Current Transducer HASS 50..600-S For the electronic measurement of currents: DC, AC, pulsed, mixed, with galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). IPN = 50 .. 600 A All Data are given with a RL = 10 kΩ Electrical data Primary nominal current rms IPN (A) 50 100 200 300 400 500 600 VOUT GTH VREF RL ROUT CL V C IC Primary current Type measuring range IPM (A) ± 150 ± 300 ± 600 ± 900 ± 900 ± 900 ± 900 HASS 50-S HASS 100-S HASS 200-S HASS 300-S HASS 400-S HASS 500-S HASS 600-S Analog Output voltage @ IP Theoretical sensitivity Reference voltage 1) Ouput voltage Ouput impedance Load impedance Load resistance Output internal resistance Capacitive loading (± 20 %) Supply voltage (± 5 %)2) Current consumption @ VC = 5V Features VOE ± (0.625. IP/ IPN) V 0.625 V/ IPN 2.5 ± 0.025 V typ. 200 Ω ≥ 200 Ω ≥ 2 kΩ < 5 Ω = 4.7 nF 5 V 19 mA Accuracy - Dynamic performance data Accuracy 3) @ IPN , TA = 25°C εL Linearity error 0 .. IPN 0 .. IPM TCVOE Temperature coefficient of VOE (+25.. +85°C) (-40.. +25°C) TCVREF Temperature coefficient of VREF (+25.. +85°C) (-40.. +25°C) TCVOE/VREFTemperature coefficient of VOE /VREF TCG Temperature coefficient of G VOE Electrical offset voltage @ IP = 0, TA = 25°C VOM Magnetic offset voltage @ IP = 0 after an overload of IPM tra Reaction time to 10 % of IPN step tr Response time to 90 % of IPN step di/dt di/dt accurately followed Vno Output voltage noise (DC .. 10 kHz) (DC .. 1 MHz) BW Frequency bandwidth (- 3 dB) 4) X Notes: ≤ ± 1 % ≤ ± 0.5 % ≤ ± 1 % ≤ ± 0.4 mV/K ≤ ± 0.525 mV/K ≤ ± 0.01 %/K ≤ ± 0.015 %/K ≤ ± 0.15 mV/K ≤ ±0.05% of reading//K VREF ± 0.025 V < ± 0.4 < 3 < 5 > 100 < 20 < 40 DC .. 50 % µs µs A/µs mVpp mVpp kHz ●● Hall effect measuring principle ●● Galvanic isolation between primary and secondary circuit ●● Isolation test voltage 3300 V ●● Low power consumption ●● Single power supply + 5 V ●● Fixed offset & Gain ●● Isolated plastic case recognized according to UL 94-V0. Advantages ●● Easy installation ●● Small size and space saving ●● Only one design for wide current ratings range ●● High immunity to external interference ●● Internal & external reference. Applications ●● AC variable speed drives ●● Static converters for DC motor drives ●● Battery supplied applications ●● Uninterruptible Power Supplies (UPS) ●● Switched Mode Power Supplies (SMPS) ●● Power supplies for welding applications. Application domain ●● Industrial. It is possible to overdrive VREF with an external reference voltage between 1.5V - 2.8V providing its ability to sink or source approximately 5 mA. 2) Maximum supply voltage (not operating) < 6.5 V 3) Excluding Offset and Magnetic offset voltage 4) Small signal only to avoid excessive heatings of the magnetic core. 1) Page 1/3 120323/14 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com Current Transducer HASS 50..600-S General data TA TS m Ambient operating temperature Ambient storage temperature Mass Standards - 40 .. + 85 - 40 .. + 85 55 EN 50178:1997 °C °C g Isolation characteristics Vb Rated isolation voltage rms with following conditions -Over voltage category Ⅲ -Pollution degree 2 -Heterogeneous field Single insulation Reinforced insulation Vd Ve Vw dCp dCl CTI EN50178 600V 300V Rms voltage for AC isolation test, 50 Hz, 1 min Partial discharge extinction voltage rms @ 10 pC Impulse withstand voltage 1.2/50 µs Creepage distance Clearance distance Comparative Tracking Index (Group I) IEC61010-1 600V 150V 3.3 > 1 6 > 5.5 > 5.5 > 600 kV kV kV mm mm V Safety This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer’s operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a build-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/3 120323/14 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com Dimensions HASS 50..600-S (in mm) Mechanical characteristics ●● ●● ●● ●● ●● General tolerance ± 0.5 mm Aperture for primary conductor 20.4x10.4x0.5mm Transducer fastening M4 Recommended fastening torque <1.5N・m Connection of secondary Molex 5045-04A Remarks ●● Arrow indicates positive current flow direction. ●● Temperature of the primary conductor should not exceed 100°C. Page 3/3 120323/14 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com