 4. 5. SCHEMATIC – Circuit 2/25 Thin Film Resistor Overcoat Resin Terminal (SnPb or Lead Free) Marking (dot to indicate direction & bar) Alumina Substrate PERFORMANCE Item Test Condition Tolerance Short Time Overload 2.5 times of the rated voltage shall be applied for 5 seconds. ±0.1% Rated Load Life Apply rated voltage for 90 min followed by a pause of 30 min at 70±3°C for 1000 hours. ±0.25% Moisture Load Life The chip divider is applied rated voltage for 90 min at 60±2°C 90～95%RH for 1000 hours. ±0.25% Temperature Cycle [-55°C (30min)-R.T.(3min)-+125°C(30min)-R.T.(3min)] is repeated 5 cycles. ±0.1% Soldering Heat Resistance Leave NR in melt solder of 260±5°C for 10±1 seconds. ±0.1% Strength Between Terminals Distance between fulcrums : 90mm; Bending width : 3mm; Substrate: Glass epoxy t=1.6mm Solderability Leave NR in melted solder of 235±5°C for 3±0.5 seconds. Insulation Resistance A minute after 500 DC ±0.1% ≥95% of the surface should be wet ≥ 1000M Ω The content of this specification may change without notification 10/23/08 American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 2