PRELIMINARY DATA SHEET SKY87608: 28 V, 3 A Non-Synchronous Step-Down Converter Applications Description • Set-top boxes The SKY87608 is a step-down DC-DC converter that operates with a wide 4.5 V to 28 V input voltage range and regulates the output voltage as low as 0.9 V while supplying up to 3 A to the output. The 450 kHz switching frequency allows for an efficient step-down regulator design. • Distributed power systems • Industrial applications Features • 4.5 V to 28 V input voltage • Up to 97% efficiency • Internal 180 mΩ high-side N-channel MOSFET • Internal 12 Ω refresh MOSFET • Up to 3 A load current • Adjustable output voltage (0.9 V to 0.8 × VIN) • Fixed 450 kHz switching frequency • 4 ms soft-start period • External compensation • Less than 1 µA shutdown current The SKY87608 uses an adjustable output voltage that can be set from 12% to 80% of the input voltage by an external resistive voltage divider. Internal soft-start prevents excessive inrush current without requiring an external capacitor. The SKY87608 includes input under-voltage and overcurrent protection to prevent damage in the event of a fault condition. Thermal overload protection prevents damage to the SKY87608 or circuit board when operating beyond its thermal capability. The SKY87608 is available in a small Pb-free, 8-pin, SOP-8L-EP package. A typical application circuit is shown in Figure 1. The pin configuration is shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. • Current limit protection • Standard 8-pin SOP-8L package (MSL1, 260 °C per JEDEC-JSTD-020) with exposed pad Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 1 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Figure 1. SKY87608 Typical Application Circuit Figure 2. SKY87608 8-Pin SOP-8L (Top View) Table 1. SKY87608 Signal Descriptions Pin # Name 1 IN Input supply. Connect IN to the input power source. Bypass IN to GND with a 10 μF or greater ceramic capacitor. IN connects to the source of the internal high-side N-channel MOSFET and linear regulators powering the controller and drivers. Description 2 LX Inductor switching. LX is internally connected to the source of the internal high-side N-channel MOS- FET, the high-side driver, and current-sense circuitry. Connect to the power inductor, and the Schottky diode as shown in the Typical Application Circuit diagram. 3 NC Do NOT connect externally. Leave pin floating. 4 GND Ground. GND is internally connected to the analog ground of the control circuitry, and the source of the 12 Ω refresh MOSFET. 5 FB 6 COMP 7 EN Enable input. Logic high enables the regulator. A logic low forces the SKY87608 into shutdown mode, placing the output into a high-impedance state and reducing the quiescent current to less than 1 μA. 8 BST Boot-strapped high-side driver supply. Connect a 0.1 μF ceramic capacitor between BST and LX as shown in the Typical Application Circuit diagram. – EP Exposed paddle. Connect to PCB ground plane. Feedback input. FB senses the output voltage for regulation control. Connect a resistive divider network from the output to FB to GND to set the output voltage accordingly. The FB regulation threshold is 0.9 V for the SKY87608. Compensation pin of the error amplifier. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Electrical and Mechanical Specifications Typical performance characteristics of the SKY87608 are illustrated in Figures 3 through 24. The absolute maximum ratings of the SKY87608 are provided in Table 2. Thermal information is provided in Table 3, and electrical specifications are provided in Table 4. Table 2. SKY87608 Absolute Maximum Ratings (Note 1) Symbol Minimum Maximum Units IN to GND voltage Parameter VIN –0.3 +30 V LX to GND voltage VLX –0.3 VIN + 0.3 V BST to GND voltage VBST VCC – 0.6 VIN + 6 V EN to GND voltage VEN –0.3 +30 V FB to GND voltage VFB –0.3 +6 V VCOMP –0.3 +6 V COMP to GND voltage Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY87608 Thermal Information (Note 1) (Note 2) Parameter Operating ambient temperature Operating junction temperature Maximum soldering temperature (at leads, 10 seconds.) Symbol Minimum TA –40 TJ –40 Typical Maximum Units +85 °C +150 °C TLEAD 300 °C Maximum junction-to-ambient thermal resistance θJA 41 °C/W Maximum power dissipation (Note 3) PD 2.8 W SKY87608 SOP-8L-EP Thermal Impedance Note 1: Performance is guaranteed only under the conditions listed in this Table. Note 2: Mounted on 1 inch2 FR4 board. Note 3: Derate 27 mW/°C above 25 °C. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 3 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Table 4. SKY87608 Electrical Specifications (Note 1) (VIN = 12 V, VEN = 5 V, AGND = PGND, TA = –40 °C to 85 °C, Typical Values are at TA = 25 °C, Unless Otherwise Noted) Parameter Symbol Test Condition Input voltage VIN No load supply current IQ No load current; not switching Shutdown current ISHDN EN = GND, VIN = 28 V Output voltage (Note 2) VOUT Min Typical Max 28 V 1.6 3.2 mA 1 5 µA 4.5 0.9 Nominal feedback voltage 0.8 × VIN 0.9 FB accuracy VFB No load, VIN = 24 V 0.88 FB leakage current IFB FB = 1.5 V or GND –0.2 Load regulation ∆VOUT / IOUT VIN = 12 V, VOUT = 5 V Line regulation ∆VOUT / VIN VIN = 4.5 V to 28 V Oscillator frequency fOSC Minimum on-time tON(MIN) 0.90 0.92 V +0.2 µA % 0.5 450 % 520 260 Maximum duty cycle DMAX No Load 80 83 High-side MOSFET “on” resistance RDS(ON)HI IN to LX 40 180 Peak current limit threshold IPK 3.75 5.0 Refresh MOSFET “on” resistance RDS(ON)LO LX to GND Input under-voltage lockout VUVLO VIN rising, hysteresis = 200 mV Over-temperature shutdown threshold TSHDN Rising edge, hysteresis = 15 °C EN input logic threshold VEN EN input current IEN Soft-start period tSS VIN = 24 V % 320 mΩ A Ω 4.2 160 V °C 0.4 1.7 V –2.0 40 µA 4 Note 1: Performance is guaranteed only under the conditions listed in this Table. Note 2: The minimum output voltage must be greater than tON(MIN) × fOSC × VIN(MIN) due to duty cycle limitations. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 kHz ns 12 3.5 V V 1.0 380 Units May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B ms PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Typical Performance Characteristics Figure 3. Efficiency vs Output Current (VOUT = 3.3 V) Figure 4. Efficiency vs Output Current (VOUT = 5.0 V) Figure 5. Efficiency vs Output Current (VOUT = 15 V) Figure 6. Load Regulation (VOUT = 3.3 V) Figure 7. Load Regulation (VOUT = 15 V) Figure 8. Line Regulation (VOUT = 3.3 V) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 5 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Typical Performance Characteristics Figure 9. Line Regulation (VOUT = 15 V) Figure 10. Oscillator Frequency vs Temperature (IOUT = 100 mA) Figure 11. Feedback Voltage Error vs Temperature Figure 12. Quiescent Current vs Input Voltage (Switching; No Load) Figure 13. High Side MOSFET On-Resistance vs Input Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Typical Performance Characteristics Figure 14. Soft Start (VOUT = 5 V, VIN = 12 V, IOUT = 100 mA) Figure 15. Soft Start (VOUT = 5 V, VIN = 24 V, IOUT = 100 mA) Figure 16. Soft Start (VOUT = 5 V, VIN = 12 V, IOUT = 3 A) Figure 17. Soft Start (VOUT = 5 V, VIN = 24 V, IOUT = 3 A) Figure 18. Output Voltage Ripple (VOUT = 5 V, VIN = 12 V, IOUT = 100 mA) Figure 19. Output Voltage Ripple (VOUT = 5 V, VIN = 24 V, IOUT = 100 mA) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 7 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Typical Performance Characteristics Figure 20. Output Voltage Ripple (VOUT = 5 V, VIN = 12 V, IOUT = 3 A) Figure 21. Output Voltage Ripple (VOUT = 5 V, VIN = 24 V, IOUT = 3 A) Figure 22. Load Transient (VOUT = 5 V, VIN = 12 V, IOUT = 0.1 to 3 A) Figure 23. Load Transient (VOUT = 5 V, VIN = 24 V, IOUT = 0.1 to 3 A) Figure 24. Load Transient (VOUT = 15 V, VIN = 24 V, IOUT = 0.1 to 3 A) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Figure 25. SKY87608 Functional Block Diagram Functional Description Voltage Soft-Start A functional block diagram is provided in Figure 25. The soft-start circuit ramps the reference voltage from ground up to the 0.9 V nominal feedback regulation voltage (see Figure 25). The internal soft-start capacitor sets the soft-start period as 4 ms (typical). Control Scheme The SKY87608 is a non-synchronous, fixed-frequency, currentmode step-down converter. The regulator includes an internal high-side N-channel MOSFET capable of supporting loads up to 3 A. A floating gate driver powers the high-side N-channel MOSFET from an external boot-strap capacitor through the BST pin. The capacitor is charged when LX is pulled low through the rectifier, and the BST capacitor maintains sufficient voltage to enhance the high-side N-channel MOSFET during the on-time. An internal 12 Ω boost capacitor refresh MOSFET allows reliable power-up regardless of the output voltage level. The SKY87608 supports an adjustable output voltage using an external resistive voltage divider, allowing the output to be set to any voltage between 12% and 80% of the input voltage. The SKY87608 switches at 450 kHz. Current Limit Protection The SKY87608 includes protection for overload and short-circuit conditions by limiting the peak inductor current. During the “on” time, the controller monitors the current through the high-side MOSFET. If the current exceeds the peak current-limit threshold (5 A, typical), the controller immediately turns off the high-side MOSFET. The soft-start is discharged/reset if any of the following occurs: the regulator is disabled (EN pulled low), the input voltage drops below the UVLO threshold, or thermal shutdown is activated. Thermal Shutdown The SKY87608 includes thermal protection that disables the regulator when the die temperature reaches 160 °C. The thermal shutdown resets the soft-start circuit and automatically restarts when the temperature drops below 145 °C. Application Information To ensure that the maximum possible performance is obtained from the SKY87608, please refer to the following application recommendations for component selection. Adjustable Output Resistor Selection The output voltage (VOUT) may be set from 0.9 V to 80% of VIN. The resistive feedback voltage divider sets the output voltage according to the following relationship: Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 9 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER RFB1 is rounded to the nearest 1% resistor value. RFB2 is typically selected to be between 10 kΩ and 200 kΩ. The lower resistance improves noise immunity, but results in higher feedback current and reduced efficiency, as shown in Figure 26. For other output voltages, the inductance can be calculated based on the internal slope compensation requirement and equal to: Manufacturer’s specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the saturation characteristics. The inductor should not show any appreciable saturation under normal load conditions. The saturation current is a very important parameter for inductor selection. It must be more than the sum of DC current and maximum peak current through the inductor, and the adequate margin is important for safe application. The maximum peak current is given by the following equation: Figure 26. FB Resistor Divider Table 5 shows the divider resistor value for different output voltages. Table 5. Resistor Selection for Different Output Voltages Output Voltage (V) RFB1 (kΩ) (RFB2 = 20 kΩ) 1.5 13.3 3.3 53.6 5.0 91 8.0 158 10 200 12 249 15 316 18 383 20 422 Where L is the inductance and f is the operation frequency. Some inductors that meet the peak and average current ratings requirements still result in excessive losses due to a high Direct Current Resistance (DCR). Always consider the losses associated with the DCR and their effect on the total regulator efficiency when selecting an inductor. Table 6 shows the recommended inductor examples for different output voltages. Input Capacitor Typically, the input impedance is so low (or has other input capacitors distributed throughout the system) that a single 10 μF X7R or X5R ceramic capacitor located near the SKY87608 is sufficient. However, additional input capacitance may be necessary depending on the impedance of the input supply. To estimate the required input capacitance requirement, determine the acceptable input ripple level (VPP) and solve for CIN: Inductor Selection The step-down converter uses peak current mode control with slope compensation to maintain stability for duty cycles greater than 50%. The output inductor value must be selected to make the inductor current down slope to meet the internal slope compensation requirements. The internal slope compensation is designed to be 75% of the inductor current down slope of 5 V output with 6.8 μH inductor. Always examine the ceramic capacitor DC voltage coefficient characteristics when evaluating ceramic bypass capacitors. In addition to the capacitance requirement, the RMS current rating of the input capacitor must be able to support the pulsed current drawn by the step-down regulator. The input RMS current requirement may be determined by: Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Table 6. Inductor Selection for Different Output Voltages VOUT (V) 2.5 1.5 3.3 5 10 12 15 18 20 Saturation Current (A) DCR (mΩ) CDRH8D38NP-2R5N 5.5 17.5 744777002 6.5 DR73-2R2-R CDRH105RNP-4R7N CDRH10D68NP-4R7N Inductance (µH) 2.2 4.7 6.8 15 18 22 27 27 Part Number Dimension(mm) L×W×H Manufacturer 8.3×8.3×4 Sumida 20 7.3×7.3×4.5 Wurth Elektronik 5.52 16.5 7.9×7.9×3.8 Coil Tronics 6.4 12.3 10.5×10.3×5.1 6.6 9.8 10.5×10.5×7.1 7447715004 6.3 16 12×12×4.5 CDRH105RNP-6R8N 5.4 18 10.5×10.3×5.1 CDRH124NP-6R8M 4.9 23 12.3×12.3×4.5 7447715006 4.7 25 12×12×4.5 CDRH127NP-15M 4.5 27 12.3×12.3×8 CDRH127/LDHF-150M 5.65 26,4 12.3×12.3×8 744771115 4.55 30 DR125-150-R 5.69 29.8 Sumida Wurth Elektronik Sumida Wurth Elektronik Sumida 12×12×6 Wurth Elektronik 13×13×6.3 Coil Tronics CDRH127/LDHF-180M 5.1 28 12.3×12.3×8 Sumida 744771118 4.3 34 12×12×6 Wurth Elektronik DR125-180-R 5.32 37.7 13×13×6.3 Coil Tronics CDRH127/LDHF-220M 4.7 36.4 12.3×12.3×8 Sumida 744770122 5.0 43 12×12×8 Wurth Elektronik DR125-220-R 4.71 39.6 13×13×6.3 Coil Tronics CDRH127/LDHF-270M 4.2 41.6 12.3×12.3×8 Sumida 744770127 3.8 46 12×12×8 7447709270 5.8 40 12×12×10 CDRH127/LDHF-270M 4.2 41.6 744770127 3.8 46 12×12×8 7447709270 5.8 40 12×12×10 The term D × (1 – D) appears in both the input ripple voltage and input capacitor RMS current equations, so the maximum occurs when VOUT = 0.5 × VIN (50% duty cycle). This results in a set of “worst case” capacitance and RMS current design requirements: The input capacitor provides a low impedance loop for the pulsed current drawn by the SKY87608. Low Equivalent Series Resistance/Equivalent Series Inductance (ESR/ESL) X7R and X5R ceramic capacitors are ideal for this function. To minimize the stray inductance, the capacitor should be placed as closely as possible to the high-side MOSFET. This keeps the high 12.3×12.3×8 Wurth Elektronik Sumida Wurth Elektronik frequency content of the input current localized, minimizing EMI and input voltage ripple. The proper placement of the input capacitor can be seen in the Evaluation Board layout (see the "Layout Considerations" section of this Data Sheet). A laboratory test set-up typically consists of two long wires running from the bench power supply to the Evaluation Board input voltage pins. The inductance of these wires, along with the low-ESR ceramic input capacitor, can create a high-Q network that may affect the regulator’s performance. This problem often becomes apparent in the form of excessive ringing in the output voltage during load transients. Errors in the loop phase and gain measurements can also result. Since the inductance of a short PCB trace feeding the input voltage is significantly lower than the power leads from the bench power supply, most applications do not exhibit this problem. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 11 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER In applications where the lead inductance of the input power source cannot be reduced to a level that does not affect the regulator performance, a high-ESR tantalum or aluminum electrolytic should be placed in parallel with the low ESR/ESL ceramic capacitor. This reduces the input impedance and dampens the high-Q network, stabilizing the input supply. Output Capacitor The output capacitor impacts stability, limits the output ripple voltage, and maintains the output voltage during large load transitions. The SKY87608 is designed to work with any type of output capacitor since the controller features externally adjustable compensation (see the "Stability Considerations" and "Compensation Component Selection" sections of this Data Sheet). The output ripple voltage magnitude is determined by the output capacitor's ability to filter the inductor ripple current. The ripple voltage has two components, capacitive and ESR induced ripple voltage: The capacitive ripple and ESR ripple are phase shifted from each other, but depending on the type of output capacitor chemistry, one of them typically dominates. After a load step occurs, the output capacitor must support the difference between the load requirement and inductor current. Once the average inductor current increases to the DC load level, the output voltage recovers. Therefore, based on limitations in the ability to discharge the inductor, a minimum output voltage deviation may be determined by the following equation: Where, VSOAR is the output voltage overshoot and undershoot deviation. Bandwidth and gain limitations (depending on output capacitor and compensation component selection) may result in larger output voltage deviations. The ceramic output capacitor provides low ESR and low ESL, resulting in low output ripple dominated by the capacitive ripple voltage (ΔVOUT(CAP)). However, due to the lower capacitance value, the load transient response is significantly worse. Therefore, ceramic output capacitors are generally recommended only for designs with soft load transients (slow di/dt and/or small load steps). Tantalum and electrolytic capacitors provide a high-capacitance, low-cost solution. The bulk capacitance provides minimal output voltage drop/soar after load transients occur. Stability Considerations The SKY87608 uses a current-mode architecture, which relies on the output capacitor and a series resistor-capacitor network on the COMP pin for stability. COMP is the output of the transconductance error amplifier, so the RC network creates a pole-zero pair used to control the gain and bandwidth of the control loop. The DC loop gain (ADC) is set by the voltage gain of the internal transconductance amplifier (AEA = gM(EA) × ROUT = 3000 V/V), the compensation gain (ACC = 1 V/V), and the current-sense gain (ACS = 1 V/V): Where VFB is the 0.9 V feedback voltage, VOUT is the output voltage determined by the feedback resistors, RDS(ON) is the “on” resistance of the high-side N-channel MOSFET, and RLOAD is the output load resistance (RLOAD = VOUT /IOUT). Since the output impedance is a function of the load current and output voltage, the equation may be rewritten independent of the VOUT term: Additionally, the high-side “on” resistance RDS(ON) is inversely proportional to the maximum output current (IOUT) due to the peak current limit. This effectively limits the typical value of ADC to a value of 360 V/V (51 dB). The control loop has two dominant poles: one created by the output capacitor (COUT) and load resistance, and the other formed by the total compensation capacitance (CCC1 + CCC2) and the error amplifier transconductance (gM(EA) = 570 μA/V): However, the system also has two zeros in the control loop: one created by the series compensation resistor (RCOMP) and capacitor (CCC1), and the other formed by the output capacitor and its parasitic series resistance (ESR): Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER The ESR zero is highly dependent on the type of output capacitors being used (ceramic vs tantalum), and may not occur before crossover. If the ESR zero occurs low enough, the compensation zero formed by RCOMP may be placed at crossover to avoid stability problems. However, if both zeros are required below crossover, a third pole is needed to maintain stability. This third pole can be added by including another compensation capacitor (CCC2 in Figure 1) in parallel with the main series RC network: • RSEN is the high side current sensing resistor, RSEN = RDS(HS) in this case. There is already a 90° phase shift at very low frequencies, ωP1. Compensating the 2nd pole ωP2 with 1st zero ωZ1, the unity gain frequency can be simplified as: Set the unity gain frequency far away from the switching frequency to avoid any switching noise in the voltage loop, fT = fSW/20. If CCC2 << CCC1, the third pole is simplified to: To safely avoid the Nyquist pole (half the switching frequency), the crossover frequency should occur between 1/20th and 1/5th of the switching frequency. Lower crossover frequencies result in slower transient response speed, while higher crossover frequencies could result in instability, as shown in Figure 27. The ESR zero ωZ2 is used to cancel the high frequency pole ωP3. gm = 570 μA/V, gm × ROUT(EA) = 3000 V/V, RSEN = 100 mΩ, COUT = 22 μF, and RESR = 10 mΩ. For VOUT = 3.3 V, RCOMP = 2 kΩ, CCC1= 10 nF, and CCC2 = 100 pF. For VOUT = 5 V, RCOMP = 3 kΩ, CCC1= 10 nF, and CCC2 = 56 pF. For VOUT = 15 V, RCOMP = 9.1 kΩ, CCC1= 10 nF, and CCC2 = 22 pF. Table 7 gives the recommended compensation value for different output voltages. Table 7. Recommended Compensation Values VOUT (V) RCOMP (kΩ) CCC1 (nf) CCC2 (pf) 1.5 1.0 10 270 3.3 2 10 100 5 3 10 56 10 6.2 10 33 12 7.5 10 33 15 9.1 10 22 Compensation Component Selection 18 10 10 22 This is peak current mode control. An R-C series network (or type II) compensation is applied at the transconductance amplifier output (COMP). 20 12 10 22 Figure 27. Compensation Components • ROUT(EA) is the output impedance of the transconductance error amplifier. • N is the scaling factor of output current, ISEN = IOUT/N (N = 1 in this case). The type of output capacitor determines how the compensation components should be selected. With large tantalum and electrolytic capacitors, the output capacitor pole dominates the control loop design. Alternatively, small low-ESR ceramic capacitors rely on the compensation capacitor to generate the dominant pole. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 13 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Bootstrap Capacitor Selection To fully turn on the high side N-channel MOSFET, a bootstrap capacitor is connected between the BST pin and the LX pin. During the off time, the switching node is pulled to ground and the bootstrap capacitor charges up to approximately 5 V through an internal diode (see Figure 25). The bootstrap capacitor should be a 22 nF to 100 nF ceramic capacitor with a 10 V or greater voltage rating. Diode Selection To achieve maximum efficiency, a low-VF Schottky diode is recommended. Where ΔIL is the peak-to-peak value of inductor current. Select a diode with a DC rated current equal to the current RMS of the diode with an adequate margin for safe use. Table 8 lists a few recommended Schottky diodes. Thermal Calculations There are three types of losses associated with the SKY87608 step-down converter: switching losses, conduction losses, and quiescent current losses. The conduction losses are associated with the RDS(ON) characteristics of the internal high-side MOSFET. The switching losses are dominated by the gate charge and parasitic capacitance of the high-side MOSFET. Under full load conditions, the total power loss within the SKY87608 may be estimated by: where IQ is the step-down converter quiescent current, and tSW is the turn-on/off time of the MOSFET used to estimate the full load step-down converter switching losses. Since on time, quiescent current, and switching losses all vary with input voltage, the total power losses within the SKY87608 should be investigated over the complete input voltage range. The maximum junction temperature can be derived from the θJA for the SOP-8L-EP package, which is 41 °C/W. Layout Considerations The following guidelines should be used to help ensure a proper layout. 1. Connect the input capacitor as close as possible to the drain of the high-side N-channel MOSFET and the anode of the Schottky diode (and/or source of the low-side N-channel MOSFET). Keep this loop compact to reduce the switching noise. 2. Connect COUT and L1 as close as possible. The connection of L1 to the LX pin should be as short as possible and made at the source of the high-side N-channel MOSFET for current-sense accuracy. 3. Separate the feedback trace or FB pin from any power trace and connect as close as possible to the load point. Sensing along a high-current load trace degrades DC load regulation. 4. Minimize the resistance of the trace from the load return to PGND. This helps to minimize any error in DC regulation due to differences in the potential of the internal signal ground and the power ground. 5. Connect PGND to the exposed pad to enhance thermal impedance. Evaluation Board Description The SKY87608 Evaluation Board schematic diagram is provided in Figure 28. The PCB layer detail is shown in Figures 29 and 30. Component values for the SKY87608 Evaluation Board are listed in Table 9. Package Information Package dimensions and tape & reel dimensions are shown in Figures 31 and 32. Table 8. SKY87608 Schottky Diode Selection VR (V) VF (V) IF (A) Package Manufacturer B340A Part Number 40 0.5 @ 3 A 3 SMA VISHAY SS34 40 0.46 @ 3 A 3 SMC Fairchild MBRS540 40 0.5 @ 5 A 5 SMC ON CMSH5-40 40 0.55 @ 5 A 5 SMC Central Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Figure 28: SKY87608 Standard Application Circuit Schematic Figure 29: SKY87608 Evaluation Board Top Side Layout Figure 30: SKY87608 Evaluation Board Bottom Side Layout Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 15 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Table 9. SKY87608 Standard Application Circuit Bill of Materials (BOM) Component Part Number Description Manufacturer U1 SKY87608-11-577LF Step-down converter Murata C1 GRM188R71C103K Capacitor, ceramic, 10 nF, 0603 X7R, 16 V, 10% Murata C2 GRM1885C1H560J Capacitor, ceramic, 56 pF, 0603 C0G, 50 V, 5% Murata C5,C8 GRM188R61H105KAALD Capacitor, ceramic, 1 µF, 0603 X5R, 50 V, 10% Murata C6, C7, C10, C11 GRM32ER7YA106K Capacitor, ceramic, 10 µF, 1210 X7R, 35 V, 10% Murata CBST GRM188R71C104K Capacitor, ceramic, 0.1 µF, 0603 X7R, 16 V, 10% Murata C12 Not populated CFF R1 RC0603FR-073KL Resistor,3 kΩ, 1/10 W, 1%, 0603 SMD Yageo R4 RC0603FR-0791KL Resistor, 91 kΩ, 1/10 W, 1%, 0603 SMD Yageo R5 RC0603FR-0720KL Resistor, 20 kΩ, 1/10 W, 1%, 0603 SMD Yageo R6 RC0603FR-07100KL Resistor, 100 kΩ, 1/10 W, 1%, 0603 SMD Yageo D1 B340A Diode, 40 V, 3 A, SMA Vishay L1 7447715006 Inductor, 6.8 µH, 4.7 A Wurth Elektronik Figure 31. SKY87608 8-pin SOP-8L-EP Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 16 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Figure 32. SKY87608 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201860B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 17, 2013 17 PRELIMINARY DATA SHEET • SKY87608 28V, 3A NON-SYNCHRONOUS STEP-DOWN CONVERTER Ordering Information Model Name SKY87608 Step Down DC-DC Converter Manufacturing Part Number (Note 1) SKY87608-11-577LF Evaluation Board Part Number SKY87608-11-577LF-EVB Note 1: Sample stock is generally held on the part number listed in BOLD. Copyright © 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 18 May 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201860B