S/CON/SOM040200/B/18/12/14 Page 1/5 UK MOSFET BASED DC SOLID-STATE RELAY SOM040200 Latest MOSFET technology generation. Ultra low on-state resistance. Low output leakage current. Low control current consumption. Built-in overvoltage protection Reverse protected triggered control input to avoid linear control risks Max. permanent output voltage Max. load current with heatsink Touch protected housing IP20 Load voltage range 5-110VDC Fig. 1 Load current range Up to 40A (with heatsink) 3.5-32VDC Control voltage range No radiated or conducted disturbances 110VDC 40ADC Control input voltage range In & case / Out Insulation Connections Dimensions (WxHxD) Weight 3.5-32VDC 2.5kV Screw terminals 45 x 58.5 x 30 80g HIGH SIDE WIRING DIAGRAM (Load connected to “-“) LOW SIDE WIRING DIAGRAM (Load connected to “+”) Fig. 2 See Instruction sheet for selective the right protective components See Instruction sheet to select the right protective components The red paths (C1/D2) must be as short as possible ! Fig. 3 Proud to serve you Data given at Tambient=25°C and subject to modification without previous notice The red paths (C1/D2) must be as short as possible ! INTERNAL DIAGRAM ® celduc r e l a i s celduc® r e l a i S/CON/SOM040200/C/18/12/14 s Page 2/5 UK INPUT CIRCUIT CONTROL INPUT CHARACTERISTICS CHARACTERISTIC Nom. Control voltage Min. Control current Control voltage range Control current consumption Releasing control voltage Max. reverse control voltage Input impedance LABEL VALUE INFO. Ucnom Icmin Uc Ic Ucoffmax -Ucmax Rin 12-24VDC 35mADC 3.5 – 32VDC 32 – 35mADC (for control voltage range) 1VDC 32VDC Current limitation -100µA/°C typical ON=3.3V See fig. 5 typical OFF= 2.6V -Icmax<100µA See fig. 5 POWER OUTPUT CHARACTERISTICS CHARACTERISTIC Nominal voltage VALUE Uenom Voltage range POWER CIRCUIT LABEL Ut INFO. 90VDC Ue 5-110VDC Non-repetitive peak voltage Utp 200V Overvoltage protection D1 Varistor 75V size 20 Max reverse voltage drop (internal diode at OFF state) -Ut 1.5V @Ie=-56A @Uc=0 Resistive Motor 40A Please contact us See fig. 7 (limits) Maximum nominal currents Ie max Non-repetitive peak overload current Id max 380A Min. load current Iemin 5mA Ielk max 3mA @Utmax @Tjmax Max. on-state resistance RDSon 46m @Iemax @Tjmax Typ. output capacitance Cout 1.1nF Junction/case thermal resistance per power element Rthjc 0.7K/W Built-in heatsink thermal resistance vertically mounted Rthra 10K/W @Tra=75°C Heatsink thermal time constant Tthra 10 minutes @Tra=40°C Uimp 2.5kV Uimp Uimp Rio Cio Tjmax Tstg Tamb Tc 2.5kV 2.5kV 1G <8pF 175°C -40->+100°C -25->+90°C 100°C Max. leakage current Control inputs/power outputs insulation voltage Inputs/case insulation voltage Outputs/case insulation voltage Isolation resistance Isolation capacitance Maximum junction temperature Storage ambient temperature Operating ambient temperature Max. case temperature See fig. 8 See fig. 7 PROTECTION CHARACTERISTICS Leakage current (Ielk) vs DC voltage (Ut) Absolute limits Uto Utp Ielk / Ie PROTECTION 1 0,8 t max 0,6 0,4 0,2 0 0 20 40 60 80 100 120 140 160 180 200 Ut (V) U t max ( =U emax) Ielk : Leakage current of the relay Ie : User load nominal current Utp : Relay max. non repetitive peak voltage 0. 75 ( Uto Ut max) Ie P ( protection ) 1W max ( Uto Ut max) Ie t 1 T Utp Utmax : Max. nominal voltage of the relay t : Overvoltage duration Uto : Possible overvoltage above Utmax T: Time between 2 overvoltage Utn = Ue : User DC power supply voltage celduc® r e l a i S/CON/SOM040200/C/18/12/14 s Page 3/5 UK TIME CHARACTERISTICS TIME CHARACT. Fig. 4 TIME DIAGRAMS CHARACTERISTIC LABEL VALUE Turn on time ton 20µs Turn on delay tdon 20µs Turn off time toff 20µs Turn off delay tdoff 20µs F(on-off) >1000Hz (for high frequency, take 2 x Ie to calculate the heatsink; the protections must be chosen carefully) Max. On-Off frequency INFO. Refer to the instruction sheet MISC. CONNECTIONS GENERAL INFORMATION Connections Power Screwdriver advised Control POZIDRIV2 Min and max tightening torque 2 N.m 1.2 N.m Insulated crimp terminals (round tabs, eyelet type) M5 M4 Display Green LED (indicates relay has switched ON) Housing UL94V0 Mounting 2 screws (M4x12mm ; tightening = 1.2N.m) Noise level None Weight See mounting sheet 80g E.M.C. IMMUNITY GENERAL STANDARDS Standards IEC60947-1 Protection level IP20 Protection against direct touch Yes CE marking Yes UL, cULUS Yes TYPE OF TEST STANDARD LEVEL Fast transients bursts EN61000-4-4 4kV criterion B Electric chocks EN61000-4-5 1kV criterion B Voltage drop EN61000-4-11 - EFFECT celduc® r e l a i S/CON/SOM040200/C/18/12/14 s Page 4/5 UK CHARACTERISTIC CURVES Fig. 5 INPUT CHARACTERISTIC Ic (mADC) 50 Fig. 6 RDSon 60 (mOhms) -35°C -35°C 45 ON RESISTANCE VS JUNCTION TEMPERATURE 50 40 25°C 35 40 30 100°C 25 30 20 20 15 10 10 5 0 0 0 2 4 6 8 -50 10 12 14 16 18 20 22 24 26 28 30 32 0 50 Fig. 7 100 150 Junction Temperature (°C) Uc (VDC) POWER DISSIPATED AND LOAD CURRENT LIMIT VS TEMPERATURE Permanent current Ie (ARMS) Power dissipated (W) Please refer to the installation notice for precautions about mounting the device on a heatsink. 97,8 45 1.2K/W 1.1K/W 0.9K/W 0.75K/W 0.55K/W 0.3K/W 40 77,3 35 59.2 30 43.5 25 30.2 20 19.3 15 10.9 10 4.8 5 1.2 8K/W 4K/W 2.2K/W 2.1K/W 0 0 10 20 30 40 50 60 70 80 90 100 0 110 Ambient temperature (°C) 10K/W = No Heatsink 2.1K/W = WF210000 0.75K/W = WF070000 Fig. 8 4K/W = 150x150x3mm aluminium sheet 1.2K/W = WF121000 0.55K/W = WF050000 2.2K/W = WF262100 1.1K/W = WF131100 0.3K/W = WF031100 2.2K/W = WF151200 0.9K/W = WF115100 PEAK OVERLOAD CURRENT vs. PULSE DURATION CHARACTERISTIC Ie 320 (Apk) 280 Non-repetitive D=1% (Tc=100°C, Tjmax=175°C) Repetitive D=5% (Tc=100°C, Tjmax=175°C) 240 Repetitive D=10% (Tc=100°C, Tjmax=175°C) 200 160 Repetitive D=20% (Tc=100°C, Tjmax=175°C) 120 t1 D% 100 t2 80 40 Repetitive D=50% (Tc=100°C, Tjmax=125°C) 0 0,1 1 10 100 1000 Pulse duration (ms) celduc® r e l a i S/CON/SOM040200/C/18/12/14 s Page 5/5 UK DIMENSIONS AND ACCESSORIES Fig. 9 DIMENSIONS (mm) 2 Fig. 10 - 1 + ACCESSORIES FASTON : Please contact us ® celduc r e l a i www.celduc.com s 5 Rue Ampère B.P. 30004 42290 SORBIERS - FRANCE E-Mail : [email protected] Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19