Power Distribution & Terminal Blocks Section Contents Page Selection table for SCCR PDBs & Power terminal blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Power distribution blocks Series PDBFS enclosed, with high SCCR . . . . . . . . . . . . 295 Series PDB with high SCCR . . . . . . . . . . . . . . . . . . . . . 296 Power terminal blocks Series 163 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297-298 Series 11675 2- to 12-Pole quick-connect . . . . . . . . . . . 299 Series 11725 2- to 4-Pole quick-connect . . . . . . . . . . . . 299 Series 160, 162, 163 & 165 . . . . . . . . . . . . . . . . . . . . . . 299 Series 162, 163 & 165 power stud terminal blocks . . . 300 Series 160, 162, 163 & 165 power splicer blocks . . . . 300 Series 14002 Barrier terminal blocks . . . . . . . . . . . . . . 301 Series 14004 Dead front terminal block . . . . . . . . . . . . 301 Power Distribution & Terminal Blocks 293 Power Distribution & Terminal Blocks Selection Table for SCCR Power Distribution Blocks and Power Terminal Blocks Control Panels. Marking the SCCR on Industrial Control Panels (NEC® 409.110), Industrial Machinery Electrical Panels (NEC® 607.3(A)), and HVAC equipment (NEC® 440.4(B)) is now required by the National Electrical Code. PDBs or PTBs not marked with a SCCR, typically are the weakest link and may limit an assembly to no more than 10kA SCCR. The PDBFS and PDB Series have increased spacing required where used in feeder circuits in equipment listed to UL508A (UL1059 PTBs must be evaluated for proper spacings). Also, for building wiring systems, the PDBFS Series and PDB Series power distribution blocks can be used to meet the new 2008 NEC® requirements in section 376.56(B) for PDBs in wireways. Short-Circuit Current Rated Power Distribution Blocks Cooper Bussmann offers three distinctly different styles of short-circuit current rated power distribution blocks (PDBs) and power terminal blocks (PTBs) to match different application needs. The differences are whether the power distribution blocks are enclosed or not, and whether they are UL1953 Listed PDBs or UL1059 Recognized PTBs, which have different minimum spacing requirements. The table on this page can assist in the selection of the right series for your application requirements. Why these are important? Assembly short-circuit current ratings (SCCRs) are now required in the 2008 NEC® and UL 508A Listed Industrial Selection Table Description High Enclosed SCCR* Spacing** 1” Air 2” Surface Industrial Control Panels UL 508A Branch Circuit Industrial Control Panels UL 508A Feeder Circuit Catalog Page UL Series PDBFS 295 UL 1953 Listed Yes† Yes Yes Yes Series PDB 296 UL 1953 Listed No*** Yes Yes Yes HVAC UL 1995 Wireways NEC® 376.56(B) (Requires UL 1953) Yes Yes Yes Yes Yes Yes w/optional cover † IP20 finger-safe under specific conditions, see datasheet 1149. *When protected by proper fuse class with maximum ampere rating specified or less. ** See PDB Spacing Requirements for Equipment table below. ***Optional covers are available. Not IP20, but provide a safety benefit. ****No, except: Yes, if single pole units installed with proper spacings. PDB & PTB Minimum Spacing Requirements for Equipment UL Standard Spacing between Spacing between live parts of live parts and opposite polarity grounded parts or enclosure Through air Over surface @600V @600V @600V 508A Feeder Circuits 508A Branch Circuits 1995 HVAC 1˝ 2˝ 1˝ 3 1 1 ⁄8˝ 3⁄ ˝ 8 ⁄2˝ 1⁄ ˝ 2 Series PDB ⁄2˝ ⁄2˝ 1 Note: Refer to Specific UL standards for complete spacing details. Series PDBFS Data Sheet: 1049 294 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa Power Distribution & Terminal Blocks Series PDBFS of Power Distribution Blocks Electrical • 600Vac/dc (UL 1953), 690Vac/dc (IEC) • IP20 finger-safe under specific conditions • Short-circuit current ratings up to 200kA, see table • Ampacities up to 760 amps • Cu wire range 14 AWG to 500 kcmil or 2.5 to 240 mm2 Feature/Benefits • Enclosed, safer installation; IP20 finger-safe under specific conditions • High short-circuit current ratings up to 200kA: PDBs do not have to be the weak link in achieving high SCCR for an industrial control panel • Small footprint saves panel space • Listed to UL 1953 which has minimum spacing requirements at 600V of at least 1” through air and 2” over surface required for feeders in UL 508A Industrial Control Panels • For 2D CAD drawings visit www.cooperbussmann.com Mechanical • DIN rail or panel mount; PDBFS330 & PDBFS504 panel mount only • Captive termination screws; screws do not get misplaced • Wire ready: captive termination screws shipped backed out to save time on conductor installations • Sliding DIN rail latch for easy mounting • Single pole, gang mountable for multiple pole applications with interlocking dovetail accessory (optional) • Flammability, UL 94V0 • Tin-plated Al connectors suitable for Cu conductors • Elongated hole for panel mounting; easier mounting with greater flexibility in matching up with drilled panel holes • Part 2A1279: Interlocking dovetail pin accessory One pin interlocks two units, two pins to interlock three units • DIN rail end anchors required to prevent damage to block when torquing Agency/Standards • UL Listed 1953, Guide QPQS, File E256146 • CSA Certified, Class 6228-01, File 15364 • IEC 60947-7-1 • IEC 60529, IP20 (finger-safe) under specific wiring conditions Series PDBFS Terminal Copper Conductor Capability Line Load Configuration Electrical (All Single Pole) Openings per Pole Amps Wire Range Wire Range Line Load Line Load J T RK1 RK5 AWG or kcmil AWG or kcmil LPJ JJS JJN LPS-RK LPN-RK FRS-R FRN-R 2/0 to 8 200 200 100 60 200kA 4 to 12 200 175 200 200 175 200 100 100 100 60 60 60 200kA 100kA 50kA 350 to 6 400 400 200 100 200kA 4 to 8 4 6 to 14 400 200 175 600 600 200 400 200 175 600 600 200 200 100 100 400 400 100 100 30 30 200 200 30 200kA 50kA 100kA 200kA 50kA 50kA 350 600 600 400 200 200kA 300 to 4 600 800* 600 200 100kA 600 500 600 400 to 6 600 800* 800* 600 600 600 400 400 600 200 200kA 100kA 100kA PDBFS204 175A 2/0 to 8 AWG 70 to 10 mm2 2/0 to 8 AWG 70 to 10 mm2 2/0 to 8 PDBFS220 175A 2/0 to 8 AWG 70 to 10 mm2 4 to 14 AWG 25 to 2.5 mm2 2/0 to 8 PDBFS303 310A 350kcmil to 6 AWG 350kcmil to 6 AWG 185 to 16 mm2 185 to 16 mm2 350 to 6 PDBFS330 380A 500kcmil to 6 AWG 240 to 16 mm2 2 to 14 AWG 35 to 2.5 mm2 500 to 6 PDBFS377 570A 300kcmil to 4 AWG 150 to 12 mm2 4 to 14 AWG 25 to 2.5 mm2 PDBFS500 620A 350kcmil to 4 AWG 350kcmil to 4 AWG 185 to 12 mm2 185 to 12 mm2 PDBFS504 760A 500kcmil to 6 AWG 500kcmil to 6 AWG 240 to 16 mm2 240 to 16 mm2 14 2 to 6 300 250 to 4 350 300 to 4 500 400 to 6 8 to 14 SCCR ® Ampacities 75ºC per NEC Table 310.16 and UL 508A Table 28.1 *Class L 800A (KRP-C 800_SP) or less fuses suitable for this particular SCCR case. ** Class G 60A (SC-60) or less or Class CC 30A (LP-CC-30, FNQ-R-30, KTK-R-30) or less are suitable for all SCCRs in this table. Data Sheet: 1049 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 295 Power Distribution & Terminal Blocks Catalog Number Short-Circuit Current Rating Data Conductors Max Fuse Class & Amp** Power Distribution & Terminal Blocks Series PDB of Power Distribution Blocks Electrical • 600Vac/dc (UL 1953) • Short-circuit current ratings up to 200kA, see table • Wire range 14 AWG to 350 kcmil Cu • Spacing between uninsulated opposite polarities or ground meets UL 1953 which requires at least 1” through air and 2” over surface • Ratings available with circuit breakers Feature/Benefits • High short-circuit current ratings up to 200kA. These PDBs do not have to be the weak link in achieving high SCCR for an industrial control panel • Listed to UL 1953 which has minimum spacing requirements at 600V of at least 1” through air and 2” over surface required for feeder in UL 508A Industrial Control Panels • For 2D CAD drawings visit www.cooperbussmann.com Agency/Standards • UL Listed 1953, Guide QPQS, File E256146 Mechanical • Panel mount • Flammability, UL 94V0 • Tin-plated Al connectors suitable for Cu conductors Optional covers Covers are ordered for each individual pole, i.e., three 1-pole covers for 3-pole block, see table A. Except PDB321 blocks have one cover for 1, 2 or 3 pole versions, see table B. Table A Table B Block Cover Block Cover PDB2XX-(pole): CPB162-1 PDB321-1 CPDB-1 PDB3XX-(pole): CPDB-1 PDB321-2 CPDB-2 PDB321-3 CPDB-3 Series PDB Terminal Copper Conductor Capability Line Load Configuration Catalog Number Openings per Pole Amps - Wire Range Wire Range Line Pole Load Short-Circuit Current Rating Data Conductors Max Fuse Class & Amp* Line Load J T RK1 RK5 AWG or kcmil AWG or kcmil LPJ JJS JJN LPS-RK LPN-RK FRS-R FRN-R 2/0 - 8 200 200 200 60 200kA 4 - 12 200 200 175† 175† 200† 200† 200† 100† 100† 60† 60† 60† 200kA 100kA 50kA 200 200 100 60 200kA 400 400† 14 175† 400 4-8 400† 10 - 12 175† 4-8 400 400† 10 - 14 175† 1/0 - 6 400† 400 8 - 12 175† 400 400† 175† 400 400† 175† 400 400† 175† 400 400† 175† 200† 400† 100† 200† 400† 100† 200† 400† 100† 200† 400† 100† 100† 100† 60† 100† 100† 60† 100† 100† 60† 100† 100† 60† 200kA 100kA 100kA 200kA 100kA 100kA 200kA 100kA 100kA 200kA 100kA 100kA PDB204-1 PDB204-3 175A 2/0 - 8 AWG 2/0 - 8 AWG 2/0 - 8 PDB220-1 PDB220-3 175A 2/0 - 8 AWG 4 - 14 AWG 2/0 - 8 PDB280-1 PDB280-3 175A 2/0 - 8 AWG 1/4-20 X 3/4 STUD 2/0 - 8 PDB321-1 PDB321-2 PDB321-3 175A PDB323-1 PDB323-3 2/0 - 8 AWG 4 - 14 AWG 2/0 - 8 310A 300kcmil - 4 AWG 4 - 12 AWG 300 - 4 PDB370-1 PDB370-3 310A 350kcmil - 4 AWG 4 - 14 AWG 350 - 4 PDB371-1 PDB371-3 310A 350kcmil - 4 AWG (6) 2 - 12 AWG (3) 1/0-12 350 - 4 14 Stud 4 -12 Ampacities 75ºC per NEC® Table 310.16 and UL508A Table 28.1 * Class G 60A (SC-60) or less or Class CC 30A (LP-CC-30, FNQ-R-30_SP, KTK-R-30) or less are suitable for all these SCCR in this table. † Higher SCCR may be available, check data sheet 1149. Data Sheet: 1049 296 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa SCCR Power Distribution & Terminal Blocks Series 163 Power Terminal Blocks 163 Series Replaces Cooper Bussmann® 164 Series Specifications Description: Power terminal block. Dimensions: See Dimensions illustrations. Construction: Tin-plated aluminum connectors. Poles: 1- to 3-Poles, See Catalog Numbers table on the following page. Wire Range: See Catalog Numbers table on the following page. Ratings: Volts: — 600Vac/dc Amps: — See catalog Numbers table on the following page. SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, UL Recognized: Guide XCFR2, UL E221592, General Industrial Class per UL1059, CSA Certified: CSA LR15364 Flammability Rating: UL 94V0 Supplied with (4) #4 thread-cutting screws assembled as shown 4.14" Textured surface for marking Power Distribution & Terminal Blocks Dimensions 1-pole 1.96" 2-pole 3.58" CPDB-1 (single pole) CPDB-2 (two pole) CPDB-3 (three pole) 3-pole 5.20" 2.10" 3.72" 5.34" .31" 3.37" 4.00" 0.97" 1.62" 3.25" 3.32" Mtg. hole 0.21 x 0.41, c'bore 0.42 x 0.62 x 0.12 deep (See Following Page for Ratings) Data Sheet: 1049 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 297 Power Distribution & Terminal Blocks Series 163 Power Terminal Blocks Catalog Numbers Basic Catalog Numbers Wire Size (Poles) Lineside (Poles) Loadside Amps/ Pole 16301* 250kcmil-6 AWG Cu Only 250kcmil-6 AWG Cu Only 255 16303 350kcmil-6 AWG Cu-Al 350kcmil-6 AWG Cu-Al 310 16306 500kcmil-6 AWG Cu-Al 500kcmil-6 AWG Cu-Al 380 16321 2/0-14 AWG CU, 2/0-8Al (6)4-14 AWG Cu, 4-8 AWG Al 175 16323 350kcmil-6 AWG Cu-Al (6)4-14 AWG Cu, 4-12 AWG Al 310 16325 (2)2/0-14 AWG Cu, 2/0-8 AWG Al (6)4-14 AWG Cu, 4-8 AWG Al 350 16330 500kcmil-6 AWG Cu-Al (6) 2-14 AWG Cu, 2-12 AWG Al 380 16332 350kcmil-6 AWG Cu-Al (3) 2-14 AWG Cu, 2-8 AWG Al (2) 1/0-14 AWG Cu, 1/0-8 AWG Al 310 16335 500kcmil-6 AWG Cu-Al (3) 2-14 AWG Cu, 2-8 AWG Al (2) 1/0-14 AWG Cu, 1/0-8 AWG Al 380 16370 350kcmil-6 AWG Cu-Al (12)4-14 AWG Cu, 4-12 AWG Al 310 16371 350kcmil-6 AWG Cu-Al (6) 2-14 AWG Cu, 2-8 AWG Al (3) 1/0-14 AWG Cu, 1/0-8 AWG Al 310 16372 350kcmil-6 AWG Cu-Al (21) 10-14 AWG Cu, 10 AWG Al 310 16373 350kcmil-6 AWG Cu-Al (14) 10-14 AWG Cu, 10 AWG Al (3) 1/0-14 AWG Cu-Al 310 16375 600kcmil-2 AWG Cu-Al (12)4-14 AWG Cu, 4-12 AWG Al 420 16376 600kcmil-2 AWG Cu-Al (6) 2-14 AWG Cu, 2-8 AWG Al (3) 1/0-14 AWG Cu, 1/0-8 AWG Al 420 16377 (2)300kcmil-4 AWG Cu-Al (12)4-14 AWG Cu, 4-12 AWG Al 570 16378 500kcmil-6 AWG Cu-Al Stud Size (2) 1/4-20 x 1 380 16383 500kcmil-6 AWG Cu-Al Stud Size (1) 3/8-16 x 1 380 16390 3 ⁄8-16 x 11⁄8 Stud Size 250 16394 1 16395 3 ⁄8-16 x 11⁄8 Stud Size 3 ⁄2-13 x 11⁄16 Stud Size 1 ⁄2-13 x 11⁄16 Stud Size 400 ⁄8-16 x 17⁄16 Stud Size (2) 1⁄4-20 x 9⁄16 Stud Size 310 *Copper connectors for use with copper wire only. Ordering Information 163 Series blocks are available in 1-, 2- or 3-poles. To order: Basic Catalog Number + Number of poles. Examples: 16301-1 = one-pole block 16301-3 = three-pole block Data Sheet: 1049 298 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa Line/Load Power Distribution & Terminal Blocks Power Terminal Blocks Series 11675 Series 160, 162, 163 & 165 Specifications Description: Screw connection line side, (3) 0.250" quick-connect load side power terminal block. Poles: 2- to 12-poles. Wire Range: 8 – 14 AWG Cu. Ratings: Volts: — 250Vac/dc Amps: — Up to 40A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, Guide XCFR2, UL E62622; CSA LR15364. Torque Rating: 9 lb-in max. Catalog Numbers Catalog Numbers 11675-2 11675-3 11675-4 11675-5 11675-6 11675-7 Poles 2 3 4 5 6 7 Catalog Numbers 11675-8 11675-9 11675-10 11675-11 11675-12 Poles 8 9 10 11 12 Specifications Description: Screw connection line side, (4) 0.250" quick-connect load side power terminal block. Poles: 2-, 3- or 4-poles. Wire Range: 2 – 14 AWG Cu/8 AWG Al. Ratings: Volts: — 600Vac/dc Amps: — Up to 70A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, UL Guide XCFR2, E62622; CSA LR15364. Torque Rating: 45 lb-in max. Catalog Numbers Catalog Numbers 11725-2 11725-3 11725-4 Poles 2 3 4 Description: Power terminal blocks. Construction: Molded black thermoplastic. Wire Range: See Catalog Numbers table. Poles: Series 160: 2-, 3- or 4-poles Series 162, 163 and 165: 1-, 2- or 3-poles Ratings: Volts: — 600Vac/dc Amps: — Up to 1520A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, Guide XCFR2, UL E221592 General Industrial Class per UL 1059; CSA Class 6228-01, File 53787. Flammability Rating: UL 94V0. Catalog Numbers Connector Load Material & Ag ency Connection Ampacity Information (6)#4-#14Cu, #4-#8Al 175A UL/CSA (6)#4-#14Cu, #4-#12Al 310A UL/CSA (4)#4-#14Cu, #4-#8Al 175A UL/CSA (6)#4-#14Cu, #4-#8Al 175A UL/CSA (6)#4-#14Cu, #4-#12Al 310A UL/CSA (6)#4-#14Cu, #4-#8Al 350A UL/CSA (6)#2-#14Cu, #2-#12Al 380A UL/CSA (3)#2-#14Cu, #2-#8Al 310A UL/CSA (2)1/0-#14Cu, 1/0-#8Al 16335 500kcmil-#6Cu/Al (3)#2-#14Cu, #2-#8Al 380A UL/CSA (2)1/0-#14Cu, 1/0-#8Al 16370 350kcmil-#6Cu/Al (12)#4-#14Cu, #4-#12Al 310A UL/CSA 16371 350kcmil-#6Cu/Al (6)#2-#14Cu, #2-#8Al 310A UL/CSA (3)1/0-#14Cu, 1/0-#8Al 16372 350kcmil-#6Cu/Al (21)#10-#14Cu, #10Al 310A UL/CSA 16373 350kcmil-#6Cu/Al (3)1/0-#14Cu/Al 310A UL/CSA (14)#10-#14Cu, #10Al 16375 600kcmil-#2Cu/Al (12)#4-#14Cu, #4-#12Al 420A UL/CSA 16376 600kcmil-#2Cu/Al (6)#2-#14Cu, #2-#8Al 420A UL/CSA (3)1/0-#14Cu, 1/0-#8Al 16377 (2)300kcmil-#4Cu/Al (12)#4-#14Cu, #4-#12Al 570A UL/CSA 16400 (4)500kcmil-#6Cu/Al (22)#2-#14Cu/Al 1520A UL/CSA 16528 (2)600kcmil-#2Cu/Al (4)3/0-#6Cu/Al 840A UL/CSA (4)#4-#14Cu/Al 16530 (2)500kcmil-#6Cu/Al (12)#4-#14Cu/Al 760A UL/CSA 16541 (1)500kcmil-#6Cu/Al (21)#6-#14Cu/Al 380A UL/CSA *160 Series Bases have mounting holes outside the barriers. Other bases (162 through 165) have mounting holes within barriers. See Data Sheet for dimensional drawings. Catalog Line Numbers Connection 16021* 2/0-#14Cu, 2/0-#8Al 16023* 350kcmil-#6Cu/Al 16220 2/0-#14Cu, 2/0-#8Al 16321 2/0-#14Cu, 2/0-#8Al 16323 350kcmil-#6Cu/Al 16325 (2)2/0-#14Cu, 2/0-#8Al 16330 500kcmil-#6Cu/Al 16332 350kcmil-#6Cu/Al How To Order Catalog Number + # of Poles Example: 16021 – 3 (complete part number) Optional Covers: 160 162 163 165 Series: Series: Series: Series: CPB160 - (pole) CPB162 - (pole) CPDB- (pole) CPDB165 (1 for each pole) Data Sheets: 1117 (Series 160, 162, 165); 1148 (Series 163) For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 299 Power Distribution & Terminal Blocks Series 11725 Specifications Power Distribution & Terminal Blocks Power Terminal Blocks: Stud & Splicer Series 162, 163 & 165 Series 160, 162, 163 & 165 Specifications Description: Power stud terminal blocks. Construction: Molded black thermoplastic. Poles: 1-, 2- or 3-poles. Wire Range: See Catalog Numbers table. Ratings: Volts: — 600Vac/dc Amps: — Up to 760A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, Guide XCFR2, UL E221592 General Industrial Class per UL 1059; CSA Class 6228-01, File 53787. Flammability Rating: UL 94V0. Specifications Description: Power splicer terminal blocks. Construction: Molded black thermoplastic. Wire Range: See Catalog Numbers table. Poles: Series 160: 2-, 3- or 4-poles Series 162, 163 and 165: 1-, 2- or 3-poles Ratings: Volts: — 600Vac/dc Amps: — Up to 620A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, Guide XCFR2, UL E221592 General Industrial Class per UL 1059; CSA Class 6228-01, File 53787. Flammability Rating: UL 94V0. Stud Block Catalog Numbers Catalog Line Numbers Connection (Poles) Connector to Stud 16280 2/0-#14Cu-Al 16281 2/0-#14Cu-Al 16378 500kcmil-#6Cu-Al 16383 500kcmil-#6Cu-Al 16582 (2)500kcmil-#6Cu-Al Stud to Stud 1 16290 ⁄4-20 x 3⁄4 Stud 3 16390 ⁄8-16 x 11⁄8 Stud 1 16394 ⁄2-13 x 11⁄16 Stud 3 16395 ⁄8-16 x 17⁄16 Stud 3 16591 ⁄8-16 x 17⁄16 Stud 1 16593 ⁄2-13 X 1 Stud Load Connection (Poles) Material & Ampacity Connector Ag ency Information ⁄4-20 X 3⁄4 Stud ⁄4-20 Tapped hole (2)1⁄4-20 x 1 Stud (1)3⁄8-16 x 1 Stud (2)3⁄8-16 x 15⁄8 Stud Al-175A Al-175A Al-380A Al-380A Al-760A UL UL UL UL UL — — CSA CSA CSA ⁄4-20 x 3⁄4 Stud ⁄8-16 x 11⁄8 Stud 1 ⁄2-13 x 11⁄16 Stud (2)1⁄4-20 x 9⁄16 Stud (2)3⁄8-16 x 17⁄16 Stud 1 ⁄2-13 X 1 Stud Cu-175A Cu-250A Cu-400A Cu-310A Cu-400A Cu-600A UL UL UL UL UL UL — CSA CSA CSA CSA CSA 1 1 1 3 Nuts are not supplied with blocks How To Order Catalog Number + # of Poles Example: 16000 – 3 (complete part number) Series: Series: Series: Series: How To Order Catalog Number + # of Poles Example: 16000 – 3 (complete part number) Optional Covers: Optional Covers: 160 162 163 165 Catalog Numbers Connector Catalog Line Load Material & Ag ency Numbers Connection Connection Ampacity Information 16000* 2/0-#8Cu/Al 2/0-#8Cu/Al Al-175A UL 16003* 250kcmil-#6Cu Only 250kcmil-#6Cu Only Cu-255A UL 16005* 350kcmil-#6Cu/Al 350kcmil-#6Cu/Al Al-310A UL 16200 #2-#14Cu, #2-#8Al #2-#14Cu, #2-#8Al Al-115A UL 16201 1/0-#14Cu Only 1/0-#14Cu Only Cu-150A UL 16204 2/0-#8Cu/Al 2/0-#8Cu/Al Al-175A UL 16301 250kcmil-#6Cu Only 250kcmil-#6Cu Only Cu-255A UL/CSA 16303 350kcmil-#6Cu/Al 350kcmil-#6Cu/Al Al-310A UL/CSA 16306 500kcmil-#6Cu/Al 500kcmil-#6Cu/Al Al-380A UL/CSA 16500 (2)350kcmil-#4Cu/Al (2)350kcmil-#4Cu/Al Al-620A UL/CSA 16504 (2)500kcmil-#6Cu/Al (2)500kcmil-#6Cu/Al Al-760A UL/CSA *160 Series Bases have mounting holes outside the barriers. Other bases (162 through 165) have mounting holes within barriers. See Data Sheet for dimensional drawings. CPB160 - (pole) CPB162 - (pole) CPDB - (pole) CPDB165 (1 for each pole) - new style CPB165 - (pole) - old style 160 Series: CPB160 - (pole) 162 Series: CPB162 - (pole) 163 Series: CPDB - (pole) For Short-circuit current rated stud power distribution blocks, go to the Series PDB and Series 162 & 163 with high SCCR. For Short-circuit current rated and/or finger-safe splicer blocks, go to the Series PDBFS, Series PDB or Series 162 & 163 with high SCCR. Data Sheets: 1117 (Series 162, 165); 1148 (Series 163) Data Sheets: 1117 (Series 160, 162, 165); 1148 (Series 163) 300 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa Power Distribution & Terminal Blocks Power Terminal Blocks: Barrier & Dead Front Series 14002 Specifications Description: Barrier terminal block. Poles: 2- to 6-poles. Wire Range: 2 – 14 AWG Cu/8 AWG Al. Ratings: Volts: — 600Vac/dc Amps: — 115A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, Guide XCFR2, UL E62622; CSA LR15364. Torque Ratings*: 2-3, 50 lb-in; 4-6, 45 lb-in; 8, 40 lb-in; 10-14, 35 lb-in. *Consult factory for torque ratings for CP and Q options. Marking: Marking strip optional, consult factory. Options For Load Side Connector CP: Sems pressure plate, rated 60A, 600V Q: Quick-Connect, rated 50A, 600V To order options, enter letter code in front of Catalog Number: i.e., CP14002-2. Catalog Numbers Poles 2 3 4 Catalog Numbers 14002-5 14002-6 Poles 5 6 Power Distribution & Terminal Blocks Catalog Numbers 14002-2 14002-3 14002-4 Series 14004 Specifications Description: Dead front terminal block. Poles: 2 to 12 poles. Wire Range: 4 – 14 AWG Cu/8 AWG Al. Ratings: Volts: — 600Vac/dc Amps: — 90A SCCR:— 10kA per UL 508A table SB4.1 Agency Information: CE, Guide XCFR2, UL E62622; CSA LR15364. Marking: Marking strip optional, consult factory. Catalog Numbers Catalog Numbers 14004-2 14004-3 14004-4 14004-5 14004-6 14004-7 Poles 2 3 4 5 6 7 Catalog Numbers 14004-8 14004-9 14004-10 14004-11 14004-12 Poles 8 9 10 11 12 For product data sheets, visit www.cooperbussmann.com/datasheets/ulcsa 301 302