UTMC APPLICATION NOTE _________________________________________________________________ Operational Frequency versus Load Capacitance for UTMC’s RadHard MSI Product Family Introduction The following defines the operational frequency versus load capacitance for UTMC’s RadHard MSI product family. It contains examples and information related to maximum part frequency based on load capacitance and current density. Capacitance loading limits for UTMC’s RadHard MSI Logic devices are also described. The loading limit is defined by the capacitive load that can be driven at the device’s maximum operating frequency and/or at the device’s current density limit. For reliable operation, both limits should be met for the intended operating frequency and device loading. In addition, information is presented for output rise/fall times which may be a consideration in overall system timing. Maximum Frequency Based on Load Capacitance The maximum frequency for any given device in UTMC’s RadHard MSI Logic Product handbook can be derived using the device’s AC Electrical Parameters t PHL and tPLH. The sum of tPHL and tPLH is equal to the reciprocal of the maximum frequency of the device driving a load capacitance (CL) of 50pF as shown in equation 1.0. Equation 1.0 : fMAX = 1 (tPLH + tPHL) As CL increases, the maximum sustainable toggle frequency (f) decreases. The maximum frequency for a given device under different load capacitance can be obtained through use of equation 1.0 by adding a delay derating (∆tP) to each AC electrical parameter (tPLH and tPHL) as shown in equation 1.1. Values for delay deratings as a function of output load capacitance are given in table 1 and table 2 for the 8mA and 12mA drivers respectively. Equation 1.1 : fAC = Where: 1 (tPLH + tPHL + ∆tPLH + ∆tPHL) tPLH and tPHL are values specified in the RadHard MSI Logic Product Handbook for a specific device under worst case conditions. ∆tPLH and ∆tPHL are delay deratings as a function of output load capacitance given in tables 1 and 2. 7/96 1 of 8 Table 1: Propagation delay deratings for RadHard MSI 8mA devices at higher loading 8mA Devices CMOS TTL Load ∆tPLH ∆tPHL 50pF 0ns 0ns 100pF 8ns 8ns 200pF 25ns 26ns 300pF 42ns 44ns 50pF 0ns 0ns 100pF 4ns 7ns 200pF 13ns 23ns 300pF 21ns 38ns Table 2: Propagation delay deratings for RadHard MSI 12mA devices at higher loading 12mA Devices CMOS TTL Load ∆tPLH ∆tPHL 50pF 0ns 0ns 100pF 5ns 6ns 200pF 15ns 17ns 300pF 28ns 29ns 50pF 0ns 0ns 100pF 3ns 5ns 200pF 9ns 14ns 300pF 15ns 25ns Example: Calculate the maximum frequency for device UT54ACS02, (8mA)operating with a load capacitance of 200pF. The RadHard MSI Logic Product Handbook specifies maximum propagation of tPHL = 13ns and tPLH = 11ns, from table 1, ∆tPLH = 25ns and ∆tPHL = 26ns. Therefore, equation 1.1 becomes: 1 fAC = ------------------------------------------------------------------------ = 13.33MHz ( 11ns + 13ns + 25ns + 26ns ) 7/96 2 of 8 where fAC = maximum operating frequency for worst case conditions. Maximum Frequency Based on Current Density Equation 2.0 defines the relationship between maximum operating frequency and load capacitance based upon current density. Equation 2.0 : fMAX = 3765 pF-MHz CL To determine the maximum number of loads a device can drive (i.e., fan-out) modify equation 2.1 as follows: Equation 2.1 : fan-out = 3765 pF-MHz (CIN) (fOP) Where fOP defines the frequency of operation or toggle rate CIN defines input capacitance of the load device. Example: Calculate fan-out for a UT54ACS02 operating with a maximum toggle rate of 18.8MHz. Assume the UT54ACS02 is driving other UTMC RadHard MSI Logic devices which have an input capacitance of 15pF each. fan-out = 3765 pF-MHz = (15pF) (18.8MHz) 13.35loads ≈ 200pF Loading Versus Rise/Fall Times The loading versus rise/fall times for 8mA or 12mA drivers can be determined by using the equations shown in graph 1, 2, 3, or 4. Graphs 1, 2, 3, and 4, represent the relationship between rise/ fall time and loading for three different processing and operating conditions. In many cases it is desirable to maintain a rise/fall time of 5ns or less. Example: Calculate the maximum number of loads that a nominally processed UT54ACS02 can drive while maintaining a rise/fall time of 5ns and assuming nominal operating conditions. 7/96 3 of 8 From graph 1: y = (.048 ns/pF) (x pF) + 1.18ns x = 5ns - 1.18 pF .048 = 79.58pF All UTMC RadHard MSI devices have an input load (CIN) of 15pF which yields: 79.58pF x ÷ 15pF = -------------------- = 5.3loads 15pF Therefore, operating under nominal process and nominal conditions, the number of loads a UT54ACS02 (8mA driver) can drive while maintaining a 5ns rise time with input loads of 15pF each, is 5 loads. Summary This applications note focuses on AC contributions to the operating frequency based on load capacitance. In addition, DC load currents must be considered when determining the maximum number of loads that an output can drive. The DC loading limit is defined by the device’s DC sink and/or source specifications. 7/96 4 of 8 7/96 5 of 8 RISE/FALL TIMES (ns) LOADING (pF) GRAPH 1: Rad-Hard MSI 8mA CMOS Devices Rise/Fall Times vs. Loading y = 0.034x + 0.55 y = 0.048x + 1.18 y = 0.085x + 1.56 7/96 6 of 8 RISE/FALL TIMES (ns) LOADING (pF) GRAPH 2: RadHard MSI 8mA TTL Devices Rise/Fall Times vs. Loading y = 0.028x + 0.31 y = 0.039x + 0.91 y = 0.068x + 1.30 7/96 7 of 8 RISE/FALL TIMES (ns) LOADING (pF) GRAPH 3: Rad-Hard MSI 12mA CMOS Devices Rise/Fall Times vs. Loading y = 0.027x + 0.43 y = 0.034x + 1.46 y = 0.052x + 2.64 7/96 8 of 8 RISE/FALL TIMES (ns) LOADING (pF) GRAPH 4: RadHard MSI 12mA TTL Devices Rise/Fall Times vs. Loading y = 0.025x + 0.95 y = 0.033x + 1.51 y = 0.052x + 2.62