Datasheet

TVS Diode Arrays (SPA®® Diodes)
Lightning Surge Protection - SP1050 Series
SP1050 Series for Power-over-Ethernet PSE Protection
RoHS Pb GREEN
Description
The SP1050-04BTG provides over-voltage protection for
Power-over-Ethernet PSE equipment in a space saving
SOIC-8 package. It incorporates 4 TVS Diodes each with
their own decoupling capacitor to stabilize power supplies.
The SP1050 is compatible with IEEE 802.3af and IEEE
802.3at requirements while allowing PoE based systems
to be protected against damaging threats such as lightninginduced surges (IEC61000-4-5), electrical fast transients
(IEC61000-4-4), and Electrostatic Discharges (IEC61000-42).
The low clamping voltage of 96V makes it compatible with
PSE controller technologies.
Functional Block Diagram
GND
2-3-6-7
PS1
1
PS2
4
Features
PS3
5
• P
eak pulse power: up to
2.7 kW (8/20 μs)
PS4
8
• L
ightning protection,
IEC61000-4-5, 24A
(tp=8/20µs)
• ESD protection of ±30kV
contact discharge,
±30kV air discharge,
(IEC61000-4-2)
• Stand-off voltage of 58 V
• L
ow clamping voltage of
96V (MAX) at 24A
Absolute Maximum Ratings
Parameter
Rating
Units
Peak Pulse Current (8/20µs)
24
A
Peak Pulse Power (8/20µs)
2700
W
IEC 61000-4-2, Contact Discharge, (Level 4)
30
kV
IEC 61000-4-2, Air Discharge, (Level 4)
30
kV
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress only rating and operation of the device
at these or any other conditions above those indicated in the operational sections of this
specification is not implied.
Life Support Note:
Not Intended for Use in Life Support or Life Saving Applications
The products shown herein are not designed for use in life sustaining or life saving
applications unless otherwise expressly indicated.
©2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 01/15/16
Applications
• Power-over-Ethernet
• L
ow leakage current of
0.1 μA at 25 °C and 1 μA
at 85 °C
• Operating Tj max: 150 °C
• JEDEC registered package
outline
• Embeds 4 decoupling
capacititors
• Meets most stringent
environment
TVS Diode Arrays (SPA®® Diodes)
Lightning Surge Protection - SP1050 Series
Electrical Characteristics (TOP = 25°C)
Parameter
Symbol
Leakage Current
IRM
Breakdown Voltage
Clamping Voltage
2
Dynamic Resistance
Typ
Max
Units
-
-
0.1
µA
-
-
1
µA
64
67
-
V
-
-
96
V
-
0.35
-
Ω
-
35
-
pF
1
VBR
IR= 1mA
VC
IPP= 24A, tp=8/20 μs
TLP, tP=100ns, I/O to GND
C
Capacitance 1
Min
85°C, VPoE= 58V
RDYN
2
Test Conditions
25°C, VPoE= 58V
2
VPoE= 58V
Note: 1 Parameter is guaranteed by design and/or device characterization.
2. Transmission Line Pulse (TLP) with 100ns width and 200ps rise time.
8/20µs 8/20μS Pulse Waveform
Capacitance vs. Reverse Bias
100.0
110%
90.0
90%
80.0
80%
70.0
Capacitance (pF)
Percent of IPP
100%
70%
60%
50%
40%
30%
60.0
50.0
40.0
30.0
20.0
20%
10.0
10%
0%
0.0
0.0
5.0
10.0
15.0
20.0
25.0
44
30.0
Time (μs)
46
48
50
52
54
56
58
Bias Voltage (V)
Clamping Voltage vs IPP
Non-Repetitive Peak Pulse Power vs. Pulse Time
100
100.0
80.0
Peak Pulse Power (kW)
Clamp Voltage (V C )
90.0
70.0
60.0
50.0
40.0
30.0
10
1
20.0
10.0
0.0
0.0
4.0
8.0
12.0
16.0
Peak Pulse Current -I PP (A)
©2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 01/15/16
20.0
24.0
0.1
1
10
100
Peak Pulse Duraon - tP (µs)
1000
TVS Diode Arrays (SPA®® Diodes)
Lightning Surge Protection - SP1050 Series
Transmission Line Pulse (TLP)
20
18
TLP Current (A)
16
14
12
10
8
6
4
2
0
0
10
20
30
40
50
60
70
80
TLP Voltage (V)
Soldering Parameters
Pre Heat
Pb – Free assembly
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus) Temp (TL)
to peak
3°C/second max
TS(max) to TL - Ramp-up Rate
3°C/second max
Reflow
- Temperature (TL) (Liquidus)
217°C
- Temperature (tL)
60 – 150 seconds
Peak Temperature (TP)
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
260°C
©2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 01/15/16
tP
TP
Temperature
Reflow Condition
Critical Zone
TL to TP
Ramp-up
TL
TS(max)
tL
Ramp-do
Ramp-down
Preheat
TS(min)
25
tS
time to peak temperature
Time
TVS Diode Arrays (SPA®® Diodes)
Lightning Surge Protection - SP1050 Series
Application Schematic
Figure 1: Typical application circuit with fully integrated PSE controller
+
Tx
48V
Rx
RJ-45
-
Tx
V1
o
C om
RJ-45
Rx
Gnd
PS1
PoE
Controller
PS2
PS3
Tx
PS4
Rx
RJ-45
SP1050-04BTG
Tx
RJ-45
Rx
Figure 1 shows typical application of power sourcing equipment (PSE) allowing communication and power sourcing for several powered devices (PD). The
SP1050-04BTG is optimized for space savings as there is generally a multiple of 4 present. This protection device complies with IEEE 802.3af and the IEC
61000-4-5 (Level 4) standard.
©2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 01/15/16
TVS Diode Arrays (SPA®® Diodes)
Lightning Surge Protection - SP1050 Series
Package Dimensions of SOIC-8
Package
SOIC
Pins
8
JEDEC
MS-012
LF
Millimetres
o
Recommended
Soldering Pad Outline
(Reference Only)
Inches
Min
Max
Min
Max
A
1.35
1.75
0.053
0.069
A1
0.10
0.25
0.004
0.010
A2
1.25
1.65
0.050
0.065
B
0.31
0.51
0.012
0.020
c
0.17
0.25
0.007
0.010
D
4.80
5.00
0.189
0.197
E
5.80
6.20
0.228
0.244
E1
3.80
4.00
0.150
0.157
1.27 BSC
e
1.27
0.40
L
0.050 BSC
0.050
0.016
Embossed Carrier Tape & Reel Specification — SOIC Package
Millimetres
User Feeding Direction
E
Pin 1 Location
Max
Min
Max
1.65
1.85
0.065
0.073
F
5.4
5.6
0.213
0.22
P2
1.95
2.05
0.077
0.081
D
1.5
1.6
0.059
0.063
1.50 Min
D1
P0
10P0
SP 1050 - 04 B T G
©2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 01/15/16
4.1
0.154
0.161
1.574 +/- 0.008
11.9
12.1
0.468
0.476
P
7.9
8.1
0.311
0.319
A0
6.3
6.5
0.248
0.256
B0
5.1
5.3
0.2
0.209
K0
2
2.2
0.079
0.087
0.30 +/- 0.05
0.012 +/- 0.002
Ordering Information
Part Numbering System
Number of
Channels
3.9
40.0 +/- 0.20
0.059 Min
W
t
TVS Diode Arrays
(SPA® Diodes)
Series
Inches
Min
G= Green
T= Tape & Reel
Package
B = SOIC
Part Number
Package
Marking
Min. Order Qty.
SP1050-04BTG
SOIC Tape & Reel
SP1050
2500