DATA SHEET SKY13524-639LF: 0.7 to 3.0 GHz High Isolation SP4T Switch Applications CDMA/WCDMA/TD-SCDMA/LTE single-ended filter switching RF1 Features RF2 Broadband frequency range: 0.7 to 3.0 GHz High isolation: 47 dB @ 2.0 GHz (typical) RFC RF3 Small QFN (14-pin, 1.6 x 1.6 mm) package (MSL1, 260 C per JEDEC J-STD-020) Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. V2 V1 VDD Logic and Supply Y2307 RF4 Figure 1. SKY13524-639LF Block Diagram Description The SKY13524-639LF is a single-pole, four-throw (SP4T) switch used for single-ended filter switching in cellular applications. The SKY13524-639LF maintains low insertion loss and high isolation for all switching paths. Depending on the logic voltage level applied to the control pins (V1 and V2), the RFC pin is connected to one of four switched RF outputs (RF1 to RF4) using a low insertion loss path, while the paths between the RFC pin and the other RF pins are in a high isolation state. The SKY13524-639LF is manufactured in a compact, 14-pin 1.6 x 1.6 mm, Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202801C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2, 2015 1 RF1 GND RF2 DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH 14 13 12 GND RFC 2 10 V1 VDD 3 9 V2 GND 4 8 N/C 5 6 7 RF3 11 GND 1 RF4 GND S3403 Figure 2. SKY13524-639LF Pinout – 14-Pin QFN (Top View) Table 1. SKY13524-639LF Signal Descriptions (Note 1) Pin Name Description Pin Name Description 1 GND Ground 8 N/C Not connected 2 RFC Antenna port. No DC blocking capacitor required. 9 V2 Control voltage 2 3 VDD DC power supply 10 V1 Control voltage 1 4 GND Ground 11 GND Ground 5 RF4 RF input/output port 4. DC blocking capacitor required. 12 RF2 RF input/output port 2. DC blocking capacitor required. 6 GND Ground 13 GND Ground 7 RF3 RF input/output port 3. DC blocking capacitor required. 14 RF1 RF input/output port 1. DC blocking capacitor required. Note 1: Bottom ground paddles must be connected to ground. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 September 2, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202801C DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH Functional Description Electrical and Mechanical Specifications The SKY13524-639LF includes an internal decoder and internal blocking capacitors on the RF common ports. External DC blocking capacitors are required on the RF1, RF2, RF3, and RF4 ports for proper operation. DC decoupling capacitors may be added on the VDD and control lines if necessary. The absolute maximum ratings of the SKY13524-639LF are provided in Table 2. Electrical specifications are provided in Table 3. The state of the SKY13524-639LF is determined by the logic shown in Table 4. Switching is controlled by two control voltage inputs, V1 and V2. Depending on the logic voltage level applied to the control pins, the antenna pin is connected to one of four switched RF outputs. Table 2. SKY13524-639LF Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Supply voltage VDD Control voltage (V1, V2) VCTL RF input power PIN Operating temperature TOP –30 Storage temperature TSTG –55 –0.5 Maximum Units 3.7 V +3.3 V +26 dBm +90 C +150 C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202801C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2, 2015 3 DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH Table 3. SKY13524-639LF General Electrical Specifications (Note 1) (VDD = 3.3 V, V1 = V2 = High = 1.8 V, PIN = 0 dBm, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Test Condition (Note 2) Symbol Min Typical Max Units 3.3 V 5 10 μA 1.80 3.30 0.45 V V 5 μA 0.9 1.0 1.05 dB dB dB DC Specifications Supply voltage VDD 2.5 Supply current IDD Control voltage: High Low VCTL_H VCTL_L Control current ICTL V1 = V2 = 1.8 V, VDD = 3.3 V Insertion loss (RFC pin to RF1/2/3/4 pins) IL 704 to 960 MHz 1710 to 2170 MHz 2300 to 2690 MHz Isolation (RFC pin to RF1/2/3/4 pins) Iso 704 to 960 MHz 1710 to 2170 MHz 2300 to 2690 MHz Voltage standing wave ratio, all ports VSWR 0.7 to 3.0 GHz, referenced to 50 Ω VDD = 3.3 V 1.35 0 RF Specifications 0.1 dB input compression point (RFC pin to RF1/2/3/4 pins) IP0.1dB Third order input intercept point IIP3 0.7 0.8 0.85 50 49 48 dB dB dB 1.4 – +32 dBm 0.7 to 3.0 GHz, all RF ports, fo = 0.8 to 3.0 GHz, Δf = 1 MHz, PIN = +20 dBm/tone +56 dBm Measured from 50% of final VDD supply voltage to final RF power ±1 dB 400 550 ηs Measured from 50% of final VCTRL voltage to final RF power ±1 dB 500 650 ηs 47 46 45 0.7 to 3.0 GHz Turn-on/turn-off time Switching speed Table 4. SKY13524-639LF Control Logic Note: VDD (Pin 3) V1 (Pin 10) V2 (Pin 9) Insertion Loss Path 1 1 0 RFC to RF1 1 0 0 RFC to RF2 1 0 1 RFC to RF3 1 1 1 RFC to RF4 “1” = 1.8 V; “0” = 0 V. Any state other than that described in this Table places the switch into an undefined state. An undefined state will not damage the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 September 2, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202801C DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH Evaluation Board Description Package and Handling Information The SKY13524-639LF Evaluation Board is used to test the performance of the SKY13524-639LF SP4T Switch. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY13524-639LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Package Dimensions The PCB layout footprint for the SKY13524-639LF is provided in Figure 5. Typical case markings are shown in Figure 6. Package dimensions for the 14-pin QFN are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. RF1 GND C4 47 pF 14 RF1 1 13 GND RF2 12 C5 47 pF RF2 GND GND 11 GND GND 2 RFC 3 C1 10 nF RFC V1 VDD V2 10 DCH1 Header 4 GND 3 V1 2 V2 9 1 VDD 4 GND RF4 C2 47 pF GND N/C RF4 GND RF3 5 6 7 8 RF3 C3 47 pF GND ts185 Figure 3. SKY13524-639LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202801C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2, 2015 5 DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH RFC RF4 RF1 RF3 RF2 C1 = 10 nF C2, C3, C4, C5 = 47 pF VDD V2 V1 GND ts186 Figure 4. SKY13524-639LF Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 September 2, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202801C DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH 14X 0.200 Pin 14 Pin 1 Indicator 0.22 × 0.22 4X 0.180 × 0.075 4X 0.152 × 0.064 Exposed Soldering Area Pin 1 0.400 Pitch 3X 1.944 2X 0.370 14X 0.200 4X 0.345 10X 0.400 2X 0.370 4X 1.944 Y2308 All dimensions are in millimeters. Figure 5. SKY13524-639LF PCB Layout Footprint (Top View) Pin 1 Indicator Part number SKY 3524 ts188 Figure 6. Typical Part Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202801C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2, 2015 7 DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH Seating Plane C 1.60 A 0.40 Pitch Exposed Pad See Detail A B Pin 1 Indicator 0.02 +0.03 –0.02 12 See Detail B 1.60 14 11 R0.22 Pin 1 Indicator 1 0.74 +0.1 –0.15 20° 8 0.05 C 2X 2X 0.45 +0.05 –0.04 0.10 C 0.05 C Top View 4 7 See Detail C 14X 0.200 Min 14X 3 0.08 C 0.10 0.20 5 0.74 +0.1 –0.15 Side View Bottom View 0.163 ± 0.05 0.150 Typ R0.05 Typ. 0.150 Typ 0.18 ± 0.05 0.2 ± 0.05 R0.05 Typ 0.18 ± 0.05 0.150 Typ 0.2 ± 0.05 R0.05 Typ 5 0.18 ± 0.05 0.10 M C A B 0.05 M C Detail A Scale: 100X 1X This Rotation 1X Rotated 180° 0.2 ± 0.05 R0.05 Typ Detail B Scale: 100X 1X This Rotation 1X Rotated 180° 1X Mirrored 1X Mirrored 180° Notes: 1. 2. 3. 4. 5. All measurements are in millimeters. Dimensions and tolerances according to ASME Y14.5M-1994. Coplanarity applies to the terminals and all other bottom surface metallization. Plating requirement per source control drawing (SCD) 2504. Dimension applies to metallized terminal. If the terminal has a radius on its end, the width dimension should not be measured in that radius area. 5 0.10 M C A B 0.18 ± 0.05 0.05 M C Detail C Scale: 100X 1X This Rotation 1X Rotated 180° 1X Rotated 90° CW 1X Rotated 90° CCW Figure 7. SKY13524-639LF 14-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 September 2, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202801C S3402 DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH ϕ1.50± 0.10 4.00 ± 0.10 2.00 ± 0.05 0.20 ± 0.02 (T) 1.75 ± 0.10 Pin 1 1.78 ± 0.05 (Bo) B A A 8.00 +0.30/–0.10 3.50 ± 0.05 5o Max B 0.69 ± 0.05 (Ko) ϕ0.50± 0.05 B 5o Max 1.78 ± 0.05 (Ao) A Notes: 1. Carrier tape: black conductive polycarbonate. 2. Cover tape material: transparent conductive PSA. 3. Cover tape size: 5.4 mm width. 4. All measurements are in millimeters. 5. ESD surface resistivity is ≤1 x 108 Ohms/square per EIA, JEDEC tape and reel specification. 6. Pin 1 orientation is in lower left corner for SOT-666 packages. Pin 1 orientation is in upper left corner for 1.5 x 1.5 mm and 1.6 x 1.6 mm MLPD, QFN, and DFN packages. S1382 Figure 8. SKY13524-639LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202801C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2, 2015 9 DATA SHEET • SKY13524-639LF: HIGH ISOLATION SP4T SWITCH Ordering Information Model Name SKY13524-639LF: 0.7 to 3.0 GHz High Isolation SP4T Switch Manufacturing Part Number SKY13524-639LF Evaluation Board Part Number SKY13524-639LF-EVB Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 September 2, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202801C