DATA SHEET ANT_SEL Smart meters In-home appliances Smart thermostats CTX CPS Applications CSD SKY66109-11: 2.4 GHz ZigBee®/Smart Energy Front-End Module Logic control TXP Features PA TXN ANT1 Balun Small MCM (20-pin, 3 x 4 x 0.9 mm) package, NiPdAu-plated (MSL3, 240 °C per JEDEC-J-STD-020) CTX VCC1 CPS CSD Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. 20 19 18 17 GND 1 16 VCC2 TXP 2 15 GND TXN 3 14 ANT_SEL VB_OUT 4 13 GND RXP 5 12 ANT1 RXN 6 11 GND 10 ANT2 9 GND 8 GND VB_IN 7 203034-002 VB_OUT RXP ANT2 RXN Balun LNA 203034-001 VB_IN Integrated PA with up to +22.5 dBm output power Integrated LNA with programmable bypass Integrated antenna switching with transmit and receive diversity function Low noise figure: 2 dB typical Differential transmit/receive interface with integrated baluns Fast switch on/off time: <800 ns Supply range: 2.0 V to 3.6 V Sleep mode current: 0.05 μA typical No bias resistor is required Figure 1. SKY66109-11 Functional Block Diagram Description The SKY66109-11 is a high-performance, fully integrated RF front-end module (FEM) designed for ZigBee®/Smart Energy applications. The SKY66109-11 is designed for ease of use and maximum flexibility. The device provides integrated and fully matched input baluns, an integrated interstage matching and harmonic filter, and digital controls compatible with 1.6 to 3.6 V CMOS levels. The RF blocks operate over a wide supply voltage range from 2.0 V to 3.6 V that allows the SKY66109-11 to be used in battery powered applications over a wide spectrum of the battery discharge curve. The SKY66109-11 is provided in a small, 20-pin, 3 x 4 mm MultiChip Module (MCM) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. SKY66109-11 Pinout (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 1 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Table 1. SKY66109-11 Signal Descriptions Pin Name Description Pin Name Description 1 GND Ground 11 GND Ground 2 TXP Positive transmit input signal from transceiver, 200 Ω differential 12 ANT1 Connect to 50 Ω antenna 3 TXN Negative transmit input signal from transceiver, 200 Ω differential 13 GND Ground 4 VB_OUT Transmit balun bias core supply from transceiver (optional connection) 14 ANT_SEL Connect to GPIO signal to control antenna switch (see Table 7) 5 RXP Positive receiver output signal to transceiver, 200 Ω differential 15 GND Ground 6 RXN Negative receiver output signal to transceiver, 200 Ω differential 16 VCC2 Connect to positive supply 7 VB_IN Receive balun bias core supply from transceiver (optional connection) 17 CSD Connect to GPIO signal for mode control (see Table 6) 8 GND Ground 18 CPS Connect to GPIO signal for mode control (see Table 6) 9 GND Ground 19 VCC1 Connect to positive supply 10 ANT2 Connect to 50 Ω antenna 20 CTX Connect to GPIO signal for mode control (see Table 6) +1.8 V VB_IN VREG_OUT FEM Optional Output Filter 2n7 SoC 1 pF 1 pF VB_OUT VDD_PA 1 kΩ each series resistor, placed close to the SKY66109 pins. CPS CSD CTX Internal Lattice Balun 1.8 V Differential source or load impedance symbol Input Input Decoupling capacitor on chip 1.8 V 1.8 V VBIAS_IN The balun at the FEM PA input (or LNA output) can also be used to inject a bias operating point for the transceiver output stage (the shunt inductor provides a DC path on the other side). The inductor also tunes out any parasitic capacitance. If the SOIC transceiver does not require a DC bias, leave the VB_IN open. 203034-003 Figure 3. Injecting a Bias Operating Point for the Transceiver Output Stage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Electrical and Mechanical Specifications The state of the SKY66109-11 is determined by the logic provided in Tables 6 and 7. The absolute maximum ratings of the SKY66109-11 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Tables 4 and 5. Table 2. SKY66109-11 Absolute Maximum Ratings1 Parameter Symbol Supply voltage VCC1 Supply voltage VCC2 Control pin voltages Minimum Maximum Units –0.3 +3.6 V –0.3 +3.82 V –0.3 +3.6 V Transmit output power at ANT1 or ANT2 port into 50 Ω load POUT_TX_MAX +22.5 dBm Transmit input power at the TXN and TXP ports PIN_TX_MAX +6 dBm Receive input power at ANT1 or ANT2 ports, LNA mode PIN_RX_MAX +10 dBm Receive input power at ANT1 or ANT2 ports, bypass mode PIN_RX_BYPASS_MAX +15 dBm Operating temperature TA –40 +125 C Storage temperature TSTG –40 +125 C Electrostatic discharge: ESD 1000 V Human Body Model (HBM), Class 1C 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. 2 Vcc2 is restricted to +3.6 V when operated at TA = 125 C. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industrystandard ESD handling precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Typical 1.6 Maximum Units 3.6 V Supply voltage for balun bias VB_IN, VB_OUT Supply voltage on VCC pins VCC1, VCC2 2.0 3.0 3.6 V Operating temperature TA –40 +25 +125 C Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 3 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Table 4. SKY66109-11 Electrical Specifications1 (VCC1 = VCC2 = 3.0 V, TA = +25 C, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units DC Characteristics mA mA mA 110 90 45 Total supply current ICC_TX POUT = +20 dBm POUT = +17 dBm2 POUT = +10 dBm2 Total supply current ICC_RX Total supply current ICC_RX_BYPASS Sleep supply current ICC_OFF No RF 0.05 Quiescent current Icq No RF 30 5 7 mA 300 μA 1.00 μA mA Logic Characteristics Control voltage: High Low VIH VIL Control current: High Low IIH IIL 1.6 0 3.6 0.3 V V 1 1 μA μA Dual Antenna Switch Characteristics Isolation between ANT1 and ANT2 ports ISOLANTSW –20 dB ANT1 to ANT2 switching time tANT1_ANT2 400 ns 1 Performance is guaranteed only under the conditions listed in this table. 2 Not tested in production. Fully characterized and guaranteed by design. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Table 5. SKY66109-11 Electrical Specifications1 (VB_IN = VB_OUT = 1.6 to 3.6 V, VCC1 = VCC2 = 3.0 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 2483 MHz AC Transmit Characteristics Frequency range f Output power at ANT1 or ANT2 port POUT 2400 VCC1 = VCC2 =: 3.6 V 3.3 V 3.0 V 2.7 V 2.0 V +22.5 +21.0 +20.5 +20.0 +17.0 21 Small signal gain S21 PIN = –25 dBm Small signal gain variation ΔS21 Across all ZigBee channels 17 dBm dBm dBm dBm dBm dB 2 dBp-p Saturated gain G_SAT POUT = +20 dBm 2nd harmonic 2fo POUT = +20 dBm, IEEE 802.15.4 source 19 –42 dBm/MHz 3rd harmonic2 3fo POUT = +20 dBm, IEEE 802.15.4 source –42 dBm/MHz Output return loss2 S22 ANT1 or ANT2 port –5 dB Transmit port impedance2 ZIN Turn-on time2 tRISE –10 dB Ω 200 From 50% of CTX edge to 90% of final RF output power 800 ns 800 ns Turn-off time2 tFALL From 50% of CTX edge to 10% of final RF output power Stability2 Stab CW, Pin = 0 dBm, 0.1 GHz to 20 GHz, load VSWR = 6:1 All non-harmonically related outputs < –42 dBm/MHz – Ruggedness2 RU CW, Pin = +6 dBm, load VSWR = 10:1 No permanent damage – AC Receive Characteristics Frequency range f Receive gain RX_GAIN Receive noise figure2 NF 2400 2483 MHz 10.5 dB 2 dB Third order input intercept point2 IIP3 –3 +1 dBm 1 dB input compression point IP1dB –13 –3 dBm 1 dB input compression point in bypass mode2 IP1dB Input return loss2 S11 ANT1 or ANT2 ports –10 Receive port impedance2 ZOUT Measured differentially between RXP and RXN 200 Turn-on time2 +10 tRISE Turn-off time2 tFALL Gain in bypass mode G_BP dBm From 50% of CTX edge to 90% of final RF output power –5 Ω 800 From 50% of CTX edge to 10% of final RF output power dBm 800 –3 ns ns dB 1 Performance is guaranteed only under the conditions listed in this table. 2 Not tested in production. Fully characterized and guaranteed by design. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 5 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Table 6. SKY66109-11 Mode Control Logic1 (VCC1 = VCC2 = 3.0 V, TA = +25 C) Mode Description All off (sleep mode)2 0 CPS (Pin 18) CSD (Pin 17) CTX (Pin 20) Typical Current Consumption X 0 X 0.1 μA 1 Receive bypass mode 0 1 0 250 μA 2 Receive LNA mode 1 1 0 5 mA 4 Transmit mode X 1 1 30 mA 1 “0” = 0 V. “1” = +3.0 V. “X” = don’t care (must be either 0 V or Vcc voltage). Any state other than described in this table places the switch into an undefined state. An undefined state will not damage the device. 2 Remove EVB pulldown resistors to achieve specified sleep current with CTX or CPS high. Table 7. SKY66109-11 Antenna Enable Logic1 (VCC1 = VCC2 = 3.0 V, TA = +25 C) CPS (Pin 18) CSD (Pin 17) CTX (Pin 20) ANT_SEL (Pin 14) ANT1 port enabled X X X 0 ANT2 port enabled X X X 1 Description 1 “0” = 0 V. “1” = +3.0 V. “X” = don’t care. Any state other than described in this table places the switch into an undefined state. An undefined state will not damage the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Evaluation Board Description Package Dimensions The SKY66109-11 Evaluation Board is used to test the performance of the SKY66109-11 FEM. The board is optimized for evaluation, experimentation, and investigation with an 802.15.4 signal source. The design and layout can be quickly and easily transferred into a production design. The PCB layout footprint for the SKY66109-11 is provided in Figure 7. Typical part markings are shown in Figure 8. Package dimensions for the 20-pin MCM are shown in Figure 9, and tape and reel dimensions are provided in Figure 10. An Evaluation Board schematic diagram is provided in Figure 4. A reference design schematic is provided in Figure 5. Table 8 describes the pins on the power and control I/O header (J5). Table 9 provides the Bill of Materials (BOM) list for Evaluation Board components. The Evaluation Board is shown in Figure 6. Evaluation Board Setup Procedure 1. Connect J1, J2, J3, and J4 to 50 Ω instruments. Terminate all unused ports (if applicable) with 50 Ω. 2. Connect the supply ground to pins 19 and 20 of J5. 3. Connect 3.0 V to pins 15 and 16 of J5. 4. Connect 3.0 V to pins 3 and 4 of J5. NOTE: Pins 7 and 8 of J5 are left open. NOTE: By following the logic in Table 6, the required RF path is selected. Refer to Table 7 for antenna port control. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY66109-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 240 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. 5. Monitor the 2.5 GHz amplifier transmit performance by applying an RF signal to J3 and monitoring the output power on J1 (ANT1) or J2 (ANT2). CAUTION: Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device. A suitable starting input power would be –20 dBm. 6. Monitor the 2.5 GHz amplifier receive performance by applying an RF signal to J1 (ANT1) or J2 (ANT2) and monitoring the output signal on J3. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 7 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM J5 1 2 VCC 3 4 VDD VB_OUT 5 6 VB_OUT VB_IN 7 8 VB_IN 9 10 CTX 11 12 CPS 13 14 CSD 15 16 VCC2 17 18 ANTSEL 19 20 VCC VDD C2 2.2 μF C1 2.2 μF VCC C4 100 nF C8 10 pF CPS CTX R2 100K 1 UN_BAL 2 RF_GND 3 BAL_PT C5 10 pF VCC2 20 CTX 19 VCC1 18 CPS 17 CSD Pad 21 R3 100K J3 SMA C3 100 nF 6 N/C 5 GND 4 BAL_PT U2 VB_OUT 1 GND 2 TXP 3 TXN 4 VB_OUT 5 RXP SKY66109-11 U1 VCC2 GND ANT_SEL GND ANT1 6 RXN 14 13 12 C7 10 pF 11 ANTSEL R4 100K U3 J1 SMA 7 8 9 10 C6 10 pF 6 N/C 5 GND 4 BAL_PT GND 16 15 VB_IN GND GND ANT2 1 UN_BAL 2 RF_GND 3 BAL_PT J4 SMA R1 100K CSD VB_IN J2 SMA Figure 4. SKY66109-11 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G 203034-004 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM VCC C4 100 nF C8 10 pF CPS CSD VCC Pad 20 CTX 19 VCC1 18 CPS 17 CSD 21 CTX C3 100 nF TXP 1 GND 2 TXP 3 TXN L2 TXN SKY66109-11 U1 GND ANT_SEL GND 4 VB_OUT 5 RXP 6 RXN VB_OUT RXP L1 VCC2 ANT1 GND 16 15 14 C7 10 pF ANTSEL 13 12 11 ANT1 7 8 9 10 VB_IN GND GND ANT2 RXN VB_IN ANT2 203034-005 Figure 5. SKY66109-11 Reference Design Schematic Table 8. Power and Analog I/O Header: J5, 10x2 Pin Pin Name Description Recommended Setting 1, 2, 15 VCC Supply voltage General purpose VCC provided as the main power supply 3, 4, 9, 11, 13, 17 VDD Digital supply voltage Connect to separate power supply voltage 5, 6 VB_OUT Bias output – 7, 8 VB_IN Bias voltage input No connect 16 VCC2 Supply voltage General purpose VCC provided as the main power supply 10 CTX Control 12 CPS Control 14 CSD Control 18 ANT_SEL Control 19, 20 GND Ground See Tables 6 and 7 General purpose ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 9 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Table 9. SKY66109-11 Evaluation Board Bill of Materials (BOM) Component Value Size Manufacturer Manufacturer Part Number Characteristics C1, C2 2.2 μF 0805 Murata GRM21BR71A225KA01L Ceramic capacitor, 2.2 μF, 10V, 10%, X7R 0805 C3, C4 100 nF 0402 Murata GRM155R71C104KA88D Monolithic ceramic C5, C6, C7, C8 10 pF 0402 Murata GRM1555C1H100JZ01 Multilayer ceramic J1, J2, J3, J4 SMA End launch Johnson Components 142-0701-851 SMA end launch straight jack receptacle – tab contact J5 10X2 100 mil Samtec TSW-110-07-G-D 100 mil header R1, R2, R3, R4 100 kΩ 0402 Panasonic ERJ2GEJ104 Thick film chip resistor U1 – 3 x 4 mm MCM Skyworks Solutions, Inc. SKY66109-11 2.4 GHz ZigBee FEM with differential transmit/receive – 2 x 1.25 mm TDK HHM1521 Multilayer 2.4 GHz chip baluns U2, U3 Note: Schematic and BOM have been designed to optimize performance in 802.11a/n applications. 203034-006 Figure 6. SKY66109-11 Evaluation Board Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM 4.3 mm Stencil aperture size for center ground pad should be 80% to 100% (by area) of the solder mask opening 20X 0.56 mm 20X 0.25 mm 0.5 mm Pitch 3.3 mm 4X 0.59 mm Package Outline Pin 20 Pin 1 Indicator 0.20 X 45° Pin 1 2X 0.4375 mm 2X 0.513 mm Stencil Aperture Top View 4.4 mm 4.3 mm 2.1045 mm 20X 0.66 mm 20X 0.35 mm 14X 0.56 mm 14X 0.25 mm 0.5 mm Pitch 0.5 mm Pitch 3.4 mm 2X 0.59 mm 3.3 mm Package Outline Package Outline Pin 20 Pin 1 Indicator 0.20 X 45° Pin 1 Pin 20 Thermal via array Ø0.3 mm on 0.6 mm pitch improves thermal performance Pin 1 Note: Opening size of 60% to 100% of exposed center opening shown Solder Mask Opening Top View Metallization Top View Thermal vias should be resin filled and capped in accordance with IPC-4761 Type VII vias. Recommended Cu thickness is 30 to 35 µm. 203034-007 Figure 7. PCB Layout Footprint Pin 1 Indicator Line 1 Line 3 NOTE: 203034-008 Line 2 Lines 1, 2, and 3 have a maximum of 7 characters Line 1 = Part Number and Version Line 2 = Lot Number Line 3 = YEAR-WEEK-Country Code (MX) Figure 8. Typical Part Markings Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 11 Top B 20X SMT Pad 0.1 M A B C C Solder Mask Opening 0.2 A B C 0.577 0 0.577 4 8X 1.9 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM A 4X 0.25 3 0 0.15 A B C 0.1 Top View Side View (0.1) 0.25 ±0.05 Pin 20 Pin 1 Indicator See Detail C Pin 1 Bottom View 1.026 0.875 0.31 ±0.1 0.35 ±0.05 4X 0.75 See Detail B A 0.95 ±0.1 4X 0.25 Pin 1 Indicator 4X 1.25 4X 0.75 12X 1.4 5X R0.05 Max 4X R0.05 Max 1.18 1.18 (0.05) Metal Pad Edge Detail A Pad Scale: 2X 4X This Rotation 4X Rotated 180° 0.2 X 45° Solder Mask Edges Solder Mask Edges Detail B Detail C Pad Scale: Full 1X This Rotation Pad Scale: Full 1X This Rotation Notes (Unless Otherwise Specified): 1. Dimensions and tolerances are in accordance with ASME Y14.5M–1994. 2. Dimensions are in millimeters. Figure 9. SKY66109-11 Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G 203034-009 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM 8.00 ∅1.5 +0.1/–0.0 4.00 (Note 1) 1.75 ± 0.10 ∅1.50 Min A 5.50 ± 0.05 (Note 3) R0.3 Max. 4.40 12.0 ± 0.30 2.00 ± 0.05 (Note 3) 0.30 ± 0.05 A 0.12 1.10 A Pin 1 Indicator 3.40 0.12 Notes: R0.25 1. 10 sprocket hole pitch cumulative tolerance ±0.2 mm. 2. Camber in compliance with EIA 481. 3. Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole. 4. All measurements are in millimeters. 203034-010 Figure 10. SKY66109-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 13 DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM Ordering Information Model Name SKY66109-11: Zigbee/Smart Energy FEM Manufacturing Part Number SKY66109-11 Evaluation Board Part Number SKY66109-11-EK1 Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G