DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications General Description Features The AAT3175 is a low noise, constant frequency charge pump DC/DC converter that uses a tri-mode load switch (1X), fractional (1.5X), and doubling (2X) conversion to maximize efficiency for white LED flash applications. The AAT3175 is capable of driving up to three flash LEDs at 300mA total current from a 2.7V to 5.5V input. A low external parts count (two 1μF flying capacitors and two small 1μF capacitors at VIN and VOUT) make this part ideally suited for small battery-powered applications. • VIN Range: 2.7V to 5.5V • Up to 300mA Total Flash Current • Fully Programmable Current with Single Wire ▪ 16 Logarithmic Current Levels • Tri-Mode 1X, 1.5X, and 2X Charge Pump for Maximum Efficiency and VF Coverage • Drives 3-in-1 or 2-in-1 Flash LEDs ▪ 0.5% Current Matching • No Inductors, Low Noise Operation • 1MHz Constant Switching Frequency • Small Application Circuit • Built-In Thermal Protection • Automatic Soft-Start • IQ <1μA in Shutdown • TDFN33-12 Package Skyworks’ S2Cwire™ (Simple Serial Control™) serial digital input is used to enable, disable, and set current for all LEDs with 16 level settings down to 0. The AAT3175 is equipped with built-in protection for VOUT short-circuit condition and auto-disable for load shortcircuit condition on any one of the channels. Built-in softstart circuitry prevents excessive inrush current during start-up. A low-current shutdown feature disconnects the load from VIN and reduces quiescent current to less than 1μA. Applications • Programmable Current Sinks • White LED Backlighting • White Photo Flash for Mobile Phones The AAT3175 is available in a Pb-free, space-saving, thermally-enhanced 12-pin 3×3mm TDFN package. Typical Application C1+ C2+ C1 1μF 2.7V to 5.5V C1- C2- VIN VOUT CIN 1μF D1 AAT3175 GND D2 D3 COUT 1μF D1 D2 EN/SET EN/SET D3 D4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 1 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Pin Descriptions Pin # Symbol 1 2 3 4 D4 EN/SET C1+ C1- 5 VOUT 6 7 8 9 10 11 12 EP C2+ C2VIN GND D1 D2 D3 Function Current sink input #4; 100mA max. S2Cwire serial interface control pin. Flying capacitor 1 positive terminal. Connect a 1μF capacitor between C1+ and C1-. Flying capacitor 1 negative terminal. Charge pump output to drive load circuit. Requires 1μF capacitor connected between this pin and ground. Flying capacitor 2 positive terminal. Connect a 1μF capacitor between C2+ and C2-. Flying capacitor 2 negative terminal. Input power supply. Requires 1μF capacitor connected between this pin and ground. Ground. Current sink input #1; 100mA max. Current sink input #2; 50mA max. Current sink input #3; 50mA max. Exposed paddle (bottom). Connect to GND directly beneath package. Pin Configuration TDFN33-12 (Top View) D4 EN/SET C1+ C1VOUT C2+ 2 1 12 2 11 3 10 4 9 5 8 6 7 D3 D2 D1 GND VIN C2- Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Absolute Maximum Ratings1 Symbol VIN VEN/SET IOUT2 TJ TLEAD Description Input Voltage EN/SET to GND Voltage Maximum DC Output Current Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec.) Value Units -0.3 to 6 -0.3 to VIN + 0.3 300 -40 to 150 300 V V mA °C °C Value Units 2.0 50 W °C/W Thermal Information3 Symbol PD JA Description Maximum Power Dissipation4 Maximum Thermal Resistance 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Based on long-term current density limitation. 3. Mounted on an FR4 board. 4. Derate 20mW/°C above 25°C. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 3 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Electrical Characteristics1 CIN = COUT = C1 = C2 = 1.0μF; TA = -40°C to +85°C, unless otherwise noted. Typical values are TA = 25°C, VIN = 3.5V. Symbol Description Conditions Input Power Supply Operation Range VIN ICC Operating Current ISHDN Shutdown Current IDX I(D-Match) ISINK Average Current Accuracy Current Matching2 1X to 1.5X or 1.5X to 2X TransiVTH tion Threshold at Any ISINK Pin Charge Pump Section TSS Soft-Start Time FCLK Clock Frequency EN/SET VEN(L) Enable Threshold Low VEN(H) Enable Threshold High TEN/SET LO EN/SET Low Time TEN/SET HI MIN Minimum EN/SET High Time TEN/SET HI MAX Maximum EN/SET High Time TOFF EN/SET Off Timeout TLAT EN/SET Latch Timeout IEN/SET EN/SET Input Leakage Min Typ 2.7 1X Mode, 3.0 ≤ VIN ≤ 5.5, Active, No Load Current 1.5X Mode, 3.0 ≤ VIN ≤ 5.5, Active, No Load Current 2X Mode, 3.0 ≤ VIN ≤ 5.5, Active, No Load Current EN/SET = 0 D1, D4 Max Setting D2, D3 Max Setting VF:D1:D4 = 3.6V, D2 and D3 in Parallel VIN = 2.7V VIN = 5.5V 0.3 1.0 2.0 90 45 100 50 0.5 Max Units 5.5 1.0 3.0 3.7 1.0 110 55 5.0 V mA μA mA % 250 mV 100 1000 μs kHz 0.4 1.4 0.3 75 50 -1 75 500 500 1 V V μs ns μs μs μs μA 1. The AAT3175 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. Current matching is defined as the deviation of any sink current from the average of all active channels. 4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Typical Characteristics CIN = COUT = C1 = C2 = 1μF, TA = 25°C, VIN = 3.5V, unless otherwise noted. Efficiency vs. Supply Voltage 300mA LED Pulse (VIN = 3.8V) 100 Efficiency (%) 90 80 60mA VF = 3.0V VOUT (2V/div) 70 150mA VF = 3.2V 60 50 IOUT (200mA/div) 40 30 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 Time (100ms/div) Supply Voltage (V) Turn-On to 1X Mode Turn-On to 1.5X Mode (VIN = 4.2V; 300mA Load) (VIN = 4.0V; 300mA Load) EN (2V/div) EN (2V/div) VOUT (2V/div) VOUT (2V/div) VSINK (1V/div) VSINK (1V/div) IIN (400mA/div) IIN (400mA/div) Time (200μ μs/div) Time (200μ μs/div) Turn-On to 2X Mode Turn-Off from 1.5X Mode (VIN = 3.8V; 300mA Load) (VIN = 4.0V; 300mA Load) EN (2V/div) EN (2V/div) VF (1V/div) VOUT (2V/div) VSINK (1V/div) IIN (200mA/div) IIN (400mA/div) Time (200μ μs/div) Time (200μ μs/div) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 5 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Typical Characteristics CIN = COUT = C1 = C2 = 1μF, TA = 25°C, VIN = 3.5V, unless otherwise noted. Line Response Load Characteristics (1.5X Mode; 150mA Load) (VIN = 3.5V; 1.5X Mode; 150mA Load) 4.2V VIN (500mV/div) 3.7V VOUT (500mV/div) 3.6V VSINK (500mV/div) VIN (100mV/div) VOUT (100mV/div) VSINK (100mV/div) ILED (10mA/div) Time (1ms/div) Time (500ns/div) Load Characteristics Input Ripple vs. Input Voltage (VIN = 3.0V; 2X Mode; 150mA Load) (150mA Load) 30 Input Ripple (mV) VIN (100mV/div) VOUT (100mV/div) VSINK (100mV/div) 25 20 15 10 5 0 Time (500ns/div) 3.3 3.5 3.8 4.0 4.3 4.5 400 300 -40°C 200 150 25°C 85°C 50 0 EN/SET Off Timeout (µs) EN/SET Latch Timeout (µs) 6 3.0 EN/SET Off Timeout vs. Input Voltage 350 100 2.8 Input Voltage (V) EN/SET Latch Timeout vs. Input Voltage 250 2.5 350 300 -40°C 250 200 150 25°C 85°C 100 50 0 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 Input Voltage (V) Input Voltage (V) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Typical Characteristics CIN = COUT = C1 = C2 = 1μF, TA = 25°C, VIN = 3.5V, unless otherwise noted. 1.2 1.1 1 -40°C 0.9 0.8 0.7 0.6 25°C 85°C 0.5 0.4 0.3 0.2 Enable Threshold Low vs. Input Voltage Enable Threshold Low (V) Enable Threshold High (V) Enable Threshold High vs. Input Voltage 1.2 1.1 1 0.9 -40°C 0.8 0.7 0.6 0.5 25°C 85°C 0.4 0.3 0.2 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 Input Voltage (V) Input Voltage (V) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 7 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Functional Block Diagram C1+ C1- C2+ C2- 1X, 1.5X, 2X Charge Pump VIN VOUT Soft Start Control 1MHz Oscillator D/A Voltage Reference 6 x 16 bit ROM EN/SET S2Cwire Interface D/A D1 D/A D2 D/A D3 D/A D4 D/A GND Functional Description The AAT3175 is a tri-mode load switch (1X) and high efficiency (1.5X or 2X) charge pump device intended for white LED flash applications. To maximize power conversion efficiency, an internal sensing circuit monitors the voltage required on each constant current sink input and sets the load switch and charge pump modes based on the input battery voltage and the current sink input voltage. As the battery discharges over time, the AAT3175 charge pump is enabled when any of the four current sink inputs nears dropout. The charge pump initially starts in 1.5X mode. If the charge pump output droops enough for any current source output to become close to dropout, the charge pump will automatically transition to 2X mode. The AAT3175 requires only four external components: two 1μF ceramic capacitors for the charge pump flying capacitors (C1 and C2), one 1μF ceramic input capacitor (CIN), and one 0.33μF to 1μF ceramic charge pump output capacitor (COUT). The four constant current sink inputs (D1 to D4) can drive four individual LEDs with a maximum current of 50mA each for D2 and D3. D1 and D4 are driven by two 8 parallel current sources, resulting in a maximum of 100mA each. Unused sink inputs are connected to VOUT; otherwise, the part will operate only in 2X charge pump mode. The S2Cwire serial interface enables the AAT3175 and sets the current sink magnitudes. The D1~D4 current configuration is optimized to drive either 2-in-1 LEDs by combining D1/D2, D3/D4, or 3-in-1 LEDs by combining D2/D3. Constant Current Output Level Settings The constant current sink levels for D1 to D4 are set via the serial interface according to a logarithmic scale where each code is 1dB lower than the previous code. In this manner, LED brightness appears linear with each increasing code count. Because the inputs D1 to D4 are true independent constant current sinks, the voltage observed on any single given input will be determined by the actual forward voltage (VF) for the LED being driven. Since the input current sinks of the AAT3175 are programmable, no PWM (pulse width modulation) or additional control circuitry is needed to control LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to “set it and forget it.” Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications With its high-speed serial interface (1MHz data rate), the input sink current of the AAT3175 can be changed successively to brighten or dim LEDs in smooth transitions (e.g., to fade-out) or in abrupt steps, giving the user complete programmability and real-time control of LED brightness. The S2Cwire serial interface has flexible timing. Data can be clocked-in at speeds greater than 1MHz, or much slower, such as 15kHz. After data is submitted, EN/SET is held high to latch the data. Once EN/SET has been held in the logic high state for time TLAT, the programmed current becomes active and the internal data register is reset to zero. For subsequent current level programming, the number of rising edges corresponding to the desired code must be entered on the EN/SET pin. S2Cwire Serial Interface The current level magnitude is controlled by Skyworks' S2Cwire serial interface. The interface records rising edges of the EN/SET pin and decodes them into 16 different states. The 16 current level settings available are indicated in Table 1. Data D2, D3 IOUT (mA) D1, D4 IOUT (mA) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 50 44 40 36 32 28 25 22 20 17 16 14 13 11 10 0 100 88 80 72 64 56 50 44 40 34 32 28 26 22 20 0 When EN/SET is held low for an amount of time greater than TOFF, the AAT3175 enters into shutdown mode and draws less than 1μA from VIN. The internal data register is reset to zero during shutdown. Auto-Disable Feature The AAT3175 is equipped with an auto-disable feature for each LED channel. After the IC is enabled and started up, a test current of 150μA (typical) is forced through each sink channel. The channel will be disabled if the voltage of that particular DX pin does not fall below a certain threshold. This feature is very convenient for disabling an unused channel or during an LED fail-short event. Thermal Protection The AAT3175 has a built-in thermal protection circuit that will shut down the charge pump if the die temperature rises above the thermal limit, as is generally the case during a short-circuit of the VOUT pin. Table 1: Current Level Settings. S2Cwire Serial Interface Timing THI TLO TOFF T LAT EN/SET 1 Data Reg 2 n-1 0 n ≤ 16 n 0 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 9 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Applications Information LED Selection Although the AAT3175 is specifically intended for driving white LEDs, the device can also be used to drive most types of LEDs with forward voltage specifications ranging from 2.0V to 4.1V. LED applications may include display backlighting, camera photo-flash applications, color (RGB) LEDs, infrared (IR) diodes for remotes, and other loads benefiting from a controlled output current generated from a varying input voltage. Since the D1 to D4 input current sinks are matched with negligible voltage dependence, the LED brightness will be matched regardless of the specific LED forward voltage (VF) levels. In some instances (e.g., in high luminous output applications such as photo flash), it may be necessary to drive high-VF type LEDs. The low dropout current sinks in the AAT3175 make it capable of driving LEDs with forward voltages as high as 4.1V at full current from an input supply as low as 3.5V. Outputs can be paralleled to drive high-current LEDs without complication. Device Switching Noise Performance The AAT3175 operates at a fixed frequency of approximately 1MHz to control noise and limit harmonics that can interfere with the RF operation of cellular telephone handsets or other communication devices. Back-injected noise appearing on the input pin of the charge pump is 20mV peak-to-peak, typically ten times less than inductor-based DC/DC boost converter white LED backlight solutions. The AAT3175 soft-start feature prevents noise transient effects associated with inrush currents during start-up of the charge pump circuit. Capacitor Selection Careful selection of the four external capacitors CIN, C1, C2, and COUT is important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used; generally, low ESR may be defined as less than 100m. A value of 1μF for all four capacitors is a good starting point when choosing capacitors. If the LED current sources are only programmed for light current levels, then the capacitor size may be decreased. ed over all other types of capacitors for use with the AAT3175. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is nonpolarized. Low-ESR ceramic capacitors help maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. Equivalent Series Resistance ESR is an important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material composition, and ambient temperature. Capacitor ESR is typically measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. Ceramic Capacitor Materials Ceramic capacitors less than 0.1μF are typically made from NPO or C0G materials. NPO and C0G materials generally have tight tolerance and are very stable over temperature. Larger capacitor values are usually composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors (i.e., greater than 2.2μF) are often available in low-cost Y5V and Z5U dielectrics, but capacitors greater than 1μF are not typically required for AAT3175 applications. Capacitor area is another contributor to ESR. Capacitors that are physically large will have a lower ESR when compared to an smaller capacitor made of equivalent material. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size. Evaluation Board Description The AAT3175 evaluation board demonstrates the functionality of the AAT3175 and its application as a white LED flash driver. A schematic of the complete circuit is shown in Figure 1; Figures 2 and 3 depict the actual board layout. Table 2 gives the component listing Capacitor Characteristics Ceramic composition capacitors are highly recommend- 10 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications DC+ DC- J1 DC+ U1 AAT3175 C1 1µF 1 2 3 4 5 6 C3 1µF D3 D2 D1 GND VIN C2- D4 EN/SET C1+ C1VOUT C2+ 12 11 10 9 8 7 C4 1µF C2 1µF JPx GND D1 GND R7 220 J2 R6 100K DC+ GND R3 R2 R1 1K 1K 1K DATA 0 2 4 SW3 1 3 5 FLASH 0 2 4 MOVIE 0 2 4 SW2 1 3 5 C5 10µF U2 1 2 3 4 VDD GP5 GP4 GP3 PIC12F675 VSS GP0 GP1 GP2 8 7 6 5 VR4 POT 10K R4 330 SW1 1 3 5 GND R5 330 LED7 RED GND LED0 GRN GND GND Figure 1: AAT3175 Evaluation Board Schematic. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 11 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Figure 2: AAT3175 Evaluation Board Top Layer (not to scale). Component Part# U1 AAT3175 U2 PIC12F675 D1 R1 – R3 C1 – C4 J1, J2 LED0 LED7 C5 R4, R5 R6 R7 JPx JP7, JP8 VR4 SW1 – SW3 LMFLC4500 Chip Resistor GRM188R61A105KA93D PRPN401PAEN CMD15-21UGC/TR8 CMD15-21SRC/TR8 GRM31CR70J106KA01L Chip Resistor Chip Resistor Chip Resistor Chip Resistor Chip Resistor EVN-5ESX50B14 PTS645TL50 Figure 3: AAT3175 Evaluation Board Bottom Layer (not to scale). Description High Efficiency 1X/1.5X/2X CP for White LED; TDFN33-12 Package 8-bit CMOS, FLASH-based μC; 8-pin PDIP package 4-Die, 2-Pin, High Luminosity LED 1kΩ, 5%, 1/4W; 1206 1μF, 10V, X5R, 10%; 0603 Connecting. Header, 2mm Zip Green LED; 1206 Red LED; 1206 10μF, 6.3V, X7R, 10%; 1206 330Ω, 5%, 1/4W; 1206 100kΩ, 5%, 1/4W; 1206 220Ω, 5%, 1/4W; 1206 0Ω, 5%; 0603 0Ω, 5%; 0805 10K POT; 3mm Squared SMD Switch Tact, SPST, 5mm Manufacturer Skyworks Microchip Lumimicro Vishay Murata Sullins Electronics Chicago Miniature Lamp Chicago Miniature Lamp Murata Vishay Vishay Vishay Vishay Vishay Panasonic-ECG ITT Industries Table 2: AAT3175 Evaluation Board Component Listing. 12 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 DATA SHEET AAT3175 High Efficiency 1X/1.5X/2X Charge Pump for White LED Flash Applications Ordering Information Package Marking1 Part Number (Tape and Reel)2 TDFN33-12 QAXYY AAT3175IWP-T1 Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. Package Information TDFN33-123 Index Area 0.40 ± 0.05 Detail "A" 0.45 ± 0.05 2.40 ± 0.05 3.00 ± 0.05 0.1 REF C0.3 3.00 ± 0.05 1.70 ± 0.05 Top View Bottom View 0.23 ± 0.05 Pin 1 Indicator (optional) 0.05 ± 0.05 0.23 ± 0.05 0.75 ± 0.05 Detail "A" Side View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 3. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. Copyright © 2012, 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202101B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • March 5, 2013 13