DRA1 CX Series • 10mm Single Channel DIN Rail Mount SSR Assembly • AC Ratings up to 380 VAC and 5 Amps • 3-15 and 15-32VDC control • Cage style screw terminals for easy connection • Fits standard 35mm DIN rail • Includes LED Status indicator PRODUCT SELECTION Description 3-15 VDC Control 4-15 VDC Control 15-32 VDC Control 5A 5A 5A DRA1-CX240D5 DRA1-CX240D5-B (2) DRA1-CX240D5R DRA1-CXE240D5 DRA1-CXE240D5R 5A 5A DRA1-CX380D5 DRA1-CXE380D5 DRA1-CX380D5R OUTPUT SPECIFICATIONS (1) Description Operating Voltage [VAC] Transient Overvoltage [Vpk] Maximum Load Current [Arms] (3) Minimum Load Current [Arms] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum off-state dv/dt @ maximum rated voltage [V/µsec] (4) Maximum 1 Cycle Surge Current (50/60 Hz) [Apk] Maximum I²t for fusing (50/60 Hz, 1/2 cycle) [A² sec] Maximum On-State Voltage Drop @ Rated Current [Vpk] CX(E)240x5 CX(E)380x5 12-280 600 5 0.06 0.1 500 239/250 285/260 1.4 48-380** 1200 5 0.06 0.1 500 239/250 285/260 1.4 INPUT SPECIFICATIONS (1) Description Control Voltage Range Must Turn On Voltage Must Turn Off Voltage Typycal Input Current Nominal Input Impedance Maximum Turn-On Time [msec] (5) Maximum Turn-Off Time [µsec] DRA1-CX DRA1-CX240D5-B (2) DRA1-CX380D5 DRA1-CXE 3-15 VDC 3.0 VDC 1 .0 VDC 15 mAdc 300 Ohm 1/2 Cycle 1/2 Cycle 4-28 VDC 1.0 VDC 4 .0 VDC 10 mAdc 1360 Ohm 1/2 Cycle 1/2 Cycle 4-15 VDC 4.0 VDC 1 .0 VDC 15 mAdc 240 Ohm 1/2 Cycle 1/2 Cycle 15-32 VDC 15.0 VDC 1 .0 VDC 15 mAdc 1500 Ohm 1/2 Cycle 1/2 Cycle GENERAL SPECIFICATIONS Description Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation Parameters 4000 VRMS 109 Ohms 10 pF -30 to 80°C -30 to 125 °C 0.063 lb (28.6g) Themally Conductive Epoxy GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) The output is normally closed and does not have a LED status indicator 3) See Derating chart on page 3. 4) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 5) Turn-on time for DC control random turn-on versions is 0.1 msec **NOTE: Voltages in excess of 380V will damage output terminals. MECHANICAL SPECIFICATIONS WIRING DIAGRAM THERMAL DERATE INFORMATION AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 E116950 (relay only) LR81689 (relay only) 70938 UG (relay only) Rev. 110811 ANNEX - ENVIROMENTAL INFORMATION