MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC−8 CASE 751AZ ISSUE B 8 1 SCALE 1:1 DATE 18 MAY 2015 0.10 C D NOTES 4&5 45 5 CHAMFER D h NOTE 6 D A 8 H 2X 5 0.10 C D E E1 NOTES 4&5 L2 1 0.20 C D L C DETAIL A 4 8X B NOTE 6 TOP VIEW b 0.25 M C A-B D NOTES 3&7 NOTE 7 0.10 C e A1 C SIDE VIEW NOTE 8 DIM A A1 A2 b c D E E1 e h L L2 DETAIL A A2 A SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.004 mm IN EXCESS OF MAXIMUM MATERIAL CONDITION. 4. DIMENSION D DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006 mm PER SIDE. DIMENSION E1 DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.010 mm PER SIDE. 5. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOT TOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE OUTER MOST EXTREMES OF THE PLASTIC BODY AT DATUM H. 6. DIMENSIONS A AND B ARE TO BE DETERMINED AT DATUM H. 7. DIMENSIONS b AND c APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10 TO 0.25 FROM THE LEAD TIP. 8. A1 IS DEFINED AS THE VERTICAL DISTANCE FROM THE SEATING PLANE TO THE LOWEST POINT ON THE PACKAGE BODY. c END VIEW SEATING PLANE RECOMMENDED SOLDERING FOOTPRINT* MILLIMETERS MIN MAX --1.75 0.10 0.25 1.25 --0.31 0.51 0.10 0.25 4.90 BSC 6.00 BSC 3.90 BSC 1.27 BSC 0.25 0.41 0.40 1.27 0.25 BSC GENERIC MARKING DIAGRAM* 8X 0.76 8 XXXXX ALYWX G 8X 1.52 1 7.00 XXXXX A L Y W G 1 1.27 PITCH DIMENSIONS: MILLIMETERS *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G”, may or not be present. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: STATUS: 98AON34918E ON SEMICONDUCTOR STANDARD REFERENCE: © Semiconductor Components Industries, LLC, 2002 October, DESCRIPTION: 2002 − Rev. 0 SOIC−8 = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package http://onsemi.com 1 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. Case Outline Number: PAGE 1 OFXXX 2 DOCUMENT NUMBER: 98AON34918E PAGE 2 OF 2 ISSUE REVISION DATE O RELEASED FOR PRODUCTION FROM POD #6000209 TO ON SEMICONDUCTOR. REQ. BY B. BERGMAN. 19 SEP 2008 A CORRECTED DIMENSIONS NOTE FROM MILLIMETERS TO INCHES. REQ. BY J. LETTERMAN. 25 NOV 2014 B REDREW DRAWING TO JEDEC STANDARDS AND ADDED SOLDER FOOTPRINT. REQ. BY F. KOLANKO. 18 MAY 2015 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. © Semiconductor Components Industries, LLC, 2015 May, 2015 − Rev. B Case Outline Number: 751AZ