PRODUCT SUMMARY SKY81292: 1.8 A Single or Dual Flash LED Driver with I2C Control Interface Applications Description • LED photo flash with Movie/Torch modes The SKY81292 is a high-efficiency, 1.8 A high-current boost converter with a programmable constant current. The device is intended for LED photo flash applications in all single-cell Li-ion powered portable products. • Camera enabled mobile devices • Cell phones/smartphones • Digital still cameras • Multimedia mobile phones Features • Input voltage range: 2.5 V to 5.5 V • Supports single and dual flash LEDs • Up to 1.8 A regulated output current • Up to 90% efficiency • Switching frequency: 2 MHz • True load disconnect • Soft-start and input current limit • Separate flash enable • Industry standard I2C programming: − Flash and Movie mode current − Battery current limit − Input voltage monitor with programmable thresholds − Programmable safety timer − Fault readback • Fault protection: − Flash timer − Over-voltage (open LED, open circuit) − Short circuit − Over-temperature protection − NTC resistor flash LED temperature sense − Flash mode input voltage monitor − Open drain fault flag output • Independent current source for LED indicator lamp • Small WLCSP (16-bump, 2 mm x 2 mm) package (MSL1, 260 °C per JEDEC J-STD-020) package The SKY81292 maintains the flash LED output current using a DCDC step-up converter with a bypass function to maximize efficiency when under all load conditions. For single flash LED applications, the flash current can be programmed up to 1.8 A. For dual flash LED applications, the flash current can be programmed up to 900 mA. This provides a direct flash LED cathode connection to the ground plane that helps heat dissipation. The high frequency 2 MHz DC-DC boost switching frequency allows the use of a small external inductor and output capacitor, which makes the SKY81292 ideally suited for small batterypowered applications. A start-up control circuit automatically senses the flash LED forward voltage at any programmed output current setting and determines the most efficient operation mode. An industry standard I2C digital interface is used to program the SKY81292 LED flash and movie modes. Device operations are fully configurable; movie and flash current level, current limits, and fault reporting. Also included is a separate flash enable input to initiate the flash operation and a flash inhibit input to reduce the flash current to movie-mode levels during high battery demand conditions. An additional low-level programmable current source output is provided to drive an LED indicator lamp. The integrated thermal management system protects the device in the event of an output short-circuit condition. An NTC thermistor function protects the external flash LEDs from thermal damage. Fault status may be read using the I2C interface after the system is alerted by an open drain fault flag. Built-in soft-start circuitry prevents excessive in-rush current during start-up. The shutdown feature reduces quiescent current to less than 1.0 μA. The SKY81292 is provided in a small, 16-bump, 2 mm x 2 mm Wafer Level Chip Scale Package (WLCSP). The pin configuration and package are shown in Figure 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202542A • Skyworks Proprietary Information • Products and Product Information Are Subject To Change Without Notice • November 27, 2012 1 PRODUCT SUMMARY • SKY81292 FLASH LED DRIVER WITH I2C CONTROL INTERFACE Figure 1. SKY81292 Pinout – 16-Bump WLCSP Package (Top View) Ordering Information Model Name SKY81292 Flash LED Driver with I2C Control Interface Manufacturing Part Number SKY81292-11-001 Evaluation Board Part Number TW21-D260 Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. 2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com November 27, 2012 • Skyworks Proprietary Information • Products and Product Information Are Subject To Change Without Notice • 202542A