DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Applications Product Description The SE5510T is a complete 802.11n WLAN RF frontend module providing all the functionality of the power amplifiers, LNA, power detector, Antenna switches, filtering and associated matching. The SE5510T provides a complete 2.4 GHz and 5 GHz WLAN RF solution from the output of the transceiver to the antennas in a compact form factor. IEEE802.11b DSSS WLAN IEEE802.11a,g,n OFDM WLAN Embedded applications with Bluetooth (Mobile) Features All RF ports matched to 50 Ω Integrated 2.4,5 GHz PA, 5 GHz LNA, SP3T, SP2T switches and filtering Integrated Power Detector 19.5 dBm @ 3 % EVM, 802.11g, 54 Mbps 18 dBm @ 3 % EVM, 802.11a, 54 Mbps Lead free, Halogen Free and RoHS compliant Compact package, 3 x 4 x 0.6 mm, MSL 1 Ordering Information Part No. Package Remark SE5510T SE5510T-R SE5510T-EK1 28 pin QFN 28 pin QFN N/A Samples Tape & Reel Evaluation kit The receive path is designed to maximize performance by providing both a 5 GHz Low noise amplifier with bypass mode, for use when high power signals are being received. Designed for ease of use, all RF ports are matched to 50 Ω to simplify PCB layout and the interface to the transceiver RFIC. The SE5510T also includes a transmitter power detector for each band with 20 dB of dynamic range. Functional Block Diagram CRX5 LEN5 BT PEN5 TX5 5.4 GHz PA 5.4 GHz LNA ANT5 RX5 DET pwr det ANT2 RX2 TX2 2.4 GHz PA CRX2 CBT PEN2 Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 1 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Pin Out Diagram TX5 GND VCC5 VCC4 PEN2 DET LEN5 GND BT 28 27 26 25 24 23 22 21 20 VCC1 1 19 CBT RX5 2 18 ANT5 3 17 RX2 4 16 ANT2 CSP2 5 15 CRX2 GND 11 12 13 14 VCC3 GND CRX5 10 PEN5 9 CSP5 VCC2 TX2 8 DNC 7 GND 6 GND Figure 2: SE5510T Pin Out (Top View Through Package) Pin Out Description Pin No. Name 1 VCC1 2 3 Description Pin No. Name Description Power Supply 16 ANT2 2.4 GHz Antenna port RX5 5 GHz Receive port 17 GND Ground GND Ground 18 ANT5 5 GHz Antenna port 4 RX2 2.4 GHz Receive port 19 CBT Control for Bluetooth port 5 CSP2 2.4 GHz PA bias speed-up 20 BT 6 TX2 2.4 GHz Transmit port 21 GND 7 VCC2 Power supply 22 LEN5 8 GND Ground 23 DET 9 DNC Do Not Connect 10 CSP5 24 PEN2 11 PEN5 25 VCC4 26 VCC5 Power Supply 12 VCC3 5 GHz PA bias speed-up Enable for 5 GHz PA and Transmit switch Power supply Ground Enable for 5 GHz LNA and Receive Switch Power detector output Enable for 2.4 GHz PA and Transmit Switch Power supply 27 GND Ground 13 GND Ground 28 TX5 5 GHz Transmit port 14 CRX5 Control for 5 GHz Receive 15 CRX2 Control for 2.4 GHz Receive Bluetooth port Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 2 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage -0.3 5.5 V VIN Control Pin Voltages -0.3 3.6 V - +10 dBm Operating Temperature Range -40 85 °C Storage Temperature Range -40 150 °C TXRFIN TA TSTG ESD HBM TX2/TX5, with ANT2/ANT5 terminated in 50Ω JEDEC JESD22-A114 All pins V 1000 Recommended Operating Conditions Symbol Parameter Min. Typ. Max. Unit VCC Supply Voltage 2.97 3.3 3.6 V TA Ambient Temperature -40 25 85 °C Control Logic Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Parameter min nom max Units Logic input high : VIH 1.6 3.6 V Logic input low : VIL 0 0.3 V Logic input High current : µA IIH (All except CRX2, CRX5) 1 IIH ( CRX2, CRX5) 50 Logic input Low current : µA IIL (All except CRX2, CRX5) 1 IIL ( CRX2, CRX5) 20 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 3 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End DC Electrical Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Total 802.11g Transmit Supply Current POUT = 20 dBm, 54 Mbps OFDM signal, 64QAM, PEN2 = Hi, POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM, PEN2 = Hi, TXICQ-G Quiescent current , 802.11g Transmit supply Current No RF applied, PEN2=Hi - TXICC-A Total 802.11a Transmit Supply Current POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM, PEN5= Hi POUT = 16 dBm, 54 Mbps OFDM signal, 64QAM, PEN5= Hi - TXICC-G TXICQ-A Quiescent current , 802.11a Transmit supply Current No RF applied, PEN5- Hi RXICC-A Total 802.11a Receive Supply Current CRX5 = Hi, LEN= Hi CRX5 = Hi, LEN = Lo RXICC-G Total 802.11g Receive Supply Current CRX2 = Hi Total BT Supply Current CBT = Hi Total Supply Current No RF, PEN2=PEN5=CRX2=CRX5=CBT=L EN5=0V ICC-BT ICC_OFF Typ. Max. Unit 215 - mA 185 120 - mA 230 mA 210 - 155 - 10 0.25 mA 0.25 mA - 0.25 mA - 5 μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 - mA 4 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Operating Modes Mode# Mode Description PEN2 PEN5 LEN5 CRX2 CRX5 CBT 0 All Off 0 0 0 0 0 0 1 BT 0 0 0 0 0 1 2 BT + RX5(Low gain) 0 0 0 0 1 1 3 BT + RX5(High gain) 0 0 1 0 1 1 4 BT + TX5 0 1 0 0 0 1 5 RX2 + RX5(Low gain) 0 0 0 1 1 0 6 RX2 + RX5(High gain) 0 0 1 1 1 0 7 TX2 1 0 0 0 0 0 8 TX5 0 1 0 0 0 0 9 RX2 0 0 0 1 0 0 10 RX5 (Low Gain) 0 0 0 0 1 0 11 RX5 (High Gain) 0 0 1 0 1 0 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 5 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End AC Electrical Characteristics 2.4 GHz Transmit Characteristics Conditions: VCC = 3.3 V, PEN2= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN POUT S21 S21_OOB ∆S21 Parameter Condition Min. Typ. - 2400 - 18.5 19.5 18 dBm 27.5 dB Frequency Range Output Power, 54 Mbps OFDM, 64 QAM EVM=3% EVM=2.5% Gain 2400 – 2500 MHz Out of Band Gain <2170 MHz Gain Variation Over band 2500 -10 S22 Output Return Loss -10 NF Noise Figure 10 dB dBpp dB -5 dB dB 2f @ Pout= 22 dBm -35 -25 3f 3f @ Pout = 22 dBm -35 -30 ACP11b Spectral Mask 11b @ Pout=22 dBm: fc +/- 11 MHz fc +/- 22 MHz Stability POUT ≤ 23dBm Load VSWR = 4:1 Enable time 10% to 90% of TX RF power, from time that PEN2 is at 50% 11b Harmonics TEN MHz 1.5 Input Return Loss STAB Unit 19 S11 2f Max. dBm/MHz dBc -34 -54 -32 -52 All non-harmonically related outputs less than -45 dBm/MHz 800 nsec Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 6 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End 2.4 GHz Receive Characteristics Conditions: VCC = 3.3V, CRX2 = Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT RX2IL S11 ISOLSW IP1dB TEN Parameter Condition Min. - 2400 - Insertion Loss CRX2= Hi - 1.0 dB RX2 Port Return Loss CRX2= Hi - -14 dB ANT2-RX2, PEN2=Hi 26 CRX2= Hi 15 10% to 90% of RX RF power, from time that CRX2 is at 50% - Frequency Range Switch Isolation Input P1dB Enable Time Typ. Max. 2500 - Unit MHz dB dBm - 800 nsec Bluetooth Characteristics Conditions: VCC = 3.3 V, CBT= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. - 2400 - FOUT Frequency Range BTIL Insertion Loss CBT= Hi - 1.0 S11 BT Port Return Loss CBT= Hi - -14 ANT2-BT, PEN2=Hi 20 - CBT= Hi 15 10% to 90% of BT RF power, from time that CBT is at 50% - ISOLSW IP1dB TEN Switch Isolation Input P1dB Enable Time Max. 2500 Unit MHz dB dB - dB dBm - 800 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 nsec 7 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End 5 GHz Transmit Characteristics Conditions: VCC = 3.3 V, PEN5= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN POUT S21 ∆S21 Parameter Condition Min. Typ. - 4900 - 17.0 18 16 dBm 28 dB Frequency Range Output Power, 54 Mbps OFDM, 64 QAM EVM=3% EVM=2.5% Gain Gain Variation Max. 5850 Over 40 MHz Channel S11 Input Return Loss -14 S22 Output Return Loss -10 2f Harmonics @ Pout=18 dBm MHz 1.5 dBpp -10 dB -5 dB 2f (5150-5300 MHz) 2f (5300-5850 MHz) -40 -50 -35 -42 3f 3f @ Pout = 18 dBm -50 -45 ACP11a Spectral Mask 11a @ Pout=18 dBm: fc +/- 11 MHz fc +/- 20 MHz fc +/- 30 MHz Stability POUT ≤ 21dBm Load VSWR = 4:1 Enable time 10% to 90% of TX RF power, from time that PEN5 is at 50% TEN Unit dBm/MHz dBc -23 -30 -43 -20 -28 -40 All non-harmonically related outputs less than -45 dBm/MHz - - 800 nsec 5 GHz Receive Characteristics Conditions: VCC = 3.3 V, LEN5= Hi, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter FOUT Frequency Range S21 Gain NF IP1dB Condition Min. Typ. - 4900 - dB LEN5 = Lo -7 dB dB - 2.5 Input P1dB LEN5= Hi LEN5=Lo -8 +5 -6 +7 - -10 - - TEN Enable Time MHz 12 LEN5=Hi Input Return Loss 5900 Unit LEN5 = Hi Noise Figure S11 Max. 10% to 90% of RX RF power, from time that - dBm dB 800 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 nsec 8 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Symbol Parameter Condition Min. Typ. Max. Unit LEN5 is at 50% Power Detector Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5510T-EK1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter FOUT Frequency Range PDR Power detect range, peak power PDZLOAD DC load impedance PDVP23 Output Voltage, POUT = 23 dBm PDVP19 Output Voltage, POUT = 19 dBm PDVpnoRF Output Voltage, POUT = No RF PDVAR Power Detector Accuracy vs Load VSWR Condition Min. Typ. PEN2= Hi PEN5 = Hi 2400 4900 - 2500 5900 MHz 0 - 23 dBm - 2.5 Measured at ANT PEN2= Hi Max. Unit kΩ 0.8 1.0 V PEN5= Hi 4950 MHz 5150-5850 MHz 0.4 0.5 0.8 1.0 V - - - V +0.6 dB Pout=20 dBm, 2:1 load VSWR, any angle -1 0.125 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 9 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Package Diagram 28 27 26 25 24 23 22 21 20 20 21 22 23 24 25 26 27 28 1 19 19 1 2 18 18 2 3 17 17 3 4 16 16 4 5 15 15 5 6 7 8 9 10 11 13 12 14 14 13 12 11 10 9 8 7 6 TOP VIEW BOTTOM VIEW Figure 3: Package Outline Drawing Branding Information Pin 1 Identifier Terminal Finish Pin 1 e3 Part Number Lot Code SiGe SE5510T Lot Code Figure 4: SE5510T Branding Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 10 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Recommended PCB Footprint 28 27 26 25 24 23 22 21 28 20 27 26 25 24 23 22 21 20 28 27 26 25 24 23 22 21 20 1 19 1 19 1 19 2 18 2 18 2 18 3 17 3 17 3 17 4 16 4 16 4 16 5 15 5 15 5 15 6 7 8 9 10 11 12 13 14 6 7 8 9 10 11 12 13 14 6 7 8 9 10 11 12 13 14 Figure 5: Recommended pcb footprint Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE5510T is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045. “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 11 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 6: SE5510T-R Tape and Reel Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 12 DATA SHEET SE5510T: Dual Band 802.11n WLAN/BT Front End Document Change History Revision Date Notes 1.0 April-01-2010 Created 1.1 April-05-2010 Added PCB footprint recommendations 1.2 June-14-2010 Updated Pin out and technical specifications 1.3 June-17-2010 Corrected typo on front page, added pin numbers to Fig2 1.4 June-09-2011 Updated specifications and Updated Functional block diagram 1.5 July-06-2011 Updated RX2 isolation specification 1.6 November-21-2011 Updated specifications 1.7 February-03-2012 Updated temperature range, updated tape and reel info 1.8 April-10-2012 Updated with Skyworks logo and disclaimer statement Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202402A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 13