DATA SHEET SMP1307 Series: Very Low Distortion Attenuator Plastic Packaged PIN Diodes Applications Very low distortion PI and TEE attenuators Cable TV AGC High-volume wireless systems Features Low distortion design Frequency range from 5 MHz to > 2 GHz Packages rated MSL1 @ 260 C per JEDEC J-STD-020 Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Description The SMP1307 series of plastic packaged, surface mountable, low capacitance (0.3 pF) silicon PIN diodes is designed for attenuator applications from 5 MHz to beyond 2 GHz. The thick 175 μm I region width of these PIN diodes makes them very attractive for use in very low distortion PI and TEE attenuators commonly found in TV distribution applications. The 1.5 μs carrier lifetime of these diodes results in resistance of 100 Ω maximum at 1 mA and 10 Ω maximum at 10 mA. The SMP1307 series is available in a selection of plastic packages, as a single diode in the small footprint SOD-323 package, and in a variety of configurations in the SOT-23 package. Also available in an SOT-5 package (SMP1307-027) is a four-diode array designed for insertion in commonly used fourdiode PI attenuator circuits. Table 1 describes the various packages and marking of the SMP1307 series. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200045M • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 26, 2016 1 DATA SHEET • SMP1307 SERIES Table 1. SMP1307 Series Packaging and Marking Common Anode Common Cathode Series Pair Reverse Series Pair Single PI SOT-23 SOT-23 SOT-23 SOT-23 SOD-323 Green™ SOT-5 SMP1307-003LF Green™ Marking:RJ9 SMP1307-004LF Marking: RJ3 SMP1307-005LF Green™ Marking: RJ2 SMP1307-006LF Green™ Marking: RJ8 SMP1307-011LF Marking: RJ SMP1307-027LF Green™ Marking: RJM LS = 1.5 nH LS = 1.5 nH LS = 1.5 nH LS = 1.5 nH LS = 1.5 nH The Pb-free symbol or “LF” in the part number denotes a lead-free, RoHS-compliant package unless otherwise noted as Green™. Tin/lead (Sn/Pb) packaging is not recommended for new designs. 3 2 1 4 5 VTUNE (0 - 20 V) C6 10000 pF R2 1 kΩ C1 10000 pF D1 C5 10000 pF D3 RF Input RF Output R1 560 Ω D2 R3 1 kΩ C2 10000 pF R5 560 Ω R4 1 kΩ D4 R6 560 Ω C4 10000 pF VREF (5 V) C3 10000 pF 200045-001 Figure 1. SMP1307-027 Block Diagram and Schematic SMP1307-027 Four-Diode PI Attenuator Electrical and Mechanical Specifications The SMP1307-027 uses four PIN diode junctions in a five-lead SOT package. It is configured for ease of insertion in the PI attenuator circuit commonly used for broadband TV distribution systems, covering a frequency range from 5 MHz to over 1 GHz. The absolute maximum ratings of the SMP1307 series are provided in Table 2. Electrical specifications are provided in Table 3. Resistance versus temperature measurements are provided in Table 4. A broadband attenuator was designed using the SMP1307-027 that shows good performance up to 2 GHz. The attenuator was evaluated with a 50 Ω source and load impedance. Figure 1 shows a block diagram and circuit diagram for this device (the typical performance of the SMP1307-027 is shown in Figure 2). Typical performance characteristics of the SMP1307 series are illustrated in Figures 2 to 6. Package dimensions are shown in Figures 7 to 11 (odd numbers), and tape and reel dimensions are provided in Figures 8 to 12 (even numbers). Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 April 26, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200045M DATA SHEET • SMP1307 SERIES Package and Handling Information Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. The SMP1307 series is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. Table 2. SMP1307 Series Absolute Maximum Ratings1 Parameter Symbol Reverse voltage Minimum Maximum Units 200 V VR Power dissipation @ 25 °C lead temperature PD 250 mW Storage temperature TSTG –65 +150 C Operating temperature TA –65 +150 C 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industrystandard ESD handling precautions should be used at all times. Table 3. SMP1307 Series Electrical Specifications1 (TA = +25 C, Unless Otherwise Noted) Parameter Reverse current Symbol IR Test Condition Max Units VR = 200 V 10 μA 0.3 pF 100 15 3 Ω Ω Ω Capacitance2 CT f = 1 MHz, V = 30 V Resistance RS f = 100 MHz Min Typical I = 1 mA I = 10 mA I = 100 mA 75 Forward voltage VF IF = 10 mA 0.85 V Carrier lifetime TI IF = 10 mA 1.5 μs 175 μm I region width 1 Performance is guaranteed only under the conditions listed in this table. 2 The SMP1307-027 maximum capacitance is 0.45 pF. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200045M • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 26, 2016 3 DATA SHEET • SMP1307 SERIES Table 4. Resistance vs Temperature @ 100 MHz IF (mA) RS @ –55 °C (Ω) RS @ –15 °C (Ω) RS @ +25 °C (Ω) RS @ +65 °C (Ω) RS @ +100 °C (Ω) 0.02 2386 2360 2546 2520 2440 0.10 560 598 632 633 639 0.3 203 219 236 239 242 1.0 66.1 71.2 79.3 83.6 85.4 10 9.1 10.0 10.9 12.2 12.9 20 5.6 6.0 6.6 7.4 7.8 100 2.2 2.4 2.6 3.0 3.2 Typical Performance Characteristics 0 10000 VCTL = 20 V VCTL = 15 V 1000 VCTL = 0 V –30 –40 –50 0 0.5 1.0 1.5 100 10 200045-003 VCTL = 5 V –20 200045-002 Attenuation (dB) VCTL = 10 V Series Resistance (Ω) –10 1 0.1 0.01 2.0 0.1 1 10 100 Forward Current (mA) Frequency (GHz) Figure 3. Series Resistance vs Current @ 100 MHz Figure 2. SMP1307-027 Attenuation vs Frequency 0.8 100 1 0.1 0.01 400 500 600 700 800 Forward Voltage (mV) Figure 4. DC Characteristic 900 1000 0.6 0.5 1 MHz 0.4 0.3 100 MHz 0.2 1 GHz 200045-005 Capacitance (pF) 10 200045-004 Forward Current (mA) 0.7 0.1 0 0 1 2 5 10 20 Reverse Voltage (V) Figure 5. Capacitance vs Reverse Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 50 April 26, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200045M 100 DATA SHEET • SMP1307 SERIES 400 350 250 200 150 0V 10 V 100 40 V 50 0 0 500 1000 1500 200045-006 Conductance (μs) 300 2000 Frequency (MHz) Figure 6. Conductance vs Frequency and Reverse Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200045M • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 26, 2016 5 DATA SHEET • SMP1307 SERIES 0.060 (1.52 mm) Min. 0.070 (1.78 mm) Max. 0.090 (2.29 mm) Min. 0.107 (2.72 mm) Max. 0.044 (1.12 mm) Min. 0.054 (1.37 mm) Max. 1 0.000 (0 mm) Min. 0.004 (0.10 mm) Max. 0.013 (0.33 mm) Min. 0.017 (0.43 mm) Max. 2 0.012 (0.305 mm) Min. 0.016 (0.406 mm) Max. Cathode Indicator 0.036 (0.91 mm) Min. 0.046 (1.17 mm) Max. 0.008 Ref. 0.025 (0.635 mm) Min. 0.037 (0.940 mm) Max. Gauge Datum For Foot Length Measurement 0.005 (0.127 mm) Min. 0.008 (0.203 mm) Max. 0.010 (0.25 mm) Min. 0.018 (0.46 mm) Max. Dimensions are in inches (millimeters shown in parentheses) 200045-007 Figure 7. SOD-323 Package Dimension Drawing 2.00 ± 0.05 Cathode Indicator A A 1.75 ± 0.10 3.50 ± 0.05 ∅1.50 +0.1/–0 8.00 +0.30/–0.10 4.00 ± 0.10 B B 4.00 ± 0.10 ∅1.05 ± 0.05 0.84 1.25 ± 0.05 1.95 ± 0.05 1.02 2.90 ± 0.05 0.254 ± 0.02 8° Max 5° Max 1.46 ± 0.10 A Notes: 1. Carrier tape: black conductive polycarbonate or polystyrene. 2. Cover tape: transparent conductive material. 3. Cover tape size: 5.5 mm width. 4. ESD surface resistivity is ≥1 x 105 ~ ≤ 1 x 1011 Ohms/square. 5. 10 sprocket hole pitch cumulative tolerance: ±0.20 mm. 6. Ao and Bo measured on plane 0.30 mm above bottom of the pocket. 7. All measurements are in millimeters. 8. Standard reel size is 7 inches. Standard reel quantity is 3000 pcs. B 200045-008 Figure 8. SOD-323 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 April 26, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200045M DATA SHEET • SMP1307 SERIES 0.074 (1.90 mm) Ref. 5 1 4 2 0.020 (0.51 mm) 0.014 (0.35 mm) 0.012 (0.30 mm) 0.000 (0.00 mm) Min. 0.069 (1.75 mm) 0.052 (1.30 mm) 0.118 (3.00 mm) 0.087 (2.20 mm) 3 0.037 (0.95 mm) Ref. 0.064 (1.63 mm) 0.035 (0.90 mm) 0.012 (0.30 mm) Typ. 0.024 (0.61 mm) 0.004 (0.10 mm) 0.0104 (0.26 mm) 0.0035 (0.09 mm) Min. 0.122 (3.10 mm) 0.106 (2.70 mm) Dimensions are in inches (millimeters shown in parentheses) 200045-009 Figure 9. SOT-5 Package Dimension Drawing ∅1.50+ 0.10/–0.00 4.00 ± 0.10 4.00 (see Note 4) 2.00 ± 0.05 1.75 ± 0.10 Pin 1 A 8.00 +0.30/–0.10 3.20 ± 0.10 (Bo) A 3.50 ± 0.05 B 1.40 ± 0.10 (Ko) B B ∅1.00 Min R0.30 Typ 0.20 ± 0.03 Notes: 1. 2. 3. 4. 5. 6. Carrier tape: black conductive polystyrene. Cover tape material: transparent conductive HSA. Cover tape size: 5.40 mm width. Ten sprocket hole pitch cumulative tolerance = ±0.20 mm. All measurements are in millimeters. Standard reel size is 7 inches. Standard reel quantity is 3000 pcs. 3.15 ± 0.10 (Ao) A 200045-010 Figure 10. SOT-5 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200045M • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 26, 2016 7 DATA SHEET • SMP1307 SERIES 0.110 (2.80 mm) Min. 0.120 (3.04 mm) Max. 0.012 (0.30 mm) Min. 0.020 (0.50 mm) Max. 3 0.083 (2.10 mm) Min. 0.104 (2.64 mm) Max. 0.047 (1.20 mm) Min. 0.055 (1.40 mm) Max. 2 1 0.037 (0.95 mm) Ref. 0.020 (0.51 mm) Ref. 0.076 (1.92 mm) Ref. 0.035 (0.89 mm) Min. 0.044 (1.12 mm) Max. 0.003 (0.080 mm) Min. 0.008 (0.20 mm) Max. 8° Max. 0.0005 (0.01 mm) Min. 0.004 (0.10 mm) Max. 0.022 (0.55 mm) Ref. Dimensions are in inches (millimeters shown in parentheses) 200045-011 Figure 11. SOT-23 Package Dimension Drawing 4.00 ø1.00 Min ø1.5 + 0.1/–0 4.00 (See Note 5) 1.75 ± 0.10 3.50 ± 0.05 A 2.70 (Bo) R 0.3 Max 2.2 1.20 (Ko) 1.0 0.8 ± 0.05 R 0.5 Typ Pin 1 Indicator 8.00 + 0.3/–0.1 2.00 ± 0.05 0.25 ± 0.05 A 3.10 (Ao) A Notes: 1. 2. 3. 4. 5. 6. 7. Carrier tape: black conductive polycarbonate. Cover tape material: transparent conductive PSA. Cover tape size: 5.40 mm width. Tolerance ±0.10 mm. Ten sprocket hole pitch cumulative tolerance: ±0.2 mm. All measurements are in millimeters. Alternative carrier tape dimensions are: Ao = 3.3 Bo = 2.9 Ko = 1.22 200045-012 Figure 12. SOT-23 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 April 26, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200045M DATA SHEET • SMP1307 SERIES Copyright © 2002-2007, 2009-2010, 2013-2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200045M • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • April 26, 2016 9