IEC and British Standard Fuses

IEC & British Standard Fuses
IEC and British Standard Fuses
Section Contents
Application Data
Page
Application Data . . . . . . . . . . . . . . . . . . . . . 217-218
HRC fuse holders
CAMaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235
SAFEloc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235
RED indicates NEW information
Supplementary ranges cover applications up to 660Vac and
500Vdc including those with nonstandard tag fixings.
Cooper Bussmann fuses are manufactured under quality
systems independently assessed to BS 5750 (ISO 9002) and
appropriate ratings carry the ASTA 20 endorsement.
Selecting fuses is relatively simple and effective. The
following notes cover the majority of applications. For further
information contact our Application Engineers at
636-527-1270.
Circuit Loading
The current rating of the fuse should not be less than the full
load current of the circuit. The circuit should be so designed
that small overloads of long duration will not be of frequent
occurrence.
Cable Ratings & Protection
There is an increasing move away from 70°C PVC insulation
to materials that are more environmentally friendly, for
example 90°C XLPE. The ratings of fusegear, switches,
accessories, etc. are generally based upon the equipment
being connected to conductors intended to be operated at a
temperature not exceeding 70°C in normal service.
In view of the above, it is recommended that the practice of
designs based upon conductor temperatures of 70°C be
regarded as the norm. The equipment manufacturer should
be consulted to ascertain the reduction of nominal current
rating of the equipment if conductor temperatures exceeding
70°C are used. In addition, an overriding factor is often
voltage drop.
Fuses with gG characteristics protect associated cables
against both overload and short-circuit current, provided that
the current rating of the fuse 1N is equal or less than the
current carrying capacity of the cable 1z.
In motor circuits, the motor starter will provide the overload
protection and the fuses will provide the short-circuit
protection. The maximum fuse size that can be used
depends upon the type of cable used and is determined
using the appropriate K factor. The following table gives the
maximum sizes of fuses that are recommended for two
popular cables with copper conductors, 70°C PVC (K = 115)
and 90°C thermosetting (K = 143).
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
217
IEC &
British
Fuses
CSA Type P and Type D fuses
(CDS, CDN & PON) . . . . . . . . . . . . . . . . . . . . . . . . . . . .219
Tron® HRC Form II Class C fuses
(CGL Form II Class C) . . . . . . . . . . . . . . . . . . . . . . . . . . 220
HRCI Industrial ceramic body fuses (CIF21 HRCI-CA &
CIF06 HRCI-CB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
HRCI-J Fast-acting fuses (CJ HRCI-J) . . . . . . . . . . . . . . . 222
HRCI-Miscellaneous Type K fuses (CIH, CIK &
CIL HRCI-MISC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
HRC Form II current-limiting fuses . . . . . . . . . . . . . . . . . .224
BS 88 British Standard low voltage fuses (SSD, NSD,
ESD & STD, NITD, AAO, BAO, OSD, CEO,
DEO BS 88 Part 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225
BS 88 British Standard low voltage fuses (AC, AD, BC,
BD, CD, DD, ED, EFS & EF, FF, FG, GF, GG,
GH BS 88) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226
DIN Style Type D (D16, D27, D33, D125 Type D) . . . . . . 227
Neozed low voltage fuses (NZ01, NZ02 Type D0) . . . . . . 227
NH HRC Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228-231
Class gG/gL IEC Industrial ferrule fuses (C08G, C08M,
C10G, C10M, C14G, C14M, C22G, C22M) . . . . . . . . . . 232
Class aM IEC Industrial ferrule fuses (C08M, C10M,
C14M, C22M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233
Class aM & gG/gL IEC Industrial ferrule fuses with striker
(C14G_S, C22G_S, C14M_S, C22M_S) . . . . . . . . . . . . . 234
The standard range of fuses for low voltage industrial and
general purpose applications meet the requirements of
BS 88 and IEC 60269. By using advanced fuse technology,
current ratings up to 400A have compact dimensions, but
retain standard dimensional and performance requirements.
These designs are for 315/240V systems. The standard
range of fuses are available from 2-1250A in the following
tag forms: Offset Blade - Offset Bolted - Center Bolted.
IEC & British Standard Fuses
Application Data for BS Low Voltage Fuses
Cable Size (mm2)
1
1,5
2.5
4
6
10
16
25
35
50
70
95
120
Max. Fuse Rating (amps)
K = 115
K = 143
16
16
20
25*
32*
32*
50*
50*
63*
63*
100*
125*
125*
160*
200*
250*
315*
355*
400*
500
560
630
710
800
800
1000
* Extended Motor Circuit dual ratings can be used.
Protection Against Electrical Shock
For a TN System, a disconnecting time not exceeding 5s is
permitted for a distribution circuit. The maximum values of
earth fault loop impedance (Zs) of 240V for Cooper
Bussmann gG fuses to BS 88: Parts 2 and 6 are:
Rating (A) Zs (Ohms) Rating (A) Zs (Ohms) Rating (A) Zs (Ohms)
6
14
50
1.1
250
0.16
10
7.7
63
0.86
315
0.13
16
4.3
80
0.60
400
0.096
20
3.0
100
0.44
500
0.073
25
2.4
125
0.35
630
0.054
32
1.9
160
0.27
800
0.044
40
1.4
200
0.20
Ambient Temperature
The derating, in terms of current, of 0.5% per °C above an
ambient of 35°C is recommended.
Capacitor Circuits
For power factor correction in capacitor circuits, the fuse
should be chosen with a current rating greater than 1.5 times
the rated capacitor current. This takes into account the high
inrush current, circuit harmonics and capacitor tolerances.
Motor Circuits
In motor circuits, the fuse has to withstand the motor's
starting current and often requires a higher rating than the
motor's full load current. Coordination recommendations are
made by the manufacturers of motor starters in accordance
with IEC 60947-4-1. To get Type 2 coordination with fuses,
tests are performed with the latest gG or gM fuses to BS 88
or IEC 60269 that have pre-arcing I2t values towards the
bottom of specified limits. This means that Cooper
Bussmann fuses are suitable to provide Type 2 coordination.
Extended dual ratings of motor circuit protection fuses with
gM characteristics are available in most popular fuse sizes to
extend the use of associated equipment with appropriate
economies. In the majority of applications, gG fuses are
used. It is not essential to use gM fuses for motor circuit
protection, they simply extend the utilization of standard
equipment.
Below is a table of recommended fuses at 415V. In most
applications, the run-up time is less than 5 seconds and duty
is infrequent - no more than twice per hour. The next larger
rating should be used for more demanding applications.
Interrupting Rating
The standardized interrupting rating values are 80kA for
voltages of 415Vac and above, and 40kA for DC
applications. The 240Vac designs have an interrupting rating
of 50kA.
Coordination Ratio
All fuses to BS 88 Parts 2 and 6 will give a coordination ratio
of 2:1; and for most practical situations a ratio of 1.6:1 (two
steps in the R10 series). Example: an upstream fuse rated at
160A will coordinate with a downstream fuse rated at 100A.
Current and Energy Limitation
The range of fuses have pre-arcing I2t values towards the
bottom limits of BS 88 Parts 2 and 6. This ensures excellent
current and energy limitation. They also have lower power
losses at rated current. This assists in the appropriate
interchangeability with other makes of fuses.
Transformers
When fuses are used on the primary side of transformers,
the normal fuse current rating should be at least twice the
nominal transformer primary current.
Fluorescent Lighting
The normal fuse current rating should be at least twice the
normal full load current of the maximum number of lights to
be simultaneously switched.
218
kW
0.25
0.37
0.55
0.75
1.1
1.5
2.2
3.0
4.0
5.5
7.5
11.0
15.0
18.5
22.0
30.0
37.0
45.0
55.0
75.0
90.0
110.0
132.0
150.0
185.0
200.0
225.0
250.0
280.0
335.0
355.0
Rating Motor
A
0.8
1.1
1.5
2.0
30
3.6
5.0
6.5
8.4
11.0
15.0
20.0
27.0
33.0
38.0
54.0
66.0
79.0
98.0
135.0
155.0
185.0
220.0
250.0
310.0
335.0
375.0
415.0
460.0
562.0
596.0
Direct On-line
Standard
Motor Circuit
(gG)
(gM)
A
A
4
4
6
6
10
16
16
20
20
25
20M25
40
32M40
50
32M50
63
32M63
80
63M80
80
63M80
100
63M100
125
100M125
160
100M160
160
100M160
250
200M250
250
200M250
315
200M315
355
315M400
355
315M400
450
400M500
500
4 00M500
560
560
630
710
800
-
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
Asst. Start
Standard
(gG)
A
2
2
4
4
6
01
01
61
61
2 20
25
32
40
50
50
80
80
100
100
160
160
200
250
315
355
400
400
450
500
630
710
IEC & British Standard Fuses
CSA Type P and Type D Fuses
CDS, CDN & PON Type P & D
Specifications
Description: CSA time-delay Type D & P
fuses.
Dimensions: See Catalog Numbers table
and Dimensions illustration.
Ratings:
Volts: — 250Vac (CDN & PON)
— 600Vac (CDS)
Amps: — 10-600A
IR: — 10kA minimum
Agency Information: CE, CSA Certified to C22.2 No. 59.1.
Features and Benefits
• Economical fuse in a variety of ratings for applications not
requiring time-delay.
Dimensions
A
IEC &
British
Fuses
Typical Applications
• Lighting, heating and other circuits not subject to temporary
surges and where available short-circuit current are
relatively low.
B
Basic Catalog Numbers
Ferrule Design—1 through 60A
Time-Delay CSA Type “D” Fuses
Catalog
Numbers
CDN
CDS
Amp
Ratings
Below 10A use FRN-R 10, 12, 15, 20, 25, 30,
35, 40, 45, 50, 60, 70, 80, 90, 100
110, 125, 150, 175, 200, 225, 250, 300, 350, 400,
450, 500, 600
Below 10A use FRS-R 10, 12, 15, 20, 25, 30,
35, 40, 45, 50, 60
70, 80, 90, 100, 110, 125, 150, 175, 200,
225, 250, 300, 350, 400, 450, 500, 600
Volts
250Vac
600Vac
C
A
D
B
F
E
Knife Blade—70 through 600A
One-Time CSA Type “P” Fuses
Catalog
Number
PON
Amp
Ratings
15, 20, 25, 30, 35, 40, 45, 50, 60
Volts
250Vac
Catalog Numbers
Basic Catalog
Number
and Volts
CDN/PON 250Vac
CDS 600Vac
Amp
Ratings
1-30
35-60
70-100
110-200
225-400
450-600
1-30
35-60
70-100
110-200
225-400
450-600
A
Overall
2.0 (50.8)
3.0 (76.2)
5.88 (149.4)
7.3 (185.4)
8.63 (219.2)
10.38 (263.7)
5.0 (127.0)
5.5 (139.7)
7.88 (200.2)
9.63 (244.6)
11.63 (295.4)
13.38 (339.9)
B Max
Diameter
0.56 (14.3)
0.81 (20.6)
—
—
—
—
0.81 (20.6)
1.06 (27.0)
—
—
—
—
Dimensions in (mm)
C Min
D Min
Blade Length
Barrel Length
—
—
—
—
1.0 (25.4)
—
1.38 (34.9)
4.13 (104.8)
1.88 (47.6)
4.63 (117.5)
2.25 (57.2)
5.19 (131.8)
—
—
—
—
1.0 (25.4)
—
1.38 (34.9)
6.13 (115.6)
1.88 (47.6)
7.13 (118.1)
2.25 (57.2)
8.19 (208.0)
E
Blade Thickness
—
—
0.13 (3.2)
0.19 (4.8)
0.25 (6.4)
0.25 (6.4)
—
—
0.13 (3.2)
0.19 (4.8)
0.25 (6.4)
0.25 (6.4)
F
Blade Width
—
—
0.75 (19.1)
1.13 (28.6)
1.63 (41.3)
2 (50.8)
—
—
0.75 (19.1)
1.13 (28.6)
1.63 (41.3)
2 (50.8)
To Order
To order, specify Basic Catalog Number and amp rating. Example: CDN-30
Data Sheet: 4126
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
219
IEC & British Standard Fuses
Tron® HRC Form II Class C Fuses
CGL Form II Class C
Specifications
Description: Current-limiting HRCII-C fuses
designed to withstand inrush currents on
typical motor start-ups while offering high
current limitation in the short-circuit region.
Dimensions: See Dimensions illustrations.
Ratings:
Volts: — 600Vac/250Vdc (1-30A)
Amps: — 1-600A
IR: — 200kA (40,000A DC)
Agency Information: CE, CSA Certified,
C22.2 No. 106.
Dimensions
0.22"
0.81"
0.22"
(20.64mm)
(5.56mm) (5.56mm)
0.06"
2.0"
(1.59mm)
0.34"
(50.8mm)
2.80"
0.94"
(8.73mm)
(23.81mm)
(71.04mm)
3.31"
(84.14mm)
CGL 1-30
0.22"
0.81"
0.22"
(20.64mm)
(5.56mm) (5.56mm)
0.06"
2.0"
(50.8mm)
(1.59mm)
0.50"
2.80"
1.06"
(12.7mm)
(71.04mm)
(26.92mm)
3.5"
(88.9mm)
Features and Benefits
• Close sizing to loads allows using smaller and less costly
switches
• Provides a higher degree of short-circuit protection
• Helps protect motors against burnout from overloads
CGL 35-60
0.343"
0.343"
(8.71mm)
(8.71mm)
2.39"
Typical Applications
• For use in circuits subject to surge currents such as those
caused by motors, transformers and other inductive loads
(60.72mm)
3.64"
1.34"
(34.04mm)
0.09"
(2.29mm)
0.75"
1.375"
(19.05mm)
(34.93mm)
(92.47mm)
4.31"
(109.54mm)
CGL 70-100
Catalog Numbers (-Amps)
CGL-1
CGL-2
CGL-3
CGL-4
CGL-6
CGL-10
CGL-15
CGL-20
CGL-25
CGL-30
CGL-35
CGL-40
CGL-45
CGL-50
CGL-60
CGL-70
CGL-80
CGL-90
CGL-100
CGL-110
CGL-125
CGL-150
CGL-175
CGL-200
CGL-225
CGL-250
CGL-300
CGL-350
CGL-400
CGL-450
CGL-500
CGL-600
0.343"
(8.71mm)
0.343
(8.71mm)
0.125"
3.00"
(3.18mm)
0.75"
(76.2mm)
(19.05mm)
4.30"
(109.22mm)
1.50"
(38.1mm)
5.31"
(134.87mm)
CGL 110-200
0.19"
(4.76mm)
1.0"
0.38"
(25.4mm)
(9.53mm)
1.0"
(25.4mm)
3.0"
2.38"
(76.2mm)
(60.33mm)
5.25"
(133.35mm)
8.19"
(207.96mm)
CGL 225-400
1.0"
0.41"
(25.4mm)
(10.32mm)
1.0"
(25.4mm)
.60"
3.0"
(15.24mm)
(76.2mm)
5.25"
(133.35mm)
8.19"
(207.96mm)
CGL 450-600
Data Sheet: 4125
220
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
0.375"
(9.53mm)
3.00"
(76.2mm)
IEC & British Standard Fuses
HRCI Industrial Ceramic Body Fuses
CIF21 HRCI-CA
CIF06 HRCI-CB
Specifications
Description: The HRCI-CA fuse provides
both overload and short-circuit protection to
HRCI requirements. Offset blades for bolt-on
mounting. CIF21 fuse fits the Cooper
Bussmann CAMaster fuse holder (see data
sheet 4132).
Dimensions: See Dimensions illustration.
Construction: Ceramic body.
Ratings:
Volts: — 600Vac/250Vdc
Amps: — 1-30A
IR: — 200kA RMS Sym.
Agency Information: CE, CSA C22.2, No. 106-M92.
Mounting: Bolt-on.
Specifications
Description: A miniature industrial fuse that
provides both short-circuit and overload
protection and the CIF06 fits the 30A
SAFEloc fuse holder.
Dimensions: See Dimensions illustration.
Construction: Ground ceramic body with
plated end caps.
Ratings:
Volts: — 600Vac/250Vdc
Amps: — 1-30A
IR: — 200kA RMS Sym.
Agency Information: CE, CSA C22.2 No. 106-M92 (3-30A
only).
Mounting: Clip-in offset blades.
Catalog Numbers
Catalog Number
Amp
Ratings
1
3
6
10
15
20
25
30
Catalog
Numbers
1CIF06
3CIF06
6CIF06
10CIF06
15CIF06
20CIF06
25CIF06
30CIF06
Features and Benefits
• Close sizing to loads allows using smaller and less costly
switches
• Provides a higher degree of short-circuit protection
• Helps protect motors against burnout from overloads
Typical Applications
• For use in circuits subject to surge currents such as those
caused by motors, transformers and other inductive loads
IEC &
British
Fuses
Catalog
Numbers
1CIF21
3CIF21
6CIF21
10CIF21
15CIF21
20CIF21
25CIF21
30CIF21
Amp
Ratings
1
3
6
10
15
20
25
30
Features and Benefits
• Close sizing to loads allows using smaller and less costly
switches
• Provides a higher degree of short-circuit protection
• Helps protect motors against burnout from overloads
Typical Applications
• For use in circuits subject to surge currents such as those
caused by motors, transformers and other inductive loads
Dimensions - in (mm)
Dimensions - in (mm)
2.15 (54.5)
1.44 (35.5)
0.19 (4.7)
0.54 (13.8)
2.38 (60.4)
1.44 (35.5)
0.44 (11.1)
0.54 (13.8)
0.5 (12.7)
0.03 (3.5)
1.75 (44.5)
Data Sheet: 4127
0.03 (0.81)
0.14 (3.5)
Data Sheet: 4128
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
221
IEC & British Standard Fuses
HRCI-J Fast-acting Fuses
Dimensions
CJ HRCI-J
Specifications
Description: HRCI-J fast-acting
fuses are industrial duty fuses with
the excellent current-limiting
characteristics of fast-acting HRCI-J
fuses to limit damage to equipment
and installations by the thermal and
magnetic energy associated with a
large short-circuit fault current.
Overload characteristics limit cable
damage due to low overload currents.
Dimensions: See Catalog Numbers table and Dimensions
illustrations.
Construction: Ceramic body fuse.
Ratings:
Volts: — 600Vac (or less), 250Vdc
Amps: — 1-600A
IR: — 200kA
Agency Information: CSA C22.2 No. 106 M92; Designed
to BS 88:2, IEC 60269-2.
1CJ to 60CJ
A
B
B
C
70CJ to 600CJ
E
J
C
A
K
F
H
D
B
G
Catalog Numbers
Catalog Numbers
Catalog
Numbers
1CJ
3CJ
6CJ
10CJ
15CJ
20CJ
25CJ
30CJ
35CJ
40CJ
45CJ
50CJ
60CJ
70CJ
80CJ
90CJ
100CJ
110CJ
125CJ
150CJ
175CJ
200CJ
225CJ
250CJ
300CJ
350CJ
400CJ
450CJ
500CJ
600CJ
Amp
Ratings
1
3
6
10
15
20
25
30
35
40
45
50
60
70
80
90
100
110
125
150
175
200
225
250
300
350
400
450
500
600
Dimensions in (mm)
A
B
C
D
E
F
G
H
J
K
2.25 (57)
0.5 (12.7)
0.81 (20.6)
—
—
—
—
—
—
—
2.38 (60)
0.63 (16)
1.06 (27)
—
—
—
—
—
—
—
4.63 (117)
3.63 (92)
1.13 (28)
0.75 (19)
0.13 (3.2)
1 (25.4)
0.5 (12.7)
0.28 (7.1)
0.38 (9.5)
2.63 (67)
5.75 (146)
4.38 (111)
1.63 (41)
1.13 (28.6)
0.19 (4.8)
1.38 (35)
0.69 (17.5)
0.28 (7.1)
0.38 (9.5)
3 (76)
7.13 (181)
5.25 (133)
2.13 (54)
1.63 (41)
0.25 (6.3)
1.88 (47.6)
0.94 (24)
0.41 (10.3)
0.53 (13.5)
3.38 (86)
8 (203)
6 (152)
2.63 (66)
2 (51)
0.38 (9.5)
2.13 (54)
1 (25.4)
0.53 (13.5)
0.69 (17.5)
3.75 (96)
Data Sheet: 4129
222
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
IEC & British Standard Fuses
HRCI - Miscellaneous Type K Fuses
CIH, CIK & CIL HRCI-MISC
Specifications
Description: HRI fuses provide both overload
and short-circuit protection, featuring offset
blades for bolt down mounting.
Dimensions: See Catalog Numbers table and
Dimensions illustration.
Construction: Ceramic body.
Ratings:
Volts: — 600V
Amps: — 1-100A
IR: — [email protected]
Agency Information: CE, CSA C22.2 No.
106 M92.
Dimensions
G
J
E
IEC &
British
Fuses
K
F
A
D
B
L
C
H
G
(The CIL14 has a rejection hole, not a slot as shown above.)
Catalog Numbers
Catalog
Amp
Numbers Ratings
1CIH07
1
3CIH07
3
6CIH07
6
10CIH07
10
15CIH07
15
20CIH07
20
25CIH07
25
30CIH07
30
35CIK07
35
40CIK07
40
50CIK07
50
60CIK07
60
80CIL14
80
90CIL14
90
100CIL14
100
A Max
2.25 (57)
B Max
0.94 (24)
C Max
3.38 (86)
D Nom
0.38 (9.2)
Dimensions: in (mm)
E Nom
F Nom
G Nom
0.04 (1.0)
2.88 (73)
0.21 (5.2)
2.25 (57)
0.94 (24)
3.38 (86)
0.38 (9.2)
0.04 (1.0)
2.28 (58)
1.06 (27)
3.56 (91)
0.5 (12.7)
0.05 (1.2)
2.28 (58)
1.06 (27)
3.56 (91)
0.5 (12.7)
0.05 (1.2)
2.75 (70)
2.75 (70)
1.44 (37)
1.44 (37)
4.38 (111)
4.38 (111)
0.75 (19)
0.75 (19)
0.09 (2.5)
0.09 (2.5)
3.69 (94)
3.69 (94)
2.88 (73)
H Nom
0.31 (8)
J Max
1 (25.4)
K Nom
0.10 (2.6)
L Max
2.38 (60)
1 (25.4)
0.10 (2.6)
2.38 (60)
0.21 (5.2)
0.31 (8)
2.88 (73)
0.21 (5.2)
0.41 (10.5)
1.09 (28)
0.13 (3.2)
2.38 (61)
2.88 (73)
0.21 (5.2)
0.41 (10.5)
1.09 (28)
0.13 (3.2)
2.38 (61)
0.34 (8.7)
0.34 (8.7)
0.41 (10.5)
0.41 (10.5)
1.5 (38.5)
1.5 (38.5)
—
2.91 (74)
2.91 (74)
—
Recommended Fuse Holders
Fuse
1-30A
35-60A
Fuse Holder
CM30CF
CM60CF
Data Sheet: 4130
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
223
IEC & British Standard Fuses
HRC Form II Current-limiting Fuses
Dimensions
HRC Form II
F
Specifications
Description: HRC Form II
current-limiting fuses.
Dimensions: See Catalog
Numbers table and Dimensions
illustrations.
Construction: Ceramic body.
Ratings:
Volts: — 600Vac (or less)
— 250Vdc
Amps: — 2-600A
IR: — 200kA RMS Sym.
Agency Information: CE, CSA C22.2 No.106M1992;
BS 88:2, IEC 60269:2.
G
J
A
D
E
H
C
F
J
E
A
G
D
B
C
C
G
B
A
H
E
K
K
F
B
A
G
P11C/R11C
(Center Blades)
D
H
E
C
Catalog Numbers
1.38 (35)
L09C/M09C/P09C
(Center Blades)
D
F
A
1.38 (35)
B
0.56 (14)
0.56 (14)
C
3.38 (85)
3.38 (85)
D
0.38 (9)
Dimensions in (mm)
E
F
0.06 (1.2)
2.88 (73)
G
0.22 (5.6)
H
0.31 (8)
0.38 (9)
J
K
0.56 (14) —
0.56 (14)
CSA Category
HRCII-C
—
HRCII-C
3.44 (87)
3.44 (87)
0.06 (1.2)
2.88 (73)
0.22 (5.6)
0.31 (8)
0.5 (13)
0.06 (1.2)
2.88 (73)
0.22 (5.6)
0.31 (8)
2.19 (56)
0.88 (22)
2.19 (56)
2.19 (56)
0.88 (22)
0.88 (22)
3.75
3.75(95)
(95)
0.5 (13)
0.5 (13)
0.06 (1.2)
2.88 (73)
0.22 (5.6)
0.31 (8)
2.38
2.38 (60)
(60)
0.88 (21.4)
(21.4)
0.88
4.38 (111)
0.56 (14.3)
(14.3)
0.56
0.13 (3.2)
(3.2)
0.13
3.69 (94)
0.34 (8.7)
2.56 (65)
2.56 (65)
1.5 (38)
1.5 (38)
4.38 (111)
0.75 (19)
0.75 (19)
0.09 (2.4)
0.09 (2.4)
3.69 (94)
0.34 (8.7)
2.38
2.38 (60)
(60)
0.88 (21.4)
(21.4)
0.88
5 5(127)
(127)
0.56
0.56 (14)
(14)
0.13 (3.2)
4.38 (111)
0.34 (8.7)
2.56 (65)
2.56 (65)
1.5 (38)
1.5 (38)
5.38 (136)
0.75 (19)
0.75 (19)
0.13
0.13 (3.2)
(3.2)
4.38 (111)
0.34 (8.7)
0.34 (8.7)
3.06 (178)
2.31 (59)
5.38 (136)
1 (25.4)
0.19 (4.8)
4.38 (111)
4.38 (111)
0.34 (8.7)
3.19 (81)
3.19 (81)
2.31 (59)
2.31 (59)
2.88 (73)
2.88 (73)
8.25 (210)
8.25 (210)
8.25 (210)
1 (25.4)
1 (25.4)
0.19 (5)
1 (25.4)
0.25 (6.3)
0.25 (6.3)
HRCII-MISC
HRCII-MISC
0.44 (11)
11 (25.4)
(25.4)
——
HRCII-C
HRCII-C
0.44 (11)
0.44 (11)
—
—
—
HRCII-MISC
—
0.44 (11)
——
——
HRCII-MISC
HRCII-MISC
0.56 (14)
0.56 (14)
—
—
—
HRCII-C
HRCII-C
0.5 (13)
—
—
0.5 (13)
0.19 (4.8)
3.06 (178)
3.06 (178)
0.88 (22) —
—
0.88 (22)
0.88 (22) —
—
5.25 (133)
0.41 (10)
0.63 (16)
5.25 (133)
5.25 (133)
0.41 (10)
0.41 (10)
0.63 (16)
0.63 (16)
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
—
—
—
0.19 (5)
Data Sheet: 4131
224
K07C/K07CR/
L14C/M14C
(Offset Blades)
H
Typical Applications
• Used to protect motor control circuits, together with
contactors and overload protection relays to provide Type 2
coordination - per IEC 60947-4.
Catalog
Amp
Numbers Ratings
2H07C
2
4H07C
4
6H07C
6
10H07C
10
15H07C
15
20H07C
20
25H07C
25
30H07C
30
40K07C
40
50K07C
50
60K07C
60
80K07CR
80
100K07CR 100
80L14C
80
100L14C
100
125M14C
125
150M14C
150
200M14C
200
80L09C
80
100L09C
100
125M09C
125
150M09C
150
200M09C
200
250P09C
250
300P09C
300
350P09C
350
400P09C
400
250P11C
250
300P11C
300
350P11C
350
400P11C
400
450R11C
450
500R11C
500
600R11C
600
H07C
(Offset Blades)
B
—
1 (25)
—
1 (25)
—
1 (25)
1 (25)
—
HRCII-C
HRCII-MISC
HRCII-MISC
HRCII-C
HRCII-C
HRCII-C
IEC & British Standard Fuses
BS 88 British Standard Low Voltage Fuses
SSD, NSD, ESD BS 88 Part 1
Specifications
Description: The NSD and ESD are low voltage
fuses complying with general purpose gG
characteristics.
Construction: Ceramic body.
Ratings:
Volts: — 240-550Vac (See Catalog Numbers table)
Amps: — 2-63A (See Catalog Numbers table)
— 20M25-63M100A Motor Starter ratings
(See Catalog Numbers table)
IR: — 33kA (SSD)
— 80kA (NSD, ESD)
Agency Information: CE, Meets the requirements of
BS 88 Part 1 and IEC 60269-1.
Mounting: Offset blades.
ESD
Amp
Ratings
2, 4, 6, 10, 16, 20, 25, 32
2, 4, 6, 10, 16, 20, 25, 32,
20M25*, 20M32*, 20M36*, 32M36*, 32M40*,
32M50*, 32M63*
2, 4, 6, 10, 16, 25, 32
40, 50, 63, 63M80, 63M100*
Max AC
Voltage
Ratings
240
550
415
415
550
415
BS 88
Ref.
E1
F1
F1
F1
F2
F2
*“M” indicates motor starter ratings.
To Order
To order, specify Basic Catalog Number and amp rating. Example: SSD-20
Recommended Fuse Holders
Basic Fuse
Catalog Numbers
NSD
ESD
Holder Catalog
Numbers
32NNSF
63ENSF
Specifications
Description: The STD to DEO types are low
voltage fuses complying with general purpose gG
characteristics.
Construction: Ceramic body.
Ratings:
Volts: — 240-550Vac (See Catalog Numbers
table)
Amps: — 2-200A (See Catalog Numbers table)
— 20M25-200M315A Motor Starter ratings
(See Catalog Numbers table)
IR: — 33kA (STD)
— 80kA (NITD, AAO, BAO, CEO, DEO)
Agency Information: CE, Meets the requirements of
BS 88 Part 1 and IEC 60269-1.
Mounting: Offset bolted blades.
IEC &
British
Fuses
Basic Catalog Numbers
Basic
Catalog
Numbers
SSD
NSD
STD, NITD, AAO, BAO, OSD, CEO, DEO
BS 88 Part 1
Typical Applications
• The STD type are used in 240V street lighting cut-outs.
• NITD to DEO types used for industrial and general purpose
applications
Basic Catalog Numbers
Basic
Catalog
Numbers
STD
NITD
AAO
BAO
CEO
DEO
OSD
Amp
Ratings
2, 4, 6, 10, 16, 20, 25, 32
2, 4, 6, 10, 16, 20, 25, 32
20M25*, 20M32*, 32M40*, 32M50*, 32M63*
2, 4, 6, 10, 16, 20, 25, 32, 32M40*, 32M50*, 32M63*
40, 50, 63, 63M80*, 63M100*
32, 40, 50, 63, 80, 100
100M125*, 100M160*, 100M200*
125, 160, 200, 200M250*, 200M315*
80, 100
100M125*, 100M160*
Max AC
Voltage BS 88
Ratings Ref.
240
—
550
—
415
—
550
—
550
A3
550
A4
415
A4
415
—
550
—
415
—
*“M” indicates motor starter ratings.
To Order
To order, specify Basic Catalog Number and amp rating. Example: BAO-16
Recommended Fuse Blocks & Holders
Basic Fuse
Catalog Numbers
NITD
AAO
BAO
OSD
CEO
Data Sheets 4105 (SSD), 4100 (NSD) and 4101 (ESD)
Block/Holder
Catalog Numbers
CM32FC
CM32F
CM63F
CM100F
BH-0111
Data Sheets 4123 (STD), 4106 (NITD), 4109 (AAO), 4112
(BAO), 4107 (OSD), 4115 (CEO) and 4117 (DEO)
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
225
IEC & British Standard Fuses
BS 88 British Standard Low Voltage Fuses
AC, AD, BC, BD, CD, DD, ED, EFS BS 88
Specifications
Description: Low voltage fuses that
comply with general purpose gG
characteristics and available up to 400A
with two hole mount and up to 1250A
with four hole mount.
Construction: Ceramic body.
Ratings:
Volts: — 415/550Vac, 250Vdc (See
Catalog Numbers table)
Amps: — 2-400A (See Catalog Numbers table)
— 63M80-400M500A Motor Starter ratings (See
Catalog Numbers table)
IR: — See Catalog Numbers table
Agency Information: CE, Meets the requirements of
BS 88 Parts 1 and 2 and IEC 60269-1.
Mounting: Center bolted blades, two-hole mount.
Specifications
Description: Low voltage fuses
complying with general purpose gG
characteristics and available up to
400A with two hole mount and up
to 1250A with four hole mount.
Construction: Ceramic body.
Ratings:
Volts: — 415/550Vac, 250/400Vdc
(See Catalog Numbers table for details)
Amps: — 355-1250
IR: — See Catalog Numbers table
Agency Information: CE, Meets the requirements of
BS 88 Parts 1 and 2 and IEC269-1.
Mounting: Center bolted blades, four-hole mount.
Basic Catalog Numbers
Basic Catalog Numbers
Basic
Catalog
Numbers
AC
AD
BC
BD
CD
DD
ED
EFS
Amp
Ratings
2, 4, 6, 10, 16, 20, 25, 32
2, 4, 6, 10, 16, 20, 25, 32
40, 50, 63
63M80*, 63M100*
40, 50, 63
80, 100, 100M125*, 100M160*,
100M200*, 100M200*
125, 160, 200,
200M250*, 200M315*
250, 315, 355, 400, 315M400*
400M500*
125, 160, 200, 250, 315
Interrupting
Ratings
AC
DC
80kA 40kA
80kA 40kA
80kA 40kA
80kA
—
80kA 40kA
80kA
—
Max Voltage
Ratings
BS 88
AC
DC
Ref.
550 250
—
550 250
—
550 250
—
550 —
—
550 250
—
415
—
EF, FF, FG, GF, GG, GH
BS 88
B1
80kA
—
415
—
B2
80kA
80kA
80kA
—
—
415
550
415
—
—
—
B3
B4
—
Basic
Catalog
Numbers
EF
Interrupting
Max Voltage
Amp
Ratings
Ratings
BS 88
Ratings
AC
DC
AC
DC
Ref.
355, 400
80kA
—
415
—
C1
400M500*
80kA
—
550
—
—
FF
450, 500, 560, 630
80kA
40kA
550
400
C2
FG
450, 500, 560, 630
80kA
40kA
550
400
—
GF
710, 800
80kA
40kA
550
250
C3
GG
710, 800
80kA
40kA
550
250
—
1000, 1250
80kA
—
550
—
—
GH
710, 800, 1000, 1250
80kA
—
550
—
—
*“M” indicates motor starter ratings.*“M” indicates motor starter ratings.
To Order
To order, specify Basic Catalog Number and amp rating. Example: FG-450
*“M” indicates motor starter ratings.
To Order
To order, specify Basic Catalog Number and amp rating. Example: BC-40
Recommended Fuse Blocks & Holder
Basic Fuse
Catalog Numbers
AC
AD
BC
BD
CD
DD
ED
Block/Holder
Catalog Numbers
BH-0111 Modular fuse block
200DF Fuse holder
BH-0111 Modular fuse block
200DF Fuse holder
200DF Fuse holder
200DF Fuse holder
BH-1131 Modular fuse block
Data Sheets 4110 (AC), 4111 (AD), 4113 (BC), 4114 (BD),
4116 (CD), 4118 (DD), 4119 (ED) and 4121 (EFS)
226
Data Sheets 4120 (EF), 4102 (FF), 4122 (FG), 4103 (GF), 4104
(GG) and 4108 (GH)
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
IEC & British Standard Fuses
DIN Style Type D and Neozed Low Voltage Fuses
D16, D27, D33, D125 Type D
NZ01, NZ02 Type D0
Specifications
Description: DIN style Type D
low voltage fuses.
Dimensions: See Catalog
Numbers table and Dimensions
illustrations.
Construction: Ceramic body.
Ratings:
Volts: — 500Vac
Amps: — 2-100A
IR: — 100kA
Agency Information: CE, “D” type fuses complying with
DIN 49360 Part 2 and DIN 49515, operating class gL.
Catalog Numbers
Amp
Ratings
2
4
6
10
16
20
25
2
4
6
10
16
20
25
35
50
63
80
100
Dimension
“D” (mm)
6
6
6
8
10
12
14
6
6
6
8
10
12
14
16
18
20
5
7
Color
Code
Pink
Brown
Green
Red
Grey
Blue
Yellow
Pink
Brown
Green
Red
Grey
Blue
Yellow
Black
White
Copper
Silver
Red
Figure
Number
1
2
Catalog
Numbers
2NZ01
4NZ01
6NZ01
10NZ01
16NZ01
20NZ02
25NZ02
35NZ02
50NZ02
63NZ02
Amp
Ratings
2
4
6
10
16
20
25
35
50
63
Dimension
“D” (mm)
11
11
11
11
11
15
15
15
15
15
Color
Code
Pink
Brown
Green
Red
Grey
Blue
Yellow
Black
White
Copper
IEC &
British
Fuses
Catalog
Numbers
2D16
4D16
6D16
10D16
16D16
20D16
25D16
2D27
4D27
6D27
10D27
16D27
20D27
25D27
35D33
50D33
63D33
80D125
100D125
Specifications
Description: Low voltage Neozed fuses
suitable for use on 250Vdc systems.
Dimensions: See Catalog Numbers table and
Dimensions illustration.
Construction: Ceramic body.
Ratings:
Volts: — 400Vac
Amps: — 2-63A
IR: — 100kA
Agency Information: CE
Catalog Numbers
Dimensions (mm)
D
3
4
36
Additional Fuselinks: Quick acting fuselinks in body sized D16, D27, D33 and
D125 rated 2-100A. Reference number suffixed Q, i.e. 10D27Q. Voltage rating 500V.
Gauge rings and keys can also be supplied.
Dimensions (mm)
Figure 1
Figure 2
Data Sheet: 4124
Figure 3
Figure 4
Data Sheet: 4124
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
227
IEC & British Standard Fuses
NH HRC Fuses
Ratings:
___NHG___B
Volts: — 500Vac/250Vdc
— 690Vac/250Vdc
Amps: — 2-1250A
IR: — 120kA
Frequency: — 50Hz
Operating Frequency: — 45-62Hz
Agency Information: IEC 60269, VDE0636, DIN 43620
Part 1 to 4, VDE Mark and CE.
Specifications
Class: gG/gL
Description: DIN
square bodied, dual
indication industrial
fuses.
Construction: Steatite
insulator, corrosionproof (aluminum) metal
parts with full-contact,
silver-plated copper
blades.
Sizes: DIN 000 to 4.
Selectivity Ratio: 1:1.6 up to 500Vac.
Fuse Blocks
SB00-D
SB1-D
SB2-D
Size
000-00
1*, 1
02, 2, 03, 3
Dimensions (mm)
Fuse
Size
000
00
0
01
1
02
2
03
3
4
a1
78.5 ± 1.5
78.5 ± 1.5
125 ± 2.5
135 ± 2.5
135 ± 2.5
150 ± 2.5
150 ± 2.5
150 ± 3
150 ± 3
200
a2
(max)
54
54
68
75
75
75
75
75
75
84
45
45
62
62
62
62
62
62
62
80
a3
± 1.5
± 1.5
+3/-1.5
± 2.5
± 2.5
± 2.5
± 2.5
± 2.5
± 2.5
a4
49 ± 1.5
49 ± 1.5
68 +1.5/-3
68 ± 2.5
68 ± 2.5
68 ± 2.5
68 ± 2.5
68 ± 2.5
68 ± 2.5
90
b
(nom)
15
15
15
15
20
20
25
25
32
50
c1
(± 8)
35
35
35
40
40
48
48
60
60
85
c2
(nom)
10
11
11
11
11
11
11
11
11
11
D
(nom)
2 ± 0.5
7.0 ± 0.5
2.5 ± 0.5
2.5 ± 0.5
2.5 ± 0.5
2.5 ± 0.5
2.5 ± 0.5
2.5 ± 0.5
3.0 ± 0.5
3
e1
(max)
41
48
48
48
53
53
61
61
75
120
e2
(max)
21
30
30
30
52
52
60
60
70
87
e3
(max)
16
25
25
25
25
25
25
25
25
—
Data Sheet 4173
228
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
e4
(nom)
6
6
6
6
6
6
6
6
6
8
f
(max)
8
15
15
15
15
15
15
15
18
30
IEC & British Standard Fuses
NH HRC Fuses
500Vac / 250Vdc
Size
000
00
01
1
02
2
03
3
4
Single Indicator
Slotted End
Tags
2
4
6
10
16
20
25
32
35
40
50
63
80
100
125
160
10
16
20
25
32
35
40
50
63
80
100
125
160
10
16
20
25
32
35
40
50
63
80
100
125
160
200
224
250
35
40
50
63
80
100
125
160
200
224
250
315
355
400
250
315
355
400
500
630
500
630
800
1000
1250
gG/gL Dual Indicator
Voltage Conducting
Carton
Metal Gripping Lugs
Quantity
2NHG000B
4NHG000B
6NHG000B
10NHG000B
16NHG000B
20NHG000B
25NHG000B
32NHG000B
35NHG000B
40NHG000B
50NHG000B
63NHG000B
80NHG000B
100NHG000B
125NHG00B
160NHG00B
10NHG0B
16NHG0B
20NHG0B
25NHG0B
32NHG0B
35NHG0B
40NHG0B
50NHG0B
63NHG0B
80NHG0B
100NHG0B
125NHG0B
160NHG0B
10NHG01B
16NHG01B
20NHG01B
25NHG01B
32NHG01B
35NHG01B
40NHG01B
50NHG01B
63NHG01B
80NHG01B
100NHG01B
125NHG01B
160NHG01B
200NHG1B
224NHG1B
250NHG1B
35NHG02B
40NHG02B
50NHG02B
63NHG02B
80NHG02B
100NHG02B
125NHG02B
160NHG02B
200NHG02B
224NHG02B
250NHG02B
315NHG2B
355NHG2B
400NHG2B
250NHG03B
315NHG03B
355NHG03B
400NHG03B
500NHG3B
630NHG3B
500NHG4G
630NHG4G
800NHG4G
1000NHG4G
1250NHG4G
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
1
1
1
1
1
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
IEC &
British
Fuses
0
Rated
Current
(Amps)
229
IEC & British Standard Fuses
NH HRC Fuses
690Vac / 250Vdc
Size
000
00
0
1
2
3
230
Rated
Current
(Amps)
2
4
6
10
16
20
25
32
35
40
50
63
80
100
6
10
16
20
25
32
35
40
50
63
80
100
50
63
80
100
125
160
200
63
80
100
125
160
200
224
250
315
250
315
355
400
425
500
gG/gL Dual Indicator
Voltage Conducting
Carton
Metal Gripping Lugs
Quantity
2NHG000B-690
4NHG000B-690
6NHG000B-690
10NHG000B-690
16NHG000B-690
20NHG000B-690
25NHG000B-690
32NHG000B-690
35NHG000B-690
40NHG000B-690
50NHG00B-690
63NHG00B-690
80NHG00B-690
100NHG00B-690
6NHG0B-690
10NHG0B-690
16NHG0B-690
20NHG0B-690
25NHG0B-690
32NHG0B-690
35NHG0B-690
40NHG0B-690
50NHG0B-690
63NHG0B-690
80NHG0B-690
100NHG0B-690
50NHG1B-690
63NHG1B-690
80NHG1B-690
100NHG1B-690
125NHG1B-690
160NHG1B-690
200NHG1B-690
63NHG2B-690
80NHG2B-690
100NHG2B-690
125NHG2B-690
160NHG2B-690
200NHG2B-690
224NHG2B-690
250NHG2B-690
315NHG2B-690
250NHG3B-690
315NHG3B-690
355NHG3B-690
400NHG3B-690
425NHG3B-690
500NHG3B-690
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
IEC & British Standard Fuses
NH Fuse Bases
SB*-D, SB*-S
Up to 690V / 160 - 1250A
Sizes 00, 0, 1, 2, 3, 4
Part Numbers
Size
Poles
1
3
160A
0
1
3
160A
1
1
3
Ratings:
2
DIN Screw
Carton Compatible
Quantity Fuse Size
SB00-D
TB00-D
000 & 00
SB0-D
TB0-D
3
1
0
250A
SB1-D
TB1-D
3
1
01 & 1
1
3
400A
SB2-D
TB2-D
3
1
02 & 2
3
1
3
630A
SB3-D
TB3-D
3
1
03 & 3
4
1
1250A
SB4-S (Screw
Connection only)
3
4
• Voltage: up to 690Vac
• Amps: 2 to 1250A
Applications: Protection of industrial circuits and
electrical apparatus
Part Numbers
3
1
00
Description: NH fuse bases with thermoplastic
bodies. DIN rail and screw mounting (size 4 screw
fix). Range of protection accesories for live parts in
order to obtain IP20 protection standard.
Current
(Amps)
TB00-D-IP20
Standards and Approvals: IEC 60269, DIN 43620
Size
Current
(Amps)
Part Ref
NH00
160
SL00
NH0
160
SL0
NH1
250
SL1
NH2
400
SL2
NH3
630
SL3
NH4
1000
SL4
IEC &
British
Fuses
Neutral
Carton
Quantity
3
Fuse extraction handle
Size
Part Ref
Carton
Quantity
C00-3
FEH
1
Protection accessories
Size
Current
(Amps)
NH00*
NH0
NH1
NH2
NH3
160A
160A
250A
400A
630A
Separation Partition
4
Fuse Casing
5
Terminal Cover
1
Separator
3
Part
Ref
Carton
Quantity
Part
Ref
Carton
Quantity
Part
Ref
Carton
Quantity
Part
Ref
Carton
Quantity
SP00*
SP0
SP1-2
SP1-2
SP3
2
2
2
2
2
FC00*
FC0
FC1-2
FC1-2
FC3
3
3
3
3
3
CS00*
CS0
CS1
CS2
CS3
6
6
6
6
6
BC00*
BC0
BC1-2
BC1-2
BC3
2
2
2
2
2
* For single pole only
IP Protection Kits
Microswitch
Part Reference
Description
TB00-D-IP20
Complete triple pole fuse base IP20 rated
FPK0-3P
IP20 kit for TB0-D fuse base
FPK1-3P
IP20 kit for TB1-D fuse base
FPK2-3P
IP20 kit for TB2-D fuse base
FPK3-3P
IP20 kit for TB3-D fuse base
Part Ref
Carton Quantity
BVL-50
1
Microswitch suitable for the following NH Fuse links:
- 400 Volts gG/gL
- 500 Volts gG/gL and aM
- 690 Volts gG/gL and aM
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
231
IEC & British Standard Fuses
Class gG/gL IEC 60269 Industrial Ferrule Fuses
8 x 31mm: 400Vac, 0.5 - 25A
10 x 38mm: 500Vac, 0.5 - 32A
14 x 51mm: 400Vac - 500Vac - 690Vac, 1 - 50A
22 x 58mm: 400Vac - 500Vac - 690Vac, 2 - 125A
232
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
IEC & British Standard Fuses
Class aM IEC Industrial Ferrule Fuses - Class aM IEC
60269
8 x 31mm: 400Vac, 1 - 8A
10 x 38mm: 400Vac - 550Vac, 0.16 - 25A
IEC &
British
Fuses
14 x 51mm: 690Vac - 500Vac, 0.25 - 50A
22 x 58mm: 400Vac - 500Vac - 690Vac, 2 - 125A
Neutral Links
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
233
IEC & British Standard Fuses
Class aM & gG/gL IEC Industrial Ferrule Fuses with
Striker
Class gG/gL with Striker
14 X 51
22 X 58
Catalog Number
With Striker
C14G2S
C14G4S
C14G6S
C14G8S
C14G10S
C14G12S
C14G16S
C14G20S
C14G25S
C14G32S
C14G40S
C14G50S
Catalog Number
With Striker
C22G4S
C22G6S
C22G8S
C22G10S
C22G12S
C22G16S
C22G20S
C22G25S
C22G32S
C22G40S
C22G50S
C22G63S
C22G80S
C22G100S
C22G125S
Amp
Rating
2
4
6
8
10
12
16
20
25
32
40
50
Amp
Rating
4
6
8
10
12
16
20
25
32
40
50
63
80
100
125
Watts Loss
(W)
0.24
0.45
0.42
0.70
0.53
0.88
1.16
1.23
1.46
2.04
3.34
3.04
Watts Loss
(W)
0.48
0.47
0.73
0.74
0.83
1.21
1.29
1.53
2.13
3.40
3.48
4.46
5.86
6.61
8.42
Voltage
(AC)
500
500
400
Voltage
(AC)
690
Interrupting
Rating (kA)
120
120
Interrupting
Rating (kA)
80
690
80
500
500
120
120
400
Class aM with Striker
14 X 51
22 X 58
234
Catalog Number
With Striker
C14M1S
C14M2S
C14M4S
C14M6S
C14M8S
C14M10S
C14M12S
C14M16S
C14M20S
C14M25S
C14M32S
C14M40S
C14M50S
Catalog Number
With Striker
C22M2S
C22M4S
C22M6S
C22M8S
C22M10S
C22M12S
C22M16S
C22M20S
C22M25S
C22M32S
C22M40S
C22M50S
C22M63S
C22M80S
C22M100S
C22M125S
Amp
Rating
1
2
4
6
8
10
12
16
20
25
32
40
50
Amp
Rating
2
4
6
8
10
12
16
20
25
32
40
50
63
80
100
125
Watts Loss
(W)
0.14
0.24
0.45
0.42
0.70
0.53
0.88
1.16
1.23
1.46
2.04
3.34
3.04
Watts Loss
(W)
0.29
0.48
0.47
0.73
0.74
0.83
1.21
1.29
1.53
2.13
3.40
3.48
4.46
5.86
6.61
8.42
Voltage
(AC)
500
500
400
Voltage
(AC)
690
Interrupting
Rating (kA)
120
120
Interrupting
Rating (kA)
80
690
80
500
500
400
120
120
For detailed information, visit the Electrical IEC section at www.cooperbussmann.com
IEC & British Standard Fuses
HRC Fuse Holders
SAFEloc
Specifications
Catalog Symbol:
See table below.
Description: The
CAMaster HRC fuse holder
features a unique
cam-action for easy fuse
removal while allowing
significantly improved
contact pressure between
fuse carrier and base
contact that enhances
electrical performance. A range of lockable safety carriers for
the fuse holder (catalog reference: LSC), are available.
Ratings:
Volts: — 690V
Amps: — 30-100A (See Catalog Number table for details)
Agency Information: CE, CSA C22.2 No. 39; IEC 269
AND BS 88.
Mounting: 35mm DIN-rail or single screw mounting.
Specifications
Catalog
Symbol:
See table below.
Description: The
SAFEloc HRC
fuse holders (for
use with HRCI-CB
fuses) provides a
positive, stressfree fuse fitting
and locks it in position to ensure safe insertion and
withdrawal from the base. Base contacts are fully shrouded
to help protect against electric shock. Shrouds utilize
simple slide/snap action allowing access to the contact
terminal screws.
Ratings:
Volts: — 600V
Amps: — 30-60A (See Catalog Number table for details)
Agency Information: CE, Designed to accommodate the
compact range of offset blade fuse to CSA C22.2 No. 106,
HRCI-CB.
Mounting: 35mm DIN rail or single screw mounting.
Catalog Numbers
Catalog
Numbers
CM20CF
CM30CF
CM60CF
CM100CF
Amp
Ratings
30
30
60
100
Details For:
HRCI-CA Applications
HRCII Applications
Fuse
Accepted
_CIF21
_H07C
_K07C
_K07CR
Accessory Catalog Numbers for CAMaster Units
Catalog
Numbers
20BS
32BS
60/100BS
GLP
NI
20LSC
30LSC
60/100LSC
Amp
Ratings
30
30
60/100
All
All
30
30
60/100A
Data Sheet: 4132
Details
Back Stud
Ganging Link Kit
660V Neon Indicator
Security Carrier with Clip
Fuse Holder
Accepted
CM20CF
CM30CF
CM60/100CF
3-Pole
—
CM20CF
CM30CF
CM60/100CF
Catalog Numbers*
Catalog
Amp
Numbers
Ratings Connection
C30F
Front
C30BS
30
Back
C30FBS
Front-Back
C60F
Front
C60BS
60
Back
C60FBS
Front-Back
*For use with HRCI-CB Fuses.
Fuse
Accepted
_CIF06
EK-Amp
Data Sheet: 4133
For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa
235
IEC &
British
Fuses
CAMaster
236