N Style Coaxial Connector N Series FEATURE Characteristic Impedance ・ N series is a thread coupling coaxial connector which is the most popular as a 7mm type 50 Ω 50 Ω impedance. ・ N series is available for various cable type. Frequency Range ・ It is incompatible to NC series(75 Ω impedance N DC to 3GHz Style connector). Lock Type Screw CONFORMING STANDARD JIS-C5411,MIL-PRF-39012 SPECIFICATIONS Characteristic Impedance 50 Ω Dielectric Withstanding Voltage 1,500V AC(r.m.s) / 1 minute Insulation Resistance 1,000M Ω min. at 500V DC Contact Resistance 3m Ω max. V.S.W.R. 1.3 max. (DC ∼ 3GHz) ＊ The specifications are typical but may not apply to all connectors. Please check the specifications on each item with its drawing from us when you use. Also, the performance is diffrenet by using cable. RoHS MATERIAL/FINISH Compliant Compliant Item Material / Finish Shell Copper Alloy / Ni or Ag Plating Contact (Female) Copper Alloy / Ag or Au Plating Contact (Male) Copper Alloy /Ag or Au Plating Insulator PTFE Gasket Silicon Rubber ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 111021 http://www.ddknet.co.jp N Series Unit：mm ○ Straight Cable Plug Clamp Type Applicable Part Number Cable 3C-2V φA φ21 N-P-3-CF 3D-2V 3C-2V N-P-3-Ni-CF 3D-2V 3C-2V N-P-3-NiCAu-CF 3D-2V （L） 3C-2W N-P-3W-CF 3D-2W 3C-2W N-P-3W-Ni-CF 3D-2W 3C-2W φA φ21 N-P-3W-D1-CF 3D-2W Finish φA （L）Outer Center Assembly Instruction Conductor Conductor 6.2 44.6 Ag Ag 1 6.2 44.6 Ni Ag 1 6.2 44.6 Ni Au 1 7.2 44.6 Ag Ag 1 7.2 44.6 Ni Ag 1 7.2 44.6 Ni Au 1 N-P-55U-CF RG-55/U 5.4 44.6 Ag Ag 1 N-P-55U-Ni-CF RG-55/U 5.4 44.6 Ni Ag 1 N-P-58U-CF RG-58/U 5.4 44.6 Ag Ag 1 N-P-58U-Ni-1-CF RG-58/U 5.4 44.6 Ni Ag 1 N-P-58U-NiCAu-CF RG-58/U 5.4 44.6 Ni Au 1 Applicable Part Number Cable 3.5D-FE N-SP-3.5DFE-CF Au ー 8.6 44.0 Ag Ag 1 8.6 44.0 Ni Ag 1 9.1 45.0 Ag Ag 1 9.1 45.0 Ni Ag 1 9.1 45.0 Ni Au 1 5D-FB 8.1 44.0 Ni Ag 1 5D-SFA 8.6 41.5 Ni Au ー 11.2 44.0 Ag Ag 1 11.2 44.0 Ni Ag 1 11.25 38.0 Ag Ag 2 5C-2V 5D-2V 5C-2W N-P-5W-CF 5D-2W 5C-2W N-P-5W-Ni-CF 5D-2W 5C-2W N-P-5W-NiCAu-CF 5D-2W N-P-5DFB-1-CF N-SP-5DSFA-CF RG-8/U N-P-8U-CF RG-9/U RG-8/U N-P-8U-Ni-CF RG-9/U RG-8/U UG-21D/U-CF Conductor Conductor Ni 5D-2V N-P-5-Ni-CF RG-9/U ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 2 Assmbly Instruction 41.5 5C-2V N-P-5-CF Center 6.2 3.5D-QEFA （L） Finish φA （L）Outer N Series Unit：mm ○ Straight Plug Clamp Type φA φ21 Part Number （38.0） φ21 φA Cable Finish φA Center Outer Assembly Instruction Conductor Conductor N-P-8-1-CF 8D-2V 12.6 Ag Ag 4 N-P-8-1-Ni-CF 8D-2V 12.6 Ni Ag 4 N-P-8DFB-1-CF 8D-FB 11.8 Ni Ag ー Part Number N-P-10-CF N-P-Ni-CF （51.7） Applicable N-P-10DFB-1-CF Finish Applicable φA Outer Cable Assembly Instruction Center Conductor Conductor 10C-2V 10D-2V 10C-2V 10D2V 10D-FB 14.2 Ag Ag 4 14.2 Ni Ag 4 14.2 Ni Ag 4 φA φ21 Crimp Type Part Number N-P-3D2V-CR20-CF （L） N-P-5D2V-CR20-CF Applicable Cable 3D-2V 3D-LFV 5D-2V Finish φA （L） Outer Crimp Tool 7.1 35.0 Ni Ag 6 CR-H-1152 9.5 37.2 Ni Ag 7 CR-H-1130 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 3 Assembly Instruction Conductor Conductor Above drawing is N-P-5D2V-CR20-CF. http://www.ddknet.co.jp Center N Series Unit：mm ○ Right Angle Cable Plug Clamp Type φ21 Applicable Cable Finish φA (L1)（L2）Outer Center Assembly Instruction Conductor Conductor N-LP-58U-CF RG-58/U 5.4 52.9 36.6 Ag Ag ー N-LP-58U-Ni-CF RG-58/U 5.4 52.9 36.6 Ni Ag ー φA φ17.5 (L2) Part Number （L1） φ21 φA (L2) Part Number Applicable Cable Finish φA （L1）(L2) Outer Center Conductor Conductor N-LP-5-CF 5D-2V 8.6 53.0 36.6 Ag Ag ー N-LP-5-Ni-CF 5D-2V 8.6 53.0 36.6 Ni Ag ー （L1） φ21 Part Number Cable RG-9/U (34.9) φ11.2 Applicable RG-8U N-LP-8U-CF φ17.5 Assembly Instruction N-LP-8U-Ni-CF RG-8U RG-9/U Finish Outer Ag Ag ー Ni Ag ー ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 4 Assembly Instruction Conductor Conductor （47.0） http://www.ddknet.co.jp Center N Series Unit：mm ○ Straight Cable Jack Clamp Type Applicable Cable φA Part Number 3C-2V N-J-3-CF 3D-2V （46） 3C-2V N-J-3-Ni-CF 6.2 Ag Ag 2 6.2 Ni Ag 2 5.4 Ag Ag 2 N-J-58U-Ni-CF RG-58/U 5.4 Ni Ag 2 Applicable Cable N-J-5-Ni-CF N-J-8U-CF N-J-8U-Ni-CF φB φA Part Number N-J-8-1-CF （L） Conductor Conductor RG-58/U N-J-5-CF （L） Assembly Instruction Center N-J-58U-CF Part Number φA 3D-2V Finish φA Outer N-J-8-1-Ni-CF UG-23D/U-CF N-J-10-CF （52.7） N-J-10-Ni-CF N-J-10DFB-1-CF (L) Outer Assembly Instruction Center Conductor Conductor 5D-2V 8.6 47.0 Ag Ag 2 5D-2V 8.6 47.0 Ni Ag 2 11.2 47.0 Ag Ag 2 11.2 47.0 Ni Ag 2 RG-8/U RG-9/U RG-8/U RG-9/U Applicable Finish φB 8D-2V 12.7 19.1 41.2 Ag Ag 5 8D-2V 12.7 19.1 41.2 Ni Ag 5 11.2 19.0 40.0 Ag Ag 5 Cable RG-8/U RG-9/U (L) Outer Assembly Instruction φA Cable 10C-2V 10D-2V 10C-2V 10D-2V 10D-FB Finish φA φB Outer 5 Center Assembly Instruction Conductor Conductor 14.2 22.2 Ag Ag 5 14.2 22.2 Ni Ag 5 14.2 22.2 Ni Ag 5 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp Center Conductor Conductor Applicable φB φA Part Number Finish φA N Series Unit：mm ○ Straight Panel Cable Jack 4-φ3.2 B 2.0 N-PJ-3-CF C （46） 18.2 0.05 +0.1 4-φ3.2 0 +0.1 φ17.8 0 Cable Finish φA B C Outer Assembly Instruction Center Conductor Conductor 3D-2V N-PJ-3-Ni-CF □25.4 Applicable 3C-2V C φ17.5 φA Part Number 3C-2V 3D-2V 6.2 16.7 18.2 Ag Ag 3 6.2 16.7 18.2 Ni Ag 3 Ag Ag 3 N-PJ-55U-CF RG-55/U 5.4 16.6 18.2 N-PJ-55U-Ni-CF RG-55/U 5.4 16.6 18.2 Ni Ag 3 N-PJ-58U-CF RG-58/U 5.4 16.6 18.2 Ag Ag 3 N-PJ-58U-Ni-CF RG-58/U 5.4 16.6 18.2 Ni Ag 3 18.2 0.05 Panel Mounting Dimensions 4-φ3.2 C Part Number D φB φA 2.0 Applicable Cable 5C-2V N-PJ-5-CF 5D-2V N-PJ-5-Ni-CF 5D-2V Finish φA B 18.24 Ag Ag 3 8.6 17.5 16.7 18.24 Ni Ag 3 18.24 0.05 Panel Mounting Dimensions ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 6 Assembly Instruction 16.7 18.24 0.05 http://www.ddknet.co.jp Center 17.5 +0.1 +0.1 Outer 8.6 4-φ3.2 0 φ18.0 0 D Conductor Conductor D □25.4 （47） C N Series Unit：mm ○ Receptacle Jack 4-φA Finish Part Number L Outer Center φA 18.2 φ14.6 Conductor Conductor N-R-CF 2 18.2 18.7 29 Ag Ag φ 3.2 N-R-Ni-CF 29 Ni Ag φ 3.2 N-R-NiCAu-CF 29 Ni Au φ 3.2 UG-58A/U-CF 29 Ag Ag φ 3.2 □25.4 L +0.1 18.2 0.05 4-φ3.2 0 +0.1 φ15.0 0 18.2 0.05 Panel Mounting Dimensions ○ Dust Cap 5/8-24UNEF-2B （φ3.5） (φ19.5) Part Number （60） Finish N-RC-5 Ni N-RC-5-D1 Ag （71） 5/8-24UNEF-2B Part Number (φ19.3) N-RC-3-CF 11.1 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 7 Finish Ni N Series Unit：mm ○ Assembly Instruction(1) Straight Cable Plug Parts Configulration Contact Nut Washer Gasket Ring Clamp Insulator Body ① L=The Cable length require for the single-ended ① cable assembly. L=L1-10 L1 Sheath Outer Conductor ② Insert the nut, washer and gasket into the cable. Cut the sheath 15mm from the end of the cable ② and insert the clamp. Please be careful to not damage the outer conductor. 15mm Nut Washer Gasket Clamp Pick the outer conductor and turn down to the clamp equally. Insulator ③ Pick the outer conductor and turn down to the clamp. Cut the outer conductor along the clamp. ③ Canter Conductor （Pre-soldering） Cut the insulator and center conductor as fig.3. Please be careful to not damage the center conductor. 5.0mm 3.5∼4.0mm 3.5mm ④ Solder up the contact with the center conductor. ④ Soldering Contact No gap Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. ⑤ Insert the ring and insulator as fig. 5. ⑤ Ring Insulator ⑥ Insert the above assembly into the body and screw up by wrench. ⑥ ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 8 N Series Unit：mm ○ Assembly Instruction(2) Straight Cable Jack Parts Configulration Washer Clamp Washer Insulator Contact Gasket Nut Body ① L=The Cable length require for the single-ended cable assembly. ① L=L1-12 L1 Nut Gasket Outer Conductor ② Insert the nut, washer and gasket into the cable. Cut the sheath 15mm from the end of the cable ② and insert the calmp. Please be careful to not damage the outer conductor . Cable 15mm Washer Insulator Center Conductor （Pre-soldering） ③ Pick the outer conductor and turn down to the ③ clamp. Cut the outer conductor along the clamp. Cut the insulator and center conductor as fig.3. Clamp 3.5∼4mm Please be careful to not damage the center 3.5mm Soldering conductor. 5mm Contact ④ Solder up the contact with the center conductor. ④ Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. No gap Washer ⑤ Inser the washer and insulator as fig.5. ⑤ Insulator ⑥ Insert the above assembly into the body and screw up by wrench. ⑥ ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 9 N Series Unit：mm ○ Assmbly Instruction(3）Straight Panel Jack Parts Configulration Body Insulator Contact Gasket Nut Washer Clamp Washer ① L=The Cable length require for the single-ended ① cable assembly. L=L1-6.7 L1 L=-L2-1.2 L2 Nut Gasket Outer Conductor ② Insert the nut, washer and gasket into the cable. ② Cut the sheath 15mm from the end of the cable and insert the clamp. Please be careful to not damage the outer 15mm Cable conductor. Washer Insulator Center Conductor ③ Pick the outer conductor and turn down to the （Pre-soldering) ③ clamp. Cut the outer conductor along the clamp. Cut the insulator and center conductor as fig.3. Please be careful to not damage the center Clamp 3.5∼4mm conductor. 5mm 3.5mm Soldering Contact ④ Solder up the contact with the center conductor. ④ Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. No gap Washer ⑤ Insert the washer and insulator as fig. 5. ⑤ Insulator ⑥ Insert the above assembly into the body and screw up by wrench. ⑥ ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 10 N Series Unit：mm ○ Assembly Instruction(4）MIL Clamp Straigh Cable Plug Parts Configulration Nut Gasket ※Washer Clamp Body Contact ※ As for N-P-8-1-CF, N-P-8-1-Ni-CF and UG-21D/U-CF, washer is not attached. The washer is not inserted into the cable. ① The cable length require for the single-ended ① cable assembly as following table. Part Number L1 L（mm） N-P-8-1-CF N-P-8-1-Ni-CF L1ー11.4 UG-21D/U-CF N-P-10-CF N-P-10-Ni-CF Outer Conductor Washer Sheath L1ー21.5 N-P-10DFB-1-CF ② ② Insert the nut, washer and gasket into the cable. Cut the sheath 10mm from the end of the cable and insert the clamp. Please be careful to not damage the outer 10mm ③ Nut conductor. Clamp Gasket ③ Pick the outer conductor and turn down to the clamp. Cut the outer conductor along the clamp. Cut the insulator and center conductor as fig.3. Tip the outer conductor and turn down to the clamp equally. Insulator Please be careful to not damage the center Center Conductor conductor. （Pre-soldering） Part Number B N-P-8-1-CF N-P-8-1-Ni-CF UG-21D/U-CF 5.0mm A A（mm） B（mm） 1.0 3.5 ∼ 4.0 1.8 4.0 ∼ 4.5 N-P-10-CF ④ N-P-10-Ni-CF N-P-10DFB-1-CF Soldering ④ Solder up the contact with the center conductor. Contact Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. No gap ⑤ ⑤ Insert the above assembly into the body and screw up by wrench. ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 11 N Series Unit：mm ○ Assembly Instruction(5）MIL Clamp Straight Cable Jack Parts Configulration Nut ※Washer Gasket Calmp Contact Body ※ As for N-J-8-1-CF, N-J-8-1-Ni-CF and UG-23D/U-CF, the washer is not attached. The washer is not inserted into the cable. ① The cable length require for the single-ended cable assembly as following table. ① Part Number N-J-8-1-CF L1 N-J-8-1-Ni-CF UG-23D/U-CF Sheath ② L（mm） L1ー13.2 L1ー13.8 N-J-10-CF Washer Outer conductor N-J-10-Ni-CF L1ー23.4 N-J-10DFB-1-CF ② Insert the nut, washer and gasket into the cable. Cut the sheath 10mm from the end of the cable and insert the clamp. 10mm Nut Clamp Gasket Please be careful to not damage the outer conductor. ③ Pick the outer conductor and turn down to the clamp equally/ Insulator ③ Pick the outer conductor and turn down to the clamp. Cut the outer conductor along the clamp. Outer Conductor Cut the insulator and center conductor as fig.3. （Pre-soldering） Please be careful to not damage the center conductor. 5mm Part Number A B ④ Soldering Contact No gap A（mm） B（mm） N-J-8-1-CF N-J-8-1-Ni-CF UG-23D/U-CF 1.0 3.5 ∼ 4.0 N-J-10-CF N-J-10-Ni-CF N-J-10DFB-1-CF 1.8 4.0 ∼ 4.5 ④ Solder up the contact with the center conductor. Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. ⑤ ⑤ Insert the above assembly into the body and screw up by wrench. ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 12 N Series Unit：mm ○ Assembly Instruction(6) Crimp Straight Cable Plug Parts Configulration Ferule Boot Sleeve Contact Insulator ① Body Coupling Ring Gasket ① The cable length require for the single-ended cable assembly. L L+17mm ② Insert the boot into the cable. Cut the cable as ② fig.2. Please be careful to not damage the outer Sheath Outer conductor Boot Cable conductor. 12.4mm ③ ③ After Inserting the ferule, tip the outer Ferule Insulator conductor and spread the top of the outer conductor. Insert the sleeve between outer conductor and the insulator. Sleeve ④ ④ Cut the insulator along the sleeve. And cut the outer conductor along the sleeve. Outer Conductor Sleeve ⑤ Put the contact into the center hole of the crimp tool and ⑤ insert the cable assembly and crimp the contact as fig.5. ● Crimp Tool : CR-H-1152 Center hole Tool Insulator Center conductor (3mm) Contact ⑥ Insert the above cable assembly into the body and crimp Tool as fig.6. Body end is leveled to the tool end. ● Crimp Tool : CR-H-1152 ⑥ Tool end Body Body end Tool ⑦ Screw clearance Reverse thread Boot Hollow ⑦ Screw up the cable assembly into the body until the Gasket reverse thread is end and reached hollow . Coupling ring After the coupling ring is screwed, fit the gasket into the screw clearance. Cover the boot on the root of the connector. Interface ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 13 N Series Unit：mm ○ Assembly Instruction(7) Crimp Straight Cable Plug Parts Configulration Ferule Boot Sleeve Contact Gasket Body Coupling Ring ① The cable length require for the single-ended cable ① assembly. L+22mm L ② Insert the boot into the cable. Cut the cable as ② 15mm fig.2. Please be careful to not damage the outer conductor. Outer Conductor Cable Boot Sheath ③ After Inserting the ferule, tip the outer Ferule ③ Insulator conductor and spread the top of the outer conductor. Insert the sleeve between outer conductor and the insulator. Plunge the sleeve by stripper without diging the edge. ● Stripper Part No. : 357J-15485 Sleeve Pull out the edge Push this side Stripper ④ Cut the insulator by stripper as fig.4. ④ Insert the stripper and dig the edge to the insulator. Rotate the stripper a few times and pull off the insulator. And cut the outer conductor along the sleeve. Cut off the round ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 14 N Series Unit：mm ○ Assembly Instruction(7) Crimp Straight Cable Plug ⑤ Put the contact into the center hole of the crimp tool and ⑤ insert the cable assembly and crimp the contact as fig.5. Center hole ● Crimp Tool : CR-H-13970 Tool Center Conductor 3.0mm 5.6mm Contact Tool ⑥ ⑥ Insert the above cable assembly into the body and crimp Tool end as fig.6. Body end is leveled to the tool end. Body Body end Tool Screw clearance ⑦ Coupling Ring Boot ⑦ Screw up the cable assembly into the body until the reverse thread is end and reached hollow . Gasket After the coupling ring is screwed, fit the gasket into Reverse thread the screw clearance. Cover the boot on the root of the connector. Interface Hollow ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 15