DATA SHEET SKY73421-11: 1400 to 2000 MHz Broadband, Application Configurable High Gain and Linearity Diversity Downconversion Mixer Applications IFA+ 2G/3G/4G base station transceivers: GSM/EDGE, CDMA, UMTS/WCDMA, LTE Land mobile radio High performance radio links IFA– RLOA BS0 RIFA BS1 RFA Features LO Operating frequency range: 1400 to 2000 MHz IF frequency range: 150 to 320 MHz Conversion gain: 9 dB Input IP3: up to +29.5 dBm Output IP3: up to +38.5 dBm Noise Figure: 9 dB Power-down mode Integrated LO drivers Integrated low loss RF baluns High linearity IF amplifiers Application tuneability Small, QFN (36-pin, 6 x 6 mm) package (MSL3, 260 C per JEDEC J-STD-020) Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. RFB PWRDN RIFB IFB+ IFB– RLOB S2760 Figure 1. SKY73421-11 Block Diagram Description The SKY73421-11 is a fully integrated diversity mixer that includes Local Oscillator (LO) drivers, high linearity mixers, and large dynamic range Intermediate Frequency (IF) amplifiers. Low loss RF baluns have also been included to reduce design complications and lower system cost. The SKY73421-11 features an IIP3 of +25 dBm and a Noise Figure (NF) of 9 dB, making the device an ideal solution for high dynamic range systems such as 2G/3G/4G base station receivers. The SKY73421-11 has been designed for optimum long-term reliability. The SKY73421-11 diversity downconversion mixer is provided in a compact, 36-pin Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 1 VCC_RFA RIFA N/C IFA– IFA+ N/C VCC_IFA RLOA N/C DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER 36 35 34 33 32 31 30 29 28 RFA 1 27 N/C GND 2 26 N/C GND 3 25 BS1 VCC_LO 4 24 BS0 Ground Pad GND RFB 9 19 LO 10 11 12 13 14 15 16 17 18 N/C VCC_LOIN 20 RLOB 21 8 N/C 7 GND VCC_IFB GND IFB– PWRDN IFB+ N/C 22 N/C 23 6 RIFB 5 VCC_RFB N/C VCC_LO S2761 Figure 2. SKY73421-11 Pinout – 36-Pin QFN (Top View) Table 1. SKY73421-11 Signal Descriptions Pin # 1 Name RFA Description RF channel A input Pin # 19 Name LO Description Local oscillator input 2 GND Ground 20 GND Ground 3 GND Ground 21 VCC_LOIN DC supply, +5 V 4 VCC_LO DC supply, +5 V 22 PWRDN Power-down mode enable 5 N/C No internal connection 23 N/C No internal connection 6 VCC_LO DC supply, +5 V 24 BS0 Band select 0 control 7 GND Ground 25 BS1 Band select 1 control 8 GND Ground 26 N/C No internal connection 9 RFB RF channel B input 27 N/C No internal connection 10 VCC_RFB DC supply, +5 V 28 N/C No internal connection 11 RIFB IF channel B bias control 29 RLOA LO channel A bias control 12 N/C No internal connection 30 VCC_IFA DC supply, +5 V 13 IFB+ IF channel B positive output 31 N/C No internal connection 14 IFB– IF channel B negative output 32 IFA+ IF channel A positive output 15 N/C No internal connection 33 IFA– IF channel A negative output 16 VCC_IFB DC supply, +5 V 34 N/C No internal connection 17 RLOB LO channel B bias control 35 RIFA IF channel A bias control 18 N/C No internal connection 36 VCC_RFA DC supply, +5 V – Ground pad Bottom ground pad (Note 1) Note 1: Bottom ground pad serves as a key electrical and thermal ground. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Functional Description LO Buffers The SKY73421-11 is a high gain diversity mixer, optimized for base station receiver applications. The device consists of two diversity channels, each consisting of a low loss RF balun, high linearity passive mixer, and a low noise IF amplifier. The LO buffers allow the input power of the SKY73421-11 to be driven in the range of –6 to +6 dBm. The LO section has been optimized for 1250 to 1900 MHz. However, the LO can be driven over a wide frequency range with only slight degradation in performance. The SKY73421-11 also includes a power-down feature used to lower the supply current for standby operation (refer to Tables 4 and 5): PWRDN Logic: Mixer State: High Standby (low power mode) Low Full operation LO amplifiers are also included that allow the SKY73421-11 to connect directly to the output of a Voltage Controlled Oscillator (VCO). This eliminates the extra gain stages needed by most discrete passive mixers. RF Baluns and Passive Mixer The RF baluns provide a single ended input, which can easily be matched to 50 Ω using a simple matching circuit. The RF baluns offer very low loss and excellent amplitude and phase balance over a wide frequency range of 1200 to 2000 MHz. The high linearity mixer is a passive, double balanced mixer that provides a very low insertion loss, and excellent 3rd Order Input Insertion Point (IIP3) and linearity performance. Additionally, the balanced nature of the mixer provides for excellent port-to-port isolation. Bandselect Logic Pins 17 (RLOB) and 29 (RLOA) allow for external biasing of the LO driver bias currents to trade off linearity for the core passive mixer current. Power-Down Mode The SKY73421-11 also includes a low current power-down mode controlled by pin 22 (PWRDN). When this pin is at a logic high level, the power-down function is enabled with the total mixer current under 45 mA. PWRDN does not have an internal pull up or pull down. IF Amplifier The SKY73421-11 includes high dynamic range IF amplifiers that follow the passive mixers in the signal path. The outputs require a supply voltage connection using inductive chokes. These choke inductors should be high-Q and have the ability to handle 200 mA or greater. A simple matching network allows the output ports to be matched to a balanced 200 impedance. The IF amplifiers are optimized for IF frequencies between 100 and 350 MHz. The IF amplifiers can be operated outside of this range, but with a slight degradation in performance. Pins 11 (RIFB) and 35 (RIFA) allow for external biasing of the IF amplifier bias currents to trade off linearity for the IF amplifer current. The SKY73421-11 is designed to optimize performance in four sub-bands. The particular sub-band of interest is selected by setting pin 24 (BS0) and pin 25 (BS1). The bandselect logic is provided in Table 2. Electrical and Mechanical Specifications Depending on the LO injection side, and the RF and IF frequencies involved, there could be multiple bandselect solutions. Table 5 identifies recommended bandselects for a number of frequency ranges. The absolute maximum ratings of the SKY73421-11 are provided in Table 3. The recommended operating conditions are specified in Table 4 and electrical specifications are provided in Tables 5 and 6. Table 2. SKY73421-11 Bandselect Logic BS1 (Pin 25) BS0 (Pin 24) LO Center Frequency (MHz) 0 0 1250 0 1 1500 1 0 1700 1 1 1750 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 3 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Table 3. SKY73421-11 Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units 4.5 5.5 V Supply voltage, +5 V (VCC_LO, VCC_RFA, VCC_RFB, VCC_IFA, VCC_IFB, VCC_LOIN) VCC Total supply current: IFA+ (pin 32) IFA– (pin 33) IFB+ (pin 13) IFB– (pin 14) VCC_LO (pin 4) VCC_LO (pin 6) VCC_LOIN (pin 21) VCC_IFA (pin 30) VCC_IFB (pin 16) ICC 360 32 32 32 32 82 82 28 20 20 mA mA mA mA mA mA mA mA mA mA RF input power PRF +20 dBm LO input power PLO Operating case temperature TC Junction temperature TJ Storage case temperature TSTG Thermal resistance ΘJC Electrostatic discharge: ESD –40 –40 Charged Device Model (CDM), Class 4 Human Body Model (HBM), Class 1C Machine Model (MM), Class A +20 dBm +100 C +125 C +150 C 10.4 C/W 1000 1000 50 V V V Notes: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 4. SKY73421-11 Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units RF frequency range fRF 1425 1980 MHz LO frequency range fLO 1100 1900 MHz 350 MHz 5.25 V IF frequency range fIF 100 Supply voltage, +5 V VCC 4.75 Supply current (Note 1), PWRDN = 0 V ICC LO input power PLO Logic levels (Note 2): high low VIN_H VIN_L Logic input current IL Operating case temperature (Note 3) TC 5.00 310 –6 0 1.09 0 mA +6 dBm VCC 0.74 V V 0 –40 mA +100 Note 1: With RIFA/B and RLOA/B bias resistors to ground = 8.2 kΩ. Note 2: Logic signals are: PWRDN, BS0, and BS1. Valid logic levels must be applied. There are no internal pull-ups or pull-downs. Note 3: Case temperature measured at bottom of package where device is soldered to board. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B C DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Table 5. SKY73421-11 Electrical Specifications (Note 1) (VCC = 4.75 to 5.25 V, TC = –40 to +100 C, PLO = –3 to +3 dBm, PWRDN = Logic “0,” BS0/BS1 = Logic “1,” PRF = –10 dBm, fIF = 200 MHz, Unless Otherwise Noted) Test Condition Parameter Symbol Conversion gain Operating current BS1 BS0 Min Typical Max Units 1427 to 1463 high side 1 1 7.5 9.8 dB 1710 to 1785 low side 1 0 7.5 9.2 dB 1850 to 1915 low side 1 1 7.5 8.9 dB 7.5 1920 to 1980 low side 1 1 1427 to 1463 high side 1 1 8.4 8.8 11.0 dB dB 1710 to 1785 low side 1 0 8.7 11.0 dB 1850 to 1915 low side 1 1 9.1 11.0 9.3 11.0 NF 3rd Order Input Intercept Point (two tones, 800 kHz separation) 3RF – 3LO LO Injection G Noise Figure 2RF – 2LO RF Frequency Range (MHz) IIP3 1920 to 1980 low side 1 1 1427 to 1463 high side 1 1 +23.5 +25.0 dBm 1710 to 1785 low side 1 0 +23.5 +25.9 dBm +23.5 +26.1 dBm +29.5 dBm +25.7 dBm 1850 to 1915 low side 1 1 1850 to 1980 (Note 2) low side 1 1 1920 to 1980 low side 1 1 1427 to 1463 high side 1 1 –69 –63 dBc 1710 to 1785 low side 1 0 –70 –63 dBc 1850 to 1915 low side 1 1 –74 –63 dBc 1920 to 1980 low side 1 1 –74 –63 dBc 1427 to 1463 high side 1 1 –99 –70 dBc 1710 to 1785 low side 1 0 –99 –70 dBc 1850 to 1915 low side 1 1 –88 –70 dBc 1920 to 1980 low side 1 1 –88 –70 dBc 1427 to 1463 high side 1 1 310 325 mA 1710 to 1785 low side 1 0 294 310 mA 1850 to 1915 low side 1 1 302 315 mA 1920 to 1980 low side 1 1 308 325 mA +23.5 2x2 3x3 ICC_ON Note 1: Performance is guaranteed only under the conditions listed in this Table. Production tested: RF frequency = 1880 MHz, LO frequency= 1680 MHz. All others guaranteed by design and characterization. Testing conducted with balun on IF output (see Figure 5). Table 1 performance is of the DUT, with balun loss de-embedded. Input matching can be unique for each bandselect setting. Conditions for typical values: VCC = 5 V, TC = +35 C, PLO = 0 dBm, middle of RF range. The following bias resistors are used for the corresponding frequencies. Each of the fRF ranges have their own RF/LO/IF matching: fRF = 1427 to 1463 MHz, high side LO injection: RIF = 8.2 kΩ, RLO = 8.2 kΩ fRF = 1710 to 1785 MHz, low side LO injection: RIF = 2 kΩ, RLO = 8.2 kΩ fRF = 1850 to 1920 MHz, low side LO injection: RIF = 2 kΩ, RLO = 18 kΩ fRF = 1920 to 1980 MHz, low side LO injection: RIF = 1 kΩ, RLO = DNI RIF bias resistors (RIFA and RIFB) are noted R31 and R35 on schematic and Evaluation Board. RLO bias resistors (RLOA and RLOB) are noted R29 and R37 on schematic and Evaluation Board. Note 2: External bias resistors for IF and LO (RIF and RLO of Note 1) are not installed. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 5 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Table 6. SKY73421-11 Electrical Specifications (Note 1) (VCC = 4.75 to 5.25 V, TC = –40 to +100 C, PLO = –3 to +3 dBm, PWRDN = Logic “0,” BS0/BS1 = Logic “1,” PRF = –10 dBm, fIF = 200 MHz, Unless Otherwise Noted) Parameter Symbol Noise Figure with a blocker signal (Note 2) NFBLK Input 1 dB compression point IP1dB Test Condition Min Blocking signal input power = +8 dBm, 5 MHz offset Typical Max Units 21 25 dB +10.0 +12.6 dBm Channel-to-channel isolation 40 57 dB RF to IF isolation 30 66 dB LO leakage: 1xLO to RF port 2xLO to RF port 3xLO to RF port 4xLO to RF port 1xLO to IF port Power-down current IOFF PWRDN = 1 –44 –38 –56 –56 –60 –25 –25 –28 –25 –23 dBm dBm dBm dBm dBm 37 45 mA Power-up time (Note 2) (Note 3) tON 0.42 1 μs Power-down time (Note 2) (Note 4) tOFF 0.10 1 μs RF port input return loss (Note 2) ZIN_RF With external matching components 14 dB LO port input return loss (Note 2) ZIN_LO With external matching components 14 dB IF port input return loss (Note 2) ZOUT_IF With external matching components 14 dB Note 1: Performance is guaranteed only under the conditions listed in this Table. Production tested: RF frequency = 1880 MHz, LO frequency= 1680 MHz. All others guaranteed by design and characterization. Testing conducted with balun on IF output (see Figure 5). Table 1 performance is of the DUT, with balun loss de-embedded. Input matching can be unique for each bandselect setting. Conditions for typical values: VCC = 5 V, TC = +35 C, PLO = 0 dBm, middle of RF range. The following bias resistors are used for the corresponding frequencies and each of the fRF ranges have their own RF/LO/IF matching: fRF = 1427 to 1463 MHz, high side LO injection: RIF = 8.2 kΩ, RLO = 8.2 kΩ fRF = 1710 to 1785 MHz, low side LO injection: RIF = 2 kΩ, RLO = 8.2 kΩ fRF = 1850 to 1920 MHz, low side LO injection: RIF = 2 kΩ, RLO = 18 kΩ fRF = 1920 to 1980 MHz, low side LO injection: RIF = 1 kΩ, RLO = DNI RIF bias resistors are noted R31 and R35 on schematic and Evaluation Board. RLO bias resistors are noted R29 and R37 on schematic and Evaluation Board. Note 2: Not production tested. Guaranteed by design and characterization. Note 3: Time required for IF envelope to reach 90% of final value following a PWRDN transition to logic “0” with tFALL < 1 ns. Note 4: Time required for IF envelope to reach 10% of final value following a PWRDN transition to logic “1” with tRISE < 1 ns. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Evaluation Board Description The SKY73421-11 Evaluation Board is used to test the performance of the SKY73421-11 downconversion mixer. An assembly drawing for the Evaluation Board is shown in Figure 3 and the layer detail is provided in Figure 4. A schematic diagram of the SKY73421-11 Evaluation Board is shown in Figure 5. Circuit Design Considerations The following design considerations are general in nature and must be followed regardless of final use or configuration: 6. Components R29, R33, R34, and R37 (see Figure 5) allow for external adjustment of the LO driver bias currents. Skyworks recommends that these resistors have a tolerance of ±1 percent to optimize performance consistency of the SKY73421-11. These resistors are optional for device operation, but the performance in Tables 5 and 6 is specified for the values of the RLO resistors (R29 and R37) as indicated in the Tables. 7. It is recommended to apply solder paste with stencil, as noted in Figure 6. 1. Paths to ground should be made as short as possible. 2. The ground pad of the SKY73421-11 has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the device. Therefore, design the connection to the ground pad to dissipate the maximum wattage produced by the circuit board. 3. Skyworks recommends including external bypass capacitors on the VCC voltage inputs of the device. 4. Components L12, L13, L14, and L15 (see Figure 5) are high-Q low loss inductors. These inductors must be able to pass currents in excess of 200 mA DC. 5. Components R8, R9, R31, and R35 (see Figure 5) allow for external adjustment of the IF amplifier bias currents. Skyworks recommends that these resistors have a tolerance of 1% to optimize performance consistency of the SKY73421-11. These resistors are optional for device operation, but the performance in Tables 5 and 6 is specified for the values of the RIF resistors (R31 and R35) as indicated in the Tables. Package Dimensions The PCB layout footprint for the SKY73421-11 is provided in Figure 6. Figure 7 shows the package dimensions for the 36-pin QFN and Figure 8 provides the tape and reel dimensions. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. THE SKY73421-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design & SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 7 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER J6 J7 J4 J1 J3 S2988 Figure 3. SKY73421-11 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Top Layer Ground Plane Power Plane Bottom Layer S2989 Figure 4. SKY73421-11 Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 9 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER 1 R24 0Ω L2 39 nH 6 3 4 2 3 C1 2.2 μF Chan. A IF Output C24 7.5 pF 1 +5 V Supply J6 2 +5 V Supply J2 T1 C37 DNI L14 390 nH +5 V Supply L15 390 nH +5 V Supply +5 V Supply Channel A IF Bias R9 DNI C23 15 pF R31 2 kΩ C11 2.2 nF C53 470 nF C47 2.2 μF R33 DNI +5 V Supply C33 22 pF C39 2.7 nH J7 36 3 4 +5 V Supply × C19 15 pF 5 6 7 8 +5 V Supply C2 2.2 nF C18 15 pF 10 L3 1.5 pF +5 V Supply N/C N/C BS1 BS0 N/C PWRDN VCC_LOIN GND LO 27 26 25 +5 V Supply R12 100 kΩ × J5 24 23 22 × × R2 DNI × 1 × 2 +5 V Supply R13 100 kΩ 21 +5 V Supply 20 C14 33 pF 19 C16 1 μF J4 LO Input 11 12 13 14 15 16 17 18 Chan. B Input R1 100 kΩ R21 DNI 35 34 33 32 31 30 29 28 RFA GND GND VCC_LO N/C VCC_LO GND GND RFB C30 22 pF C27 2.7 nH J1 9 R29 8.2 kΩ × VCC_RFA RIFA N/C IFA– IFA+ N/C VCC_IFA RLOA N/C 1 × VCC_RFB RIFB N/C IFB+ IFB– N/C VCC_IFB RLOB N/C L8 DNI 2 C5 2.2 nF × Bottom Ground Pad Chan. A Input L9 1.5 pF +5 V Supply Channel A LO Bias C25 15 pF C13 22 pF × Channel B LO Bias L4 DNI +5 V Supply R34 DNI R37 8.2 kΩ +5 V Supply +5 V Supply C20 15 pF C22 15 pF C10 2.2 nF C54 470 nF C48 2.2 μF Channel B IF Bias +5 V Supply R8 DNI R35 2 kΩ L12 390 nH +5 V Supply L13 390 nH 1 T1 6 R19 0Ω L1 39 nH J3 Chan. B IF Output 2 +5 V Supply 3 4 C21 7.5 pF C36 DNI Notes: Some component labels may be different than the corresponding component symbol shown here. Component values, however, are accurate as of the date of this Data Sheet. Y0067 Figure 5. SKY73421-11 Evaluation Board Schematic Table 7. RF and IF Matching Components Band Selects RF Range (MHz) IF Matching Components (IF = 200 MHz) RF Matching Components IF Bias LO Bias BS1 BS0 R2 R12 L9, L3 C39, C27 L8, L4 C33, C30 L2, L1 C24, C21 R24, R19 C37, C36 R31, R35 R29, R37 1427 to 1463 1 1 100 kΩ DNI DNI 22 pF 8.2 nH 22 pF 27 nH 6.8 pF 0Ω DNI 8.2 kΩ 8.2 kΩ 1710 to 1785 1 0 DNI 100 kΩ 1.5 pF 2.7 nH DNI 22 pF 39 nH 7.5 pF 0Ω DNI 2 kΩ 8.2 kΩ 1850 to 1915 1 1 100 kΩ DNI 1.5 pF 2.2 nH DNI 11 pF 39 nH 7.5 pF 0Ω DNI 2 kΩ 18 kΩ 1920 to 1980 1 1 100 kΩ DNI 1.2 pF 2.2 nH DNI 5.1 pF 39 nH 7.5 pF 0Ω DNI 1 kΩ DNI Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B 9X 2.03 9X 1.52 9X 1.02 Pin 36 6.40 4.60 9X 2.03 9X 1.52 9X 1.02 9X 0.51 0 9X 0.51 9X 1.02 9X 1.52 9X 2.03 6.40 4.60 0.650 Typ. 0.250 Typ. 0.500 Typ. 2 3 0 7 20 81X ∅0.25 0 Pin 1 Board Metal Pin 36 6.50 4.40 Pin 1 9X 0.51 0 9X 0.51 9X 1.02 9X 1.52 9X 2.03 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Via Pattern (Note 1) 6.40 Pin 36 0.20 Typ. Pin 1 3X 1.20 0.20 Typ. 0.20 Typ. 6.50 4.40 6.40 3X 1.20 0.20 Typ. 0.750 Typ. 0.350 Typ. 0.500 Typ. Solder Mask Pattern (Note 2) NOTES: 1. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), soldermask on the far side should tent or plug via holes. 2. Soldermask recommendations: Contact board fabricator for recommended soldermask offset and tolerance. 3. Stencil recommendations: 0.125 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release. Component Outline 0.650 Typ. 0.250 Typ. 0.500 Typ. 67% solder coverage on center pad Stencil Pattern (Note 3) Dimension and tolerancing according to ASME Y14.5M-1994. Unless specified, dimensions are symmetrical about center lines. All dimensions are in millimeters. S3158 Figure 6. PCB Layout Footprint for the SKY73421-11 6 x 6 mm QFN Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 11 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER 0.850 ± 0.050 2X A 6.000 ± 0.050 0.15 C B 36 35 34 33 32 4.600 ± 0.050 0.10 M C A B See Note 3 0.40 x 45° 0.203 Ref. 31 30 29 28 28 29 30 31 32 33 34 35 36 27 27 1 2 26 26 2 3 25 25 3 4 24 24 4 5 23 23 5 6 22 22 6 7 21 21 7 8 20 20 9 0.15 C 4.600 ± 0.050 6.000 ± 0.050 0.10 M C A B 1 19 10 11 12 13 14 15 16 17 Seating Plane 0 to 0.05 2X c Top View 8 R0.075 Typ. 19 18 18 17 16 15 14 13 9 12 11 10 36 X 0.250 ± 0.050 36X 0.400 ± 0.050 0.10 M C A B 0.05 M C Side View Bottom View NOTES: 1. All measurements are in millimeters. 2. Dimensioning and tolerancing according to ASME Y14.5M-1994. Unless otherwise specified the following values apply: Decimal Tolerance: Angular Tolerance: X.X (1 place) ± 0.1 mm ±1° X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 3. Terminal #1 identification mark located within marked area. 4. Unless specified, dimensions are symmetrical about center lines. Figure 7. SKY73421-11 36-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 0.500 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B S2944 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER P2 2.00 ± 0.1 (Note 1) ∅1.55 ± 0.05 (Do) 0.30 ± 0.05 Po 4.00 ± 0.1 (Note 2) E1 1.75 ± 0.1 Y 6.30 ± 0.1 (Bo) A Ref 3° . CL 16.00 ± 0.3 ∅1.5 Min. (D1) 7.50 ± 0.1 (Note 1) Pin 1 Location 1.10 ± 0.1 (Ko) Y 12.00 ± 0.1 (P1) Section Y-Y 6.30 ± 0.1 (Ao) Ref. R0.5 Notes: 1. Measured from center line of sprocket hole to center line of pocket. 2. Cumulative tolerance of 10 sprocket holes is ± 0.20 mm. 3. Other material available. Detail A S2943 All measurements are in millimeters. Figure 8. SKY73421-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202965B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 8, 2013 13 DATA SHEET • SKY73421-11 DOWNCONVERSION MIXER Ordering Information Model Name SKY73421-11 1400-2000 MHz Downconversion Mixer Manufacturing Part Number SKY73421-11 Evaluation Board Part Number SKY73421-11-EK1 (1427.9 to 1462.9 MHz) SKY73421-11-EK3 (1710 to 1785 MHz) SKY73421-11-EK2 (1850 to 1915 MHz) SKY73421-11-EK4 (1920 to 1980 MHz) Copyright © 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 November 8, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202965B