Epoxy-Dipped Radial Lead Inductive Film/Foil Capacitors UMR • Coupling • Ceramic Disk Alternative • Blocking • Bypass Operating Temperature Range -55°C to 85°C Capacitance Tolerance ±10% at 1kHz, 25°C WVDC 100 VAC 63 Voltage Range 1.0% at 1 kHz, 25°C Dissipation Factor 30,000 MΩ Insulation Resistance 2,000 hours, +85°C with 125% rated DC voltage Load Life Capacitance Change ≤8% maximum Dissipation Factor Change <110% maximum specification Insulation Resistance ≥ 4,500 MΩ 250 hours, 95% RH, 25°C and no applied voltage Capacitance Change Humidity Test Dissipation Factor Change Insulation Resistance <10% of initial readings @ +25°C, 1kHz ≤ 10% of initial +25°C 1kHz ≥ Minimum 2700MΩ Self-inductance ≤1 nH/mm along the capacitor pitch Capacitance Drift Factor (after 2 years) ≤ 3.0% up to 40°C Capacitance Temperature Coefficient +500 ppm/°C, ± 200ppm/°C Type Inductive film/foil Dielectric Polyester film Electrodes Aluminum foil Leads Tinned copper wire Coating Flame retardant epoxy sealed resin (UL 94V-O) ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com Epoxy-Dipped Radial Lead Inductive Film/Foil Capacitors UMR STANDARD PART LISTING Capacitance (µF) PART NUMBER WVDC dv/dt (v/µ s) L Max. H Max. T Max. S Lead Spacing d Lead Wire Diameter .001 100 102UMR100K 10 5.5 10.5 3.0 3.5 0.5 .0015 100 152UMR100K 10 5.5 10.5 3.0 4.0 0.5 .0022 100 222UMR100K 10 5.5 10.5 3.0 4.0 0.5 .0033 100 332UMR100K 10 5.5 10.5 3.0 4.0 0.5 .0039 100 392UMR100K 10 5.5 10.5 3.0 4.0 0.5 .0047 100 472UMR100K 10 5.5 10.5 3.0 4.0 0.5 .0056 100 562UMR100K 10 5.5 10.5 3.0 4.0 0.5 .0068 100 682UMR100K 10 5.5 10.5 3.0 4.0 0.5 .01 100 103UMR100K 10 6.5 10.5 3.0 5.0 0.5 .015 100 153UMR100K 10 6.5 11.5 3.0 5.0 0.5 .022 100 223UMR100K 10 6.5 11.5 3.5 5.0 0.5 .033 100 333UMR100K 10 7.5 11.5 3.5 6.5 0.5 .047 100 473UMR100K 10 7.5 12.5 4.5 6.5 0.5 .056 100 563UMR100K 10 9.0 12.5 4.5 7.0 0.5 .068 100 683UMR100K 10 9.0 12.5 4.5 7.0 0.5 .1 100 104UMR100K 10 10.0 12.5 5.5 7.5 0.5 .15 100 154UMR100K 10 12.5 18.5 6.0 8.5 0.5 .22 100 224UMR100K 10 12.5 18.5 6.0 8.5 0.6 .33 100 334UMR100K 10 15.0 19.5 8.0 9.5 0.6 .47 100 474UMR100K 10 18.5 19.5 11.5 10.0 0.6 Convert to inches, divide by 25.4 L max. T max. H max. 1.5 max. 15.0 min. S±1.0 d±.05 ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com UMR Epoxy-Dipped Radial Lead Inductive Film/Foil Capacitors Ω ENVIRONMENTAL/ENDURANCE DATA ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com Epoxy-Dipped Radial Lead Inductive Film/Foil Capacitors UMR RADIAL LEAD TAPING SPECIFICATIONS GENERAL SPECIFICATIONS FORMED LEAD TAPING FILM CAPACITORS FILM CAPACITORS BODY SIZE: Maximum Body Length (L): 10.5 mm Minimum Body Height (Hc): 12.5 mm Maximum Body Thickness (T): 6.5 mm INTERRUPTION OF SEQUENCE: No consecutive capacitors may be absent. Empty spaces < 0.1% of package quantity. SPLICES: Spliced tape strength is equal to non-spliced tape Splice thickness is ≤ 4 single tape layers Splice offset ± .3mm REFERENCE STANDARD: EIA RS 468A T L P2 ∆ P Hc F H P1 Ho C W2 L1 TAPE REFERENCE DIMENSIONS W1 W0 Carrier Width (W) 18.0 ±0.5 Capacitor Bottom to Feed Hole (H) 20.0 ±.75 Height of Seating Plane (Formed Lead) H0 16.0 ±0.5 Lead Spacing: (Formed) (F) 5.0 ±0.5 Capacitor Pitch (P) 12.7 ±1.00 Sprocket Hole Pitch (P0) 12.7 ±0.30 Sprocket Hole Dia. (F) 4.0 ±0.30 0 ±1.00 Case Top to Feed Hole (H1) 32.0 Max. Sprocket Hole to First Lead (P1) 3.85 ±.70 Lead Extension (I) 2.2 Max. Component Tape Width (C) 43.2 Max. Cut Out Length (L1) 11.0 Max. Sprocket Hole Position (W1) 9.0 ±0.5 Front Back Alignment (∆) W F Po AMMO PACKAGING H QUANTITIES PER BOX Capacitance (µF) Ammo .001- .0082 3,500 .010 - .012 3,000 .015 - .027 3,000 .032 - .047 2,000 .056 - .068 1,500 .082 - .1 1,000 Do dØ L T BOX DIMENSIONS mm L H T (max) (max) (max) 340 360 65 ® 3757 W. Touhy Ave., Lincolnwood, IL 60712 • (847) 675-1760 • Fax (847) 673-2850 • www.illcap.com