DATA SHEET SKY66111-11: Low-Power Bluetooth® Low Energy Front-End Module for Range Extension Applications Applications VBIAS CTX CRX Range extender VCC Wearable technology Beacons Sensors TR Home automation ANT Internet of Things (IoT) devices Features 203199E-001 Low power consumption: 10 mA @ +10 dBm Figure 1. SKY66111-11 Functional Block Diagram Output: +6 to +13 dBm (single-pin controllable) Supply operation: 1.8 to 5 V Description Low sleep current: < 1 μA The SKY66111-11 is a highly integrated front-end module (FEM) designed for Bluetooth Low Energy (BLE) range extension applications operating in the 2.4 to 2.485 GHz range. RX bypass Small MCM (20-pin, 3.3 x 3.0 x 0.8 mm) package (MSL3, 260 °C per JEDEC-J-STD-020) The device is provided in a 3.3 x 3.0 x 0.8 mm 20-pin MCM package. A functional block diagram is shown in Figure 1. Pin assignments are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. BIAS CTX GND CRX GND GND Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. 20 19 18 17 16 15 14 VCC 13 GND 3 12 GND 4 11 ANT GND 1 GND 2 GND TR 5 6 7 8 9 10 GND GND GND GND GND GND Paddle 203199E-002 Figure 2. SKY66111-11 Pinout (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 1 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Table 1. SKY66111-11 Signal Descriptions1 Pin Name Description Pin Name Description 1 GND Ground 11 ANT Antenna port 2 GND Ground 12 GND Ground 3 GND Ground 13 GND Ground 4 TR Common receive/transmit port 14 VCC Positive power supply 5 GND Ground 15 GND Ground 6 GND Ground 16 GND Ground 7 GND Ground 17 CRX RX control signal 8 GND Ground 18 GND Ground 9 GND Ground 19 CTX Tx control signal 10 GND Ground 20 BIAS PA bias current input, connect to CTX through a resistor 1 The paddle should be connected to ground. See Figure 6. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY66111-11 are provided in Table 2. The recommended operating conditions are specified in Table 3. Electrical specifications are provided in Tables 4 through 8. Table 2. SKY66111-11 Absolute Maximum Ratings1 Parameter Symbol Minimum Maximum Units Supply voltage VCC 5.5 V Control voltages VCTX, VCRX 5.0 V Bias voltage VBIAS 5.0 V RF Input power PIN +20 dBm Voltage standing wave ratio VSWR 10:1 Operating temperature TA –40 +85 °C Storage temperature TSTG –65 +150 °C Electrostatic discharge: ESD 150 V Human Body Model (HBM), Class 0 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Typical 2.4 Maximum Units 2.485 GHz Frequency f Supply voltage VCC 1.8 3 5.0 V Control voltages VCTX, VCRX 1.7 3 VCC V Bias voltage VBIAS 1.25 1.8 VCC Operating temperature TA 25 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E V °C DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Table 4. SKY66111-11 Electrical Specifications: DC Characteristics1 (VCC = VCTX = 3.3 V, VBIAS = 1.8 V, VCRX = 0 V, TA = +25 C, RBIAS (R1) = 0 kΩ, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units RX current (bypass) ICQ_RX RX mode 1 μA TX quiescent current2 ICQ_TX TX mode 6 mA TX operating current2 IOP_TX TX mode (PIN = –1 dBm): 8.5 10 10.5 11 mA mA mA mA 550 μA VCC = 1.8 V VCC = 3.0 V VCC = 3.3 V VCC = 5.0 V TX bias current (BIAS pin) IBIAS_TX Sleep current3 ICC_OFF Sleep mode 0.1 1 μA 1 Performance is guaranteed only under the conditions listed in this table. 2 For total current, IBIAS_TX should be added to the values. 3 VCTX = VBIAS = 0 V. Table 5. SKY66111-11 Electrical Specifications Transmit Characteristics1 (VCC = VCTX = 3.3 V, VBIAS = 1.8 V, VCRX = 0 V, TA = +25 C, PIN = –1 dBm, RBIAS (R1)= 0 kΩ, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units +8 +10 +10.3 +10.8 dBm dBm dBm dBm PIN = –1 dBm 11 dB Over frequency range 0.7 Output power POUT VCC = 1.8 V VCC = 3.0 V VCC = 3.3 V VCC = 5.0 V Saturated gain2 G_SAT Gain slope GSLOPE Input return loss S11 –14 dB Output return loss S22 –10 dB Insertion loss (sleep mode) 2 S21_SLEEP Third order input intercept point2 IIP3 Third order output intercept point2 OIP3 –15 1 –12 dB dB @ 2.44 GHz, ∆ f = ± 1 MHz, PIN = –14 dBm/tone +5 dBm @ 2.44 GHz, ∆ f = ± 1 MHz, PIN = –14 dBm/tone +16 dBm 1 dB input compression point IP1dB –1 dBm 1 dB output compression point OP1dB +10 dBm 2 nd to 10 harmonics2 th RX to TX transition time2 TX power on time2 2fo to 10fo tSWITCH tON TX power off time2 tOFF –30 dBm/MHz 10% to 90% RF 50% VCTX to 90% RF 500 ns 10% to 90% RF 50% VCTX to 90% RF 500 ns 90% to 10% RF 50% VCTX to 10% RF 150 ns 1 Performance is guaranteed only under the conditions listed in this table. 2 Guaranteed by characterization. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 3 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Table 6. SKY66111-11 Electrical Specifications: Receive Characteristics1 (VCC = 3.3 V, VCRX = 3.3 V, VCTX = 0 V, TA = +25 C, PIN = –20 dBm, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Insertion loss S21 Isolation S12 Input return loss S11 Test Condition Min TX Mode (PIN = –20 dBm) Typical Max Units 0.9 dB 25 dB –15 dB Output return loss S22 –15 dB TX to RX transition time2 tSWITCH 10% to 90% RF 50% VCRX to 90% RF 500 ns RX power on time2 tON 10% to 90% RF 50% VCRX to 90% RF 150 ns RX power off time2 tOFF 90% to 10% RF 50% VCRX to 10% RF 150 ns 1 Performance is guaranteed only under the conditions listed in this table. 2 Guaranteed by characterization. Table 7. SKY66111-11 Electrical Characteristics: Logic Characteristics (TA = +25 C) Parameter Voltage logic high1 Voltage logic low Symbol Minimum Maximum Units VHIGH 1.7 5 V VLOW 0 0.2 V 1 Difference between logic high voltages for VCRX and VCTX should not exceed 0.2 V. Table 8. SKY66111-11 Mode Logic Truth Table Mode Sleep mode CTX CRX BIAS 0 0 0 Receive (RX) mode 0 1 0 Transmit (TX) mode 1 0 11 Non-permissible state2 1 1 x 1 Analog voltage control for PA output power. See Figure 3. 2 This state will enable both the TX and RX paths. It is not permitted to operate in this state. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM BIAS Pin Usage The BIAS pin can also be used to adjust the SKY66111-11 output power when the RF source (transceiver or baseband) has a fixed level. 14 12 12 10 10 8 –4 dBm –1 dBm 0 dBm 4 dBm 6 4 1.2 1.5 1.8 2.1 2.4 2.7 3 8 1.3 V 1.4 V 1.5 V 6 4 -10 3.3 -8 -6 -4 VBIAS (V) 4 6 8 10 12 14 12 14 40 35 1.3 V 1.4 V 1.5 V 1.6 V 1.8 V 2.0 V 2.5 V 3.3 V 1.3 V 1.4 V 1.5 V 30 1.6 V 1.8 V 2.2 V 2.5 V 3.3 V 25 PAE (%) 15 10 20 15 5 -5 0 5 10 Output Power (dBm) Figure 5. ICC vs POUT & VBIAS (VCC = 3.3 V) 15 10 203199E-006 203199E-005 ICC + IBIAS (mA) 2 Figure 4. Gain vs POUT & VBIAS (VCC = 3.3 V) 25 0 -10 0 2.5 V 3.3 V Output Power (dBm) Figure 3. POUT vs VBIAS & PIN (VCC = 3.3 V) 20 -2 1.6 V 1.8 V 2.0 V 203199E-004 Gain (dB) 14 203199E-003 POUT (dBm) The SKY66111-11 BIAS pin supplies the bias to the internal PA. By varying the voltage at this pin, PA operating parameters including gain, supply current, and efficiency can be adjusted. 5 0 -10 -8 -6 -4 -2 0 2 4 6 8 10 Output Power (dBm) Figure 6. Power-Added Efficiency vs POUT & VBIAS (VCC = 3.3 V) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 5 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM In many applications, a variable DC supply voltage may not be available. The desired bias voltage can be generated by connecting BIAS to the GPIO controlling CTX with a resistor (refer to Figure 12). With no RF input, the BIAS pin draws approximately 10% of the main supply current. Toggling BIAS from the CTX GPIO 2.5 also causes the PA to turn off when CTX is pulled low, reducing the RX and shutdown mode current. Table 9 lists the relationship between bias voltage/current and bias resistance. 25 3.3 3 IBIAS (mA) 2 20 ICC (mA) 15 1 10 VBIAS (V) 1.5 ICC (mA) IBIAS (mA) 2.7 2.4 2.1 1.8 0.5 203199E-008 5 1.5 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 VBIAS (V) 2.4 2.7 0 3.3 3 203199E-007 Figure 7. IBIAS and ICC vs VBIAS (VCC = 3.3 V, no RF) 1.2 0 3 6 9 12 15 18 21 24 RBIAS (kΩ) Figure 8. VBIAS vs RBIAS (Vcc = 3.3 V) Table 9. Bias Voltage and Current vs Bias Resistance (VCC = 3.3 V) RBIAS (k) VBIAS (V) IBIAS (mA) 0 3.30 2.09 0.47 2.65 1.41 1 2.28 1.03 1.5 2.07 0.82 2.2 1.90 0.64 3.3 1.78 0.48 4.7 1.62 0.36 6.8 1.52 0.26 10 1.44 0.19 15 1.37 0.13 22 1.32 0.09 33 1.29 0.06 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E 27 30 33 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM If a fixed BIAS voltage (for example, from an LDO) is available in the application circuit, using this instead of a resistor reduces the variation of output power with VCC. To minimize SKY66111-11 current consumption in RX bypass and shutdown modes, the voltage to the BIAS pin should be switched off when the CTX is logic low. 14 2.5 V 3.3 V 12 POUT (dBm) 1.6 V 1.8 V 2.0 V 10 8 6 4 1.2 203199E-009 POUT (dBm) 12 1.3 V 1.4 V 1.5 V 1.5 1.8 2.1 2.4 2.7 VCC (V) Figure 9. POUT vs VCC & VBIAS (PIN = −1 dBm) 3 3.3 0Ω 470 Ω 1000 Ω 1500 Ω 2200 Ω 3300 Ω 4700 Ω 6800 Ω 10000 Ω 15000 Ω 22000 Ω 33000 Ω 10 8 6 4 1.2 203199E-010 14 1.5 1.8 2.1 2.4 2.7 3 3.3 VCC (V) Figure 10. POUT vs VCC & RBIAS (PIN = −1 dBm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 7 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Evaluation Board Description Package Dimensions The SKY66111-11 Evaluation Board is used to test the performance of the SKY66111-11 front-end module. The board is optimized for evaluation, experimentation, and investigation with a Bluetooth Low Energy signal source. The design and layout can be quickly and easily transferred into a production design. The PCB layout footprint for the SKY66111-11 is provided in Figure 14. Typical part markings are shown in Figure 15. Package dimensions are shown in Figure 16, and tape and reel dimensions are provided in Figure 17. An Evaluation Board schematic is provided in Figure 11. A reference design schematic is provided in Figure 12. Table 10 provides the Bill of Materials (BOM) list for Evaluation Board components. A photograph of the Evaluation Board is shown in Figure 13. Evaluation Board Setup Procedure Connect Supply 1. Connect J1 and J4 to 50 instruments. Terminate all unused ports (if applicable) with 50 . 2. Connect the supply ground to Pins 1, 4, and 6 of J2. 3. Connect 3.3 V to pin 7 of J2. 4. Connect 1.8 V to one of the logic pins (pin 3 or pin 5) on J2 to select RX or TX mode. For TX mode, also connect pin 2 to 1.8 V. Connect the other logic pin to ground. Refer to Table 8 for mode control settings. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY66111-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Measure Performance TX Monitor the 2.4 GHz amplifier performance by applying an RF signal to connector J4 (TR) and verify the output power on connector J1 (ANT). RX Monitor the 2.4 GHz switch performance by applying an RF signal to connector J1 (ANT) and verify the output signal on connector J4 (TR). CAUTION: Care should be taken not to overdrive the switch by applying too much RF on the input to the device. A starting input power of −20 dBm is suitable for the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM J2 1 BIAS 2 CTX 1 2 2 1 2 16 GND 17 CRX 18 GND 19 GND GND 13 1 GND 12 2 ANT 11 9 6 5 GND TR GND 4 1 SKY66111-11 U1 GND SMA J4 GND 8 3 VCC 7 VCC 14 GND 2 C5 DNI 0402 GND 7 1 CTX 2 R6 DNI 0201 GND 2 1 C7 DNI 0402 BIAS 1 20 R2 DNI 0201 5 6 15 2 CRX R5 0Ω 0201 GND 2 R1 0Ω 0201 1 C3 1 μF 0402 1 2 R3 0Ω 0201 GND C6 DNI 0402 1 3 4 C4 DNI 0402 1 1 2 R4 0Ω 0201 C1 DNI 0201 2 1 1 2 SMA J1 C2 DNI 0201 10 1 203199E-011 CRX CTX Figure 11. SKY66111-11 Evaluation Board Schematic 15 GND 16 GND 17 CRX 18 GND 19 SKY66111-11 U1 GND VCC 14 VCC GND 13 C3 1 μF 0402 GND 12 L4 2.7 nH ANT 11 GND R3 0Ω 0201 C1 1 pF SMA J1 C2 1 pF 10 GND 9 GND 8 7 5 GND TR GND 4 GND GND 3 GND 6 2 CTX 20 1 TX-RX R5 0Ω R2 (RBIAS) 0Ω BIAS Note: Include a footprint for R2 to enable compatibility with both the SKY66110-11 and the SKY66111-11 203199E-012 Figure 12. SKY66111-11 Reference Design Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 9 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Table 10. SKY66111-11 Evaluation Board Bill of Materials (BOM) Component C1, C2 Value Size Manufacturer Mfr Part Number Characteristics DNI 0201 C3 1 μF 0402 C4, C5, C6 DNI 0402 J1, J4 SMA end launch Johnson Components 142-0701-851 SMA end launch straight jack receptacle - tab contact J2 7X1 100 mil Samtec TSW-107-07-G-S 100 mil header Skyworks Solutions Inc. Z720-B Capacitor PCB1 Z720-B R2, R6 DNI 0201 PCB R1 (RBIAS), R3, R4, R5 0Ω 0201 Panasonic ERJ1GE0R00 Thick film chip resistor U1 SKY66111-11 MCM50P300X330-20 Skyworks Solutions Inc. SKY66111-11 Low-power Bluetooth Low Energy ranger extender Do not install Figure 13. SKY66111-11 Evaluation Board Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM 3.6 mm Pin 20 Package Outline Pin 1 Indicator 0.2 x 0.2 Pin 1 Pitch 0.5 mm 3.3 mm 2X 0.85 mm Exposed Center Pad Stencil aperture size of 80% to 100% of the module/package solder mask openings 2X 0.85 mm 20X 0.5 mm 20X 0.25 mm Stencil Aperture Pin 20 3.7 mm Pin 20 3.6 mm Package Outline Pin 1 Pitch 0.5 mm 0.5 mm Pitch Pitch 0.6 mm Package Outline Pin 1 Indicator 0.2 x 0.2 Pin 1 3.4 mm 3.3 mm 2X 0.85 mm Exposed Center Pad Opening size of 60% to 100% of the exposed center opening shown 6X 0.25 mm Thermal via array ø0.3 mm on 0.6 mm pitch improves thermal performance 20X 0.6 mm 20X 0.35 mm 6X 0.5 mm 0.25 mm Min 0.6 mm Pitch 2X 0.85 mm Solder Mask Opening Metallization Notes: 1. All dimensions are in millimeters, unless otherwise specified. 2. Thermal vias should be resin filled and capped in accordance with IPC-4761Type VII vias. Recommended Cu thickness is 30 to 35 μm. 203199E-014 Figure 14. PCB Layout Footprint Pin 1 Indicator SKYWORKS 66111-11 Lot # YYWW MX 203199E-015 Skyworks Part Number Lot Code Date Code: YY = Calendar Year WW = Week CC = Country Code Figure 15. Typical Part Markings Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 11 Top C 4X 0.75 B 4X 0.25 3.3 Pin 1 Indicator 4X 1.25 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Pin 20 Pin 1 Indicator See Detail B Pin 1 20X SMT Pad 0.1 M A B C 4X 0.25 0 3 4X 0.75 14X 1.4 0 A See Detail A 0.8 ± 0.1 0.075 A B C 0.1 Top View Side View 14X 1.55 Solder Mask Opening 0.2 A B C Bottom View 0.7 ± 0.05 1.7 0.2 X 0.2 2X (0.05) 0.5 ± 0.1 1.7 (0.1) Metal Pad Edge 0.5 ± 0.05 Detail A Pad Notes: 4X Scale 6X This Rotation 6X Rotated 180° 4X Rotated 90° CW 4X Rotated 90° CCW 1. All measurements are in millimeters. 2. Dimensions and tolerances according to ASME Y14.5M-1994. 5X R0.05 Max Detail B Pad 2X Scale 1X This Rotation 203199E-016 Figure 16. SKY66111-11 Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E .50 4.00 ±0.10 2.00 ±0.05 +0 –0 .10 .00 3.75 ±0.05 (Bo) A Pin 1 Location A 5° Max 4.00 ±0.10 Ø1.50 B 12.00 ±0.20 B Ø1 5.50 ±0.05 0.25 ±0.05 1.75 ±0.10 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM ±0.10 1.05 ±0.05 (Ko) Section B 5° Max Notes: 1. Carrier tape must meet all requirements of Skyworks GP01-D233 procurement spec for tape and reel shipping. 2. Carrier tape material: black conductive polycarbonate. 3. Cover tape material: transparent conductive material. 4. ESD surface resistivity shall be ≤ 1 x 1010 Ohms/square per EIA, JEDEC TNR specification. 5. 10 -sprocket hole pitch cumulative tolerance on tape: ±0.20 mm. 6. Ao and Bo measured on plane 0.30 mm above the bottom of the pocket. 7. All dimensions are in millimeters. 3.20 ±0.05 (Ao) Section A 203199E-017 Figure 17. SKY66111-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203199E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 22, 2016 13 DATA SHEET • SKY66111-11: LOW-POWER BLUETOOTH LOW ENERGY FEM Ordering Information Model Name SKY66111-11 Manufacturing Part Number SKY66111-11-R Evaluation Board Part Number SKY66111-11-EK1 Copyright © 2015-2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 February 22, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203199E