NLX2G04 Dual Inverter The NLX2G04 MiniGatet is an advanced high−speed CMOS dual inverter in ultra−small footprint. The NLX2G04 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. http://onsemi.com Features High Speed: tPD = 1.8 ns (Typ) @ VCC = 5.0 V Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C Power Down Protection Provided on inputs Balanced Propagation Delays Overvoltage Tolerant (OVT) Input and Output Pins Ultra−Small Packages These are Pb−Free Devices MARKING DIAGRAMS GND 6 5 2 3 IN A2 4 M M L 1 E 1 IN A1 M M 2 ULLGA6 1.2 x 1.0 CASE 613AE M Q 1 Q ULLGA6 1.0 x 1.0 CASE 613AD Q • • • • • • • M OUT Y1 VCC ULLGA6 1.45 x 1.0 CASE 613AF UDFN6 1.0 x 1.0 CASE 517BX UDFN6 1.2 x 1.0 CASE 517AA 1 OUT Y2 1 Figure 1. Pinout (Top View) 1 IN A1 1 OUT Y1 IN A2 1 OUT Y2 UDFN6 1.45 x 1.0 CASE 517AQ 1 Figure 2. Logic Symbol Q M PIN ASSIGNMENT = Device Marking = Date Code 1 IN A1 2 GND ORDERING INFORMATION 3 IN A2 See detailed ordering and shipping information on page 5 of this data sheet. 4 OUT Y2 5 VCC 6 OUT Y1 FUNCTION TABLE A Y L H H L © Semiconductor Components Industries, LLC, 2014 December, 2014 − Rev. 3 1 Publication Order Number: NLX2G04/D NLX2G04 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage −0.5 to +7.0 V VIN DC Input Voltage −0.5 to +7.0 V DC Output Voltage −0.5 to +7.0 V VIN < GND −50 mA VOUT < GND −50 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current Per Supply Pin ±100 mA IGND DC Ground Current per Ground Pin ±100 mA TSTG Storage Temperature Range −65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C MSL FR ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in Latchup Performance Above VCC and Below GND at 125 °C (Note 2) ±500 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V −55 +125 °C 0 0 0 20 10 5 ns/V VOUT TA Operating Free−Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. http://onsemi.com 2 NLX2G04 DC ELECTRICAL CHARACTERISTICS VCC (V) Min Typ TA = +855C Max Min Max TA = −555C to +1255C Min Max Symbol Parameter VIH Low−Level Input Voltage 1.65−1.95 0.75 x VCC 0.75 x VCC 0.75 x VCC 2.3 to 5.5 0.70 x VCC 0.70 x VCC 0.70 x VCC Low−Level Input Voltage 1.65−1.95 0.25 x VCC 0.25 x VCC 0.25 x VCC 2.3 − 5.5 0.30 x VCC 0.30 x VCC 0.30 x VCC VIL VOH VOL High− Level Output Voltage Low−Level Output Voltage Conditions TA = 25 5C VIN = VIH or VIL IOH = −100 mA VIN = VIH or VIL IOH = −4 mA IOH = −8 mA IOH = −12 mA IOH = −16 mA IOH = −24 mA IOH = −32 mA VIN = VIH or VIL IOL = 100 mA 1.65 − 5.5 VCC− 0.1 VCC VCC− 0.1 VCC− 0.1 1.65 2.3 2.7 3.0 3.0 4.5 1.29 1.9 2.2 2.4 2.3 3.8 1.52 2.1 2.4 2.7 2.5 4.0 1.29 1.9 2.2 2.4 2.3 3.8 1.29 1.9 2.2 2.4 2.3 3.8 1.65 − 5.5 Unit V V V 0.1 0.1 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 V VIN = VIH or VIL IOH = −4 mA IOH = −8 mA IOH = −12 mA IOH = −16 mA IOH = −24 mA IOH = −32 mA 1.65 2.3 2.7 3.0 3.0 4.5 Input Leakage Current 0 v VIN v 5.5 V 0 to 5.5 ±0.1 ±1.0 ±1.0 mA IOFF Power−Off Output Leakage Current VIN or VOUT = 5.5 V 0 1.0 10 10 mA ICC Quiescent Supply Current 0 v VIN v VCC 5.5 1.0 10 10 mA IIN 0.08 0.2 0.22 0.28 0.38 0.42 Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. http://onsemi.com 3 NLX2G04 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 nS) Symbol tPLH, tPHL Parameter Propagation Delay, Input A to Output Y VCC (V) Test Condition 1.65 TA = −555C to +1255C TA = 25 5C Min Typ Max Min Max Unit RL = 1 MW, CL = 15 pF 1.8 2.3 9.2 1.8 11 ns 1.8 RL = 1 MW, CL = 15 pF 1.8 4.4 7.6 1.2 8.4 2.3−2.7 RL = 1 MW, CL = 15 pF 1.2 3.0 5.1 1.2 5.6 3.0−3.6 RL = 1 MW, CL = 15 pF 0.8 2.2 3.4 0.8 3.8 RL = 500 W, CL = 50 pF 1.2 2.9 4.5 1.2 5.0 RL = 1 MW, CL = 15 pF 0.5 1.8 2.8 0.5 3.1 RL = 500 W, CL = 50 pF 0.8 2.3 3.6 0.8 4.0 4.5−5.5 CIN Input Capacitance 5.5 VIN = 0 V or VCC 2.5 pF CPD Power Dissipation Capacitance (Note 3) 3.3 5.5 10 MHz VIN = 0 V or VCC 9 11 pF 3. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no−load dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC. http://onsemi.com 4 NLX2G04 VCC A or B 50% GND tPLH Y tPHL 50% VCC Figure 3. Switching Waveforms VCC PULSE GENERATOR DUT RT CL RL RT = ZOUT of pulse generator (typically 50 W) Figure 4. Test Circuit ORDERING INFORMATION Package Shipping† NLX2G04AMX1TCG ULLGA6, 1.45 x 1.0, 0.5P (Pb−Free) 3000 / Tape & Reel NLX2G04BMX1TCG ULLGA6, 1.2 x 1.0, 0.4P (Pb−Free) 3000 / Tape & Reel NLX2G04CMX1TCG ULLGA6, 1.0 x 1.0, 0.35P (Pb−Free) 3000 / Tape & Reel NLX2G04MUTCG (In Development) UDFN6, 1.2 x 1.0, 0.4P (Pb−Free) 3000 / Tape & Reel NLX2G04AMUTCG UDFN6, 1.45 x 1.0, 0.5P (Pb−Free) 3000 / Tape & Reel NLX2G04CMUTCG UDFN6, 1.0 x 1.0, 0.35P (Pb−Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 5 NLX2G04 PACKAGE DIMENSIONS UDFN6, 1.2x1.0, 0.4P CASE 517AA ISSUE D EDGE OF PACKAGE PIN ONE REFERENCE 2X 0.10 C ÉÉ ÉÉ ÉÉ L1 E DETAIL A Bottom View (Optional) TOP VIEW 2X EXPOSED Cu 0.10 C (A3) 0.10 C A1 A 10X 0.08 C MOLD CMPD ÉÉÉ ÉÉÉ DETAIL B Side View (Optional) SEATING PLANE SIDE VIEW A3 DIM A A1 A3 b D E e L L1 L2 MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.127 REF 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.30 0.40 0.00 0.15 0.40 0.50 MOUNTING FOOTPRINT* 6X 6X 0.42 0.22 C A1 5X 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A B D L 3 L2 6X 0.40 PITCH b 0.10 C A B 0.05 C 6 4 DIMENSIONS: MILLIMETERS e NOTE 3 BOTTOM VIEW 1.07 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 NLX2G04 PACKAGE DIMENSIONS UDFN6 1.45x1.0, 0.5P CASE 517AQ ISSUE O A B D PIN ONE REFERENCE 0.10 C L1 ÉÉÉ ÉÉÉ DETAIL A E DIM A A1 A2 b D E e L L1 ÉÉ ÉÉ EXPOSED Cu DETAIL B MOLD CMPD DETAIL B 0.05 C 6X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. OPTIONAL CONSTRUCTIONS TOP VIEW 0.10 C L L OPTIONAL CONSTRUCTIONS A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.07 REF 0.20 0.30 1.45 BSC 1.00 BSC 0.50 BSC 0.30 0.40 −−− 0.15 MOUNTING FOOTPRINT 0.05 C A1 A2 SIDE VIEW e 6X C 6X SEATING PLANE L 1.24 3 1 DETAIL A 6X 0.53 6 0.30 PACKAGE OUTLINE 4 BOTTOM VIEW 6X 0.50 PITCH DIMENSIONS: MILLIMETERS b 0.10 C A B 0.05 C 1 NOTE 3 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 NLX2G04 PACKAGE DIMENSIONS UDFN6 1.0x1.0, 0.35P CASE 517BX ISSUE O PIN ONE REFERENCE NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D ÉÉÉ ÉÉÉ ÉÉÉ E 0.10 C 2X 2X 0.10 C DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 0.05 C SIDE VIEW A1 C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 5X e 5X 0.48 L 6X 0.22 3 1 L1 1.18 6 4 BOTTOM VIEW 6X b 0.10 M C A B 0.05 M C 0.53 1 PKG OUTLINE NOTE 3 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 NLX2G04 PACKAGE DIMENSIONS ULLGA6 1.0x1.0, 0.35P CASE 613AD ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 5X 0.48 6X 0.22 e 5X L NOTE 4 3 1 1.18 L1 0.53 6 4 6X b 0.05 C 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 9 NLX2G04 PACKAGE DIMENSIONS ULLGA6 1.2x1.0, 0.4P CASE 613AE ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.35 0.45 5X 0.49 e 5X L 6X 0.26 NOTE 4 3 1 1.24 L1 6 4 0.53 6X b 0.10 C A B BOTTOM VIEW 0.05 C NOTE 3 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 NLX2G04 PACKAGE DIMENSIONS ULLGA6 1.45x1.0, 0.5P CASE 613AF ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉ ÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C MILLIMETERS MIN MAX −−− 0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 A 6X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 5X C A1 e 5X L 0.49 NOTE 4 3 1 6X 0.30 1.24 L1 0.53 6 4 BOTTOM VIEW 6X b 0.10 C A B 0.05 C 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLX2G04/D