MCR006 Resistors Thick film rectangular MCR006 (0201 size : 1 / 20W) zFeatures 1) Extremely small light Area ratio is 60% smaller than that of chip 1005, while weight ratio has been cut 80%. 2) Highly reliable chip resistor Ruthenium oxide dielectric offers superior resistance to the elements. 3) Electrodes not corroded by soldering Thick film makes the electrodes very strong. 4) Flat surface further facilitates mounting 5) ROHM resistors have approved ISO–9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. zRatings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.05W (1 / 20W) at 70°C 100 POWER LOAD (%) 80 60 40 20 0 −55 0 70 100 125 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E= P×R Nominal resistance Operating temperature E: Rated voltage (V) P: Rated power (W) R: Nominal resistance (Ω) Limiting element voltage 25V See Table 1. −55°C to +125°C 1/5 MCR006 Resistors Table 1 Jumper type Resistance Max. 100mΩ Rated current Resistance tolerance 0.5A Operating temperature −55°C to +125°C Resistance range (Ω) Resistance temperature coefficient (ppm / °C) J (±5%) 10≤R≤10M (E24) ±250 F (±1%) 100≤R≤10M (E24) ±250 zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. zCharacteristics Item Guaranteed value Resistor type Jumper type Test conditions (JIS C 5201-1) J : ±5% F : ±1% Max. 100mΩ JIS C 5201-1 4.5 Variation of resistance with temperature See Table.1 Max. 100mΩ JIS C 5201-1 4.8 Measurement : +20 / −55 / +20 / +125°C Overload ± (2.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Limiting Element Voltage×2 : 50V Resistance Solderability Resistance to soldering heat Rapid change of temperature A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (1.0%+0.05Ω) Max. 100mΩ No remarkable abnormality on the appearance. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) Max. 100mΩ JIS C 5201-1 4.19 Test temp. : −55°C~+125°C 100cyc ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h~1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.1 Rated voltage (current), 70°C±3°C 1.5h : ON − 0.5h : OFF Test time : 1,000h~1,048h ± (3.0%+0.1Ω) Max. 100mΩ JIS C 5201-1 4.25.3 125°C Test time : 1,000h~1,048h ± (1.0%+0.05Ω) Max. 100mΩ JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. Max. 100mΩ ± (1.0%+0.05Ω) Without mechanical damage such as breaks. JIS C 5201-1 4.33 2/5 MCR006 Resistors zExternal dimensions (Unit : mm) 1 0.1±0.05 2 3 No. 0.15±0.05 4 0.23±0.03 0.6±0.03 Thick dielectric glaze of ruthenium (only silver used for jumper) 2 Thick film of palladium-silver for primary electrode 3 Nickel-coated secondary electrode 4 External electrode coated with Sn/Pb or Sn 5 Alumina substrate 6 Overcoating (resin) 0.3±0.03 5 Material 1 6 zPackaging Reel Taping P0 P2 φD0 E F A0 W 02 04 06 08 06 D 04 B 02 A 08 B0 P1 Heat crimp cover/Tape Thick paper Square press hole Cover tape Chip resistor T C Label Press career tape （Unit：mm） EIAJ ET-7200A compliant (Unit : mm) A φ180 B 0 −15 φ60 C +1 0 9 +1.0 0 W F E A0 B0 8.0±0.2 3.5±0.05 1.75±0.1 0.38±0.03 0.68±0.03 D0 P0 P1 P2 T +0.1 φ1.5 0 4.0±0.1 2.0±0.05 2.0±0.05 Max. 0.50 D φ13±0.2 3/5 MCR006 Resistors zPart designation 3-digit or 4-digit IEC coding system Part No. Nominal resistance M C R 0 6 0 Y Z Packaging specifications code Part No. Code MCR006 YZP J P Resistance tolerance Packaging style Standard ordering unit (pcs) Paper tape 15,000 F ±1% J ±5% Specify "J" for jumper also. zDimensions 0.38 0.68 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER 0.66 0.60 0.58 0.27 THICKNESS (mm) WIDTH (mm) 0.62 0.32 0.30 0.28 0.25 0.23 0.21 0.56 0.26 0.19 0.54 0.24 0.17 0.52 10 100 1k 10k 100k 1M 0.22 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER 0.29 0.34 0.64 LENGTH (mm) 0.31 JIS C 5201-1 4.4.2 SAMPLE SIZE : n=20pcs MICROMETER 0.36 10 100 1k 10k 100k 0.15 1M 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.2 Dimensions (length) Fig.3 Dimensions (width) Fig.4 Dimensions (thickness) JIS C 5201-1 4.5 SAMPLE SIZE : n=20pcs 20°C 65%RH DC RESISTANCE (%) 6.0 4.0 2.0 0 – 2.0 – 4.0 – 6.0 – 8.0 10 100 1k 10k 100k 1M 800 4.0 JIS C 5201-1 4.8 SAMPLE SIZE : n=10pcs 20°C / −55°C 20°C / 125°C 600 400 2.0 200 1.0 0 −200 0.0 −1.0 −400 −2.0 −600 −3.0 −800 10 100 1k 10k 100k 1M JIS C 5201-1 4.13 SAMPLE SIZE : n=10pcs RATED VOLTAGE × 2.5TIMES : 2s LIMITING ELEMENT VOLTAGE : 50V 3.0 ∆R/R (%) 8.0 TEMPERATURE COEFFICIENT (ppm/°C) zElectrical characteristics −4.0 10 100 1k 10k 100k RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.5 Resistance Fig.6 Variation of resistance with temperature Fig.7 Overload 1M 4/5 MCR006 Resistors JIS C 5201-1 4.18 SAMPLE SIZE : n=10pcs SOLDERING CONDITION : 260°C 10s 1.0 1.5 ∆R/R (%) 0.5 0.0 −0.5 JIS C 5201-1 4.19 SAMPLE SIZE : n=10pcs −55°C / 125°C 100cyc 1.0 2.0 0.5 1.0 0 −0.5 −1.0 −1.0 −2.0 −1.5 −1.5 −3.0 −2.0 −2.0 100 1k 10k 100k 1M 10 100 Fig.8 Resistance to soldering heat 1k 10k 100k −4.0 1M JIS C 5201-1 4.24 SAMPLE SIZE : n=10pcs 40°C 93%RH WITH NO LOAD 1000h 2.0 0 −1.0 1.0 1.0 0.5 0.5 0 −0.5 0 −0.5 −1.0 −3.0 −1.5 −1.5 −4.0 −2.0 1k 10k 100k 1M 1M 10 100 1k 10k 100k 1M JIS C 5201-1 4.29 SAMPLE SIZE : n=10pcs IPA, 5min. 1.5 −1.0 100 100k 2.0 JIS C 5201-1 4.19 SAMPLE SIZE : n=10pcs −55°C / 125°C 100cyc −2.0 10 10k Fig.10 Damp heat, steady state 1.5 ∆R/R (%) 1.0 1k Fig.9 Rapid change of temperature ∆R/R (%) 3.0 100 RESISTANCE (Ω) 2.0 4.0 10 RESISTANCE (Ω) RESISTANCE (Ω) ∆R/R (%) 0 −1.0 10 JIS C 5201-1 4.24 SAMPLE SIZE : n=10pcs 40°C 93%RH WITH NO LOAD 1000h 3.0 ∆R/R (%) 1.5 ∆R/R (%) 4.0 2.0 2.0 −2.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.11 Endurance at 70°C Fig.12 Endurance Fig.13 Resistance to solvents 2.0 JIS C 5201-1 4.33 SAMPLE SIZE : n=10pcs ENDURANCE WITH 90mm WIDTH 1.5 ∆R/R (%) 1.0 0.5 0.0 −0.5 −1.0 −1.5 −2.0 10 100 1k 10k 100k 1M RESISTANCE (Ω) Fig.14 Bend strength of the end face plating 5/5