Available at Digi-Key**
www.digikey.com
Stratum 3E High Stability
Oven Stabilized Oscillator
OH200-Series
OCXO / VCOCXO
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Connor-Winfield’s high stability OH200series are exceptionally precise frequency
standards, excellent for use in cellular base
stations, test equipment, Synchronous
Ethernet, VSAT and Stratum 3E applications
These unique OCXO / VCOCXO oscillator
products provide temperature stabilities
in the range of ±3 ppb to ±25 ppb, over
the commercial, extended commercial or
the industrial temperature range. Power
requirements are 3W over the commercial
temperature range and 4.5W over the
industrial temperature range. Additionally,
excellent aging is achieved through the use
of overtone SC cut crystals.
The OH200 series is available with
CMOS logic or Sinewave output along with
Voltage Controlled option. These oscillators
provide outstanding phase noise that varies
depending on frequency. Frequencies are
available from 5.0 to 40.0 MHz. Allan Variance
specifications are rated for primary reference
standards. Warm up times are on the order of
5 minutes to 0.10 ppm of final frequency.
**Not all
available at
Digi-Key
OH200Package
OH200- = 1.1x1.4 CO8
32
12
F
3C
00
61 Hz
0- M
20 .8
12
2
OH 1
90
78
56
34
12
Fax: 630- 851- 5040
Description
Features
•Frequency Range: 5.0 to 40.0 MHz
•OCXO - Fixed Frequency
•VCOCXO - Voltage Controlled Option
•3.3 Vdc, 5.0 Vdc or 12.0 Vdc Operation
•Available Frequency Stabilities:
±3 ppb, ±5 ppb, ±10 ppb or ±25 ppb
•Available Temperature Ranges:
0 to 70°C, -20 to 70°C, -40 to 70°C or -40 to
85°C
•Low Phase Noise / Phase Jitter
•Available Outputs: CMOS or Sinewave
•Package: 1.1" x 1.4" x 0.5" (CO-8)
•RoHS Compliant / Lead Free
Ordering Information
6
10
03
C
Temperature
Range
Frequency
Stability
06 = ±3 ppb
10 = ±5 ppb
20 = ±10 ppb
50 = ±25 ppb
Supply Voltage
Output Type
OCXO Type
03 = 3.3 Vdc
05 = 5.0 Vdc
12 = 12.0 Vdc
C = CMOS
S = Sinewave
F = Fixed Freq.
V = Voltage
Controlled
Option
5 = 0 to 70°C
6 = -40 to 85°C
7 = -20 to 70°C
8 = -40 to 70°C
{±(Fmax-Fmin)/(2*Fo)}
F
- 012.8M
Output Frequency
Frequency Format
-xxx.xM Min
-xxx.xxxxxxM Max
*Amount of
numbers after the
decimal point.
M = MHz
Example Part Number:
OH200-61003CF-012.8M = 1.1" x 1.4" x 0.5" CO-8 package, -40 to 85°C temperature range, ±5.0 ppb frequency stability, 3.3 Vdc supply voltage, CMOS square wave output, fixed frequency OCXO, 12.8 MHz output frequency.
To order a OH200-61003CF with an output frequency of: 6.4 MHz = OH200-61003CF-006.4M
To order a OH200-61003CF with an output frequency of 16.384 MHz = OH200-61003CF-016.384M.
OH200-712005SV-040.0M = 1.1" x 1.4" x 0.5" CO-8 package, -20 to 70°C temperature range, ±10.0 ppb frequency stability, 5.0 Vdc supply Bulletin
Page
Revision
Date
Cx193
1 of 4
12
19 Nov 2013
voltage, Sinewave output, voltage controlled output frequency VCOCXO, 40 MHz output frequency.
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines for OCXO
Oscillators. @ www.conwin.com/technologies.html
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage (Vcc)
Control Voltage (Vc)
Operating Supply Voltage 3.3 Vdc (Vcc)
Operating Supply Voltage 5.0 Vdc (Vcc)
Operating Supply Voltage 12 Vdc (Vcc)
Minimum
-55
-0.5
-0.5
3.13
4.75
11.40
Nominal
-
-
-
3.30
5.00
12.00
Maximum
125
13.5
7.0
3.47
5.25
12.60
Units
°C
Vdc
Vdc
Vdc
Vdc
Vdc
Notes
Absolute Ratings: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only. The functional operation
of the device at those or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to conditions outside the "recommended
operating conditions" for any extended period of time may adversely impact device reliability and result in failures not covered by warranty.
Operating Specifications
Parameter
Center Frequency: (Fo)
Operating Temperature Range:
T
emperature Code 5
T
emperature Code 6
T
emperature Code 7
T
emperature Code 8
Frequency Calibration: Frequency Stability vs. Change in Temperature:
S
tability Code 06
S
tability Code 10
S
tability Code 20
S
tability Code 50
Frequency Stability vs. Load
Frequency Stability vs. Voltage
Aging: Daily:
5 MHz to 20 MHz
>
20 MHz to 40 MHz
Aging: First Year:
5 MHz to 20 MHz
>20 MHz to 40 MHz
Lifetime Tolerance: (20 Years)
5
MHz to 20 MHz-
>
20 MHz to 40 MHz
Supply Voltage: (Vcc)
V
oltage Code 03
V
oltage Code 05
V
oltage Code 12
Power Consumption: Turn-On
0 to 70°C Models
- 20 to 70°C Models
- 20 to 75°C Models
- 40 to 85°C Models
Power Consumption: Steady State @ 25°C
0
to 70°C Models
- 20 to 70°C Models
- 20 to 75°C Models
- 40 to 85°C Models
Phase Jitter: (BW: 10 Hz to Fo/2)
Models with Fo: 5 MHz to 20 MHz
Models with Fo: >20 MHz to 40 MHz
Short Term Allan Deviation (1s)
Start-Up Time:
Warm Up Time @ 25°C:
Minimum
Nominal
Maximum
0
-40
-20
-40
-0.1
-
-
-
-
-
70
85
70
70
0.1
°C
°C
°C
°C
ppm @ 25°C
-3.0
-5.0
-10.0
-25.0
-5.0
-5.0
-
-
-
-
-
-
3.0
5.0
10.0
25.0
5.0
5.0
ppb
ppb
ppb
ppb
ppb
ppb
1
1
1
1
±5%
±5%
-1.0
-2.0
-
-
1.0
2.0
ppb/day
ppb/day
2
2
-50
-100
-
-
50
100
ppb
ppb
-300
-500
-
-
300
500
ppb
ppb
3
3
3.13
4.75
11.40
3.30
5.00
12.00
3.47
5.25
12.60
Vdc
Vdc
Vdc
4
4
4
-
-
-
-
-
-
-
-
3.00
3.20
3.30
3.80
W
W
W
W
5
5
5
5
-
-
-
-
-
-
-
-
1.10
1.10
1.20
1.50
W
W
W
W
5
5
5
5
-
-
-
-
-
-
-
1.0E-11
-
-
1.0
2.0
-
500
5
ps rms
ps rms
rms
ms
minutes
6
5.0
-
40.0
Notes:
1. Frequency stability vs. change in temperature [±(Fmax-Fmin)/(2*Fo)].
2. At time of shipment after 48 hours of operation.
3. Inclusive of calibration, operating temperature, supply voltage change, load change and 20 years aging.
4. Supply voltage must reach Vcc levels monotonically within a ramp-up time of <12 ms.
5. Measured with Vcc = Nominal, in calm air.
6. Measured @ 25°C, within 5 minutes, referenced one hour after turn-on.
7. To ensure proper operation of VCOCXO, the control voltage input must be biased the nominal control voltage. Failure to bias the Vc input will cause an unstable output condition.
Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches.
© Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications.
Units
MHz
Bulletin
Page
Revision
Date
Notes
Cx193
2 of 4
12
19 Nov 2013
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Phase Noise Characteristics
Typical Phase Noise for OH200-series with CMOS Output Parameter
SSB Phase Noise
5 - 12 MHz
>12- 20 MHz >20 - 30 MHz
>30 - 40 MHz
@1Hz offset
@ 10Hz offset
@ 100Hz offset
@ 1KHz offset
@ 10KHz offset
@ 100KHz offset
-85
-115
-140
-145
-150
-150
-80
-110
-135
-140
-150
-150
-70
-100
-125
-140
-150
-150
-65
-95
-120
-140
-150
-150
Units
Notes
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Input Characteristics - Voltage Controlled Option (OCXO Type Code V)
Parameter
Control Voltage Range:
3.3 Vdc Models
5.0 Vdc Models
12.0 Vdc Models
Frequency Pullability:
Models with Fo 5 to 20 MHz
Models with Fo >20 to 40 MHz
Input Impedance
Minimum
Nominal
Maximum
Units
Notes
0.30
0.50
0.50
1.65
2.50
2.50
3.00
4.50
4.50
V
V
V
Vcc = 3.3 Vdc
Vcc = 5.0 Vdc
Vcc = 12.0 Vdc
±0.4
±0.6
100K
-
-
-
-
-
-
ppm
ppm
Ohms
7
7
Notes
CMOS Output Characteristics (Output Code C)
Parameter
Load
Output Voltage:
3.3 Vdc Models High (Voh)
Low (Vol)
5.0 Vdc Models High (Voh)
Low (Vol)
12.0 Vdc Models High (Voh)
Low (Vol)
Duty Cycle at 50% of Vcc
Rise / Fall Time: 10% to 90%
Spurious Output
Minimum
Nominal
Maximum
Units
3.0
-
4.7
-
4.7
-
45
-
-
-
-
-
-
-
-
50
-
-
-
0.4
-
0.4
-
0.4
55
6
-80
V
-
15
-
pF
V
V
%
ns
dBc
Sinewave Output Characteristics (Output Code S)
Parameter
Load
Output Power
Harmonics
Spurious
Minimum
-
5.0
-
-
Nominal
50
-
-
-
Maximum
-
-
-30
-80
Units
Ohms
dBm:
dBc
dBc
Notes
Package Characteristics
OH200 Package
Hermetically sealed, resistive welded package with grounded case.
Environmental Characteristics
Shock
Sinusoidal Vibration
Random Vibration
Moisture
Marking Permanency
Attachment Method PCB
Resistance to Solder Heat
Solder Process
500 G’s 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D.
0.06” D.A. or 10G’s Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A.
5.35 G’s rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis.
10 cycles, 95% RH, Per MIL-STD-202G, Method 112.
Per MIL-STD-202G, Method 215J.
Through Hole Mounted
Per MIL-STD-202G, Method 210, Condition E.
Bulletin
Cx193
RoHS compliant, lead free. See solder profile.
Page
3 of 4
Attention: System Designers please review Application Note AN2093:
Revision
12
System Design Information and Printed Circuit Board Layout Guidelines for OCXO
Date
19 Nov 2013
Oscillators. @ www.conwin.com/technologies.html
Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches.
© Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications.
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Re stabilization Time
Off Time
<1 Hour
<6 Hour
<24 Hour
1 to 16 Days
>16 Days
Re stabilization Time
<2 Hours *
<12 Hours *
<48 Hours *
48 Hours + 1/4 Off Time *
<6 Days *
* For a given off time, the time required to meet daily aging, short term stability and TEV requirements.
Package Marking
Package Outline
Pin Connections
0.500
Max.
12.70mm
0.035 Dia.
0.88mm Dia.
0.244
6.2mm
1232
0.025
0.635mm
OH200-61003CF
12.8 MHz
123456789012
123456789012
1.417
36mm
1
0.600
15.24mm
5
0.700
17.78mm
Bottom View
4
1.063
0.350 27mm
8.9mm
2
3
Pin Connection
1: Voltage Control or N/C
2: N/C
3: Supply Voltage (Vcc)
4: Output
5: Ground (Case)
Date Code (YYWW)
Model Number
Output Frequency
Serial # Barcode
Serial Number
Pin 1
Keep Out Area: Under the OCXO is a keep out area, do not place any parts in this area.
0.700
17.78mm
1.000
25.4mm
Solder Profile
Temperature
Test Circuit
260°C
260°C
220°C
180°C
150°C
Vcc
Vcc
10 uF
to
100 uF
0.01 uF
Voltage
Control
or
N/C
Output
N/C
120°C
15 pF
Total Output Load
0
10 s
Up to 120 s
60 to 90 s
Typical
Typical
Ground
Meets IPC/JEDEC J-STD-020C
CMOS Output Waveform
Revision History
Revision
00
01
02
03
04
05
06
07
08
09
10
11
12
Date
10/16/09
02/09/10
03/29/10
04/05/10
05/19/11
07/27/11
09/08/11
01/23/12
03/21/12
08/22/12
12/07/12
05/13/13
11/15/*13
Changes
New release
90%
Added -20 to 75C and 50ppb stability.
Changed 75C to 70C
Added 8 = -40 to 70C temperature code.
50%
Corrected temperature on page 2, from -20 to 80c to -40 to 70C
Updated power consumption
10%
Added sinewave models to the data sheet
Changed package height from 0.530" to 0.500"
Changed frequency stability from "Absolute" to "+/-" with note 1 added as reference
Changed marking to Label marking.
Added application note information.
Changed note 4 and removed note from power supply line. and added absolute note.
Added Voltage Controlled Option.
Bulletin
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines for OCXO
Oscillators. @ www.conwin.com/technologies.html
Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches.
© Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications.
Page
Revision
Date
Cx193
4 of 4
12
19 Nov 2013