S-19400/19401 Series
www.sii-ic.com
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION
WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
© SII Semiconductor Corporation, 2014-2016
The S-19400/19401 Series is a watchdog timer developed using CMOS technology, which can operate with low current
consumption of 3.8 μA typ. The reset function and the low voltage detection function are available.
Caution
This product can be used in vehicle equipment and in-vehicle equipment. Before using the product in
the purpose, contact to SII Semiconductor Corporation is indispensable.
Features
• Detection voltage:
• Detection voltage accuracy:
• Input voltage:
• Hysteresis width:
• Current consumption:
• Reset time-out period:
• Watchdog operation is switchable:
• Watchdog operation voltage range:
• Watchdog mode switching function*1:
• Watchdog input edge is selectable:
• Product type is selectable:
• Operation temperature range:
• Lead-free (Sn 100%), halogen-free
• AEC-Q100 qualified*2:
*1.
*2.
2.0 V to 5.0 V, selectable in 0.1 V step
±2.0%
VDD = 0.9 V to 6.0 V
5% typ.
3.8 μA typ.
14.5 ms typ. (CPOR = 2200 pF)
Enable, Disable
2.5 V to 6.0 V
Time-out mode, window mode
Rising edge, falling edge, both rising and falling edges
S-19400 Series
___
________
(Product with W / T pin (Output: WDO pin))
S-19401 Series ___
_______
________
(Product without W / T pin (Output: RST pin, WDO pin))
Ta = −40°C to +125°C
TMSOP-8 package product
The S-19401 Series is fixed to the window mode.
HSNT-8(2030) package product is in the process of AEC-Q100.
Contact our sales office for details.
Applications
• For automotive use (engine, transmission, suspension, ABS, related-devices for EV / HEV / PHEV, etc.)
Packages
• TMSOP-8
• HSNT-8(2030)
1
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Block Diagrams
1.
____
S-19400 Series (Product with W / T pin)
CWDT
VDD
WEN
Noise
filter
WDI
Noise
filter
W/T
Noise
filter
WDT circuit
WDO
VSS
Voltage detection
circuit
Reference
voltage
circuit
CPOR
Figure 1
2.
____
S-19401 Series (Product without W / T pin)
CWDT
VDD
WEN
Noise
filter
WDI
Noise
filter
WDT circuit
RST
WDO
VSS
Reference
voltage
circuit
Voltage detection
circuit
CPOR
Figure 2
2
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
AEC-Q100 Qualified*1
TMSOP-8 package product of this IC supports AEC-Q100 for the operation temperature grade 1.
Contact our sales office for details of AEC-Q100 reliability specification.
*1.
HSNT-8(2030) package product is in the process of AEC-Q100.
Contact our sales office for details.
Product Name Structure
Users can select the product type, detection voltage, and package type for the S-19400/19401 Series. Refer to "1.
Product name" regarding the contents of product name, "2. Product type list" regarding the product types, "3.
Packages" regarding the package drawings.
1.
Product name
S-1940
x
x
xx
A -
xxxx
U
4
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
K8T2: TMSOP-8, Tape
A8T1: HSNT-8(2030), Tape
Operation temperature
A:
Ta = −40°C to +125°C
Detection voltage
20 to 50
(e.g., when the detection voltage is 2.0 V, it is expressed as 20.)
Product type 1*2
A to L
Product type 2*3
0, 1
*1.
*2.
*3.
Refer to the tape drawing.
Refer to "2. Product type list". ___
0: S-19400
Series (Product with W / T pin)
________
The WDO pin outputs the signals which are from the watchdog timer circuit and the voltage detection
circuit.
___
1: S-19401
Series (Product without W / T pin)
________
The WDO pin outputs the signals which are from the watchdog timer circuit and the voltage detection
circuit.
_______
The RST pin outputs the signal which is from the voltage detection circuit.
The watchdog mode is fixed to the window mode.
3
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
2.
Product type list
Product Type
A
B
C
D
E
F
G
H
I
J
K
L
3.
WEN Pin Logic
Active "H"
Active "H"
Active "H"
Active "L"
Active "L"
Active "L"
Active "H"
Active "H"
Active "H"
Active "L"
Active "L"
Active "L"
Table 1
Input Edge
Rising edge
Falling edge
Both rising and falling edges
Rising edge
Falling edge
Both rising and falling edges
Rising edge
Falling edge
Both rising and falling edges
Rising edge
Falling edge
Both rising and falling edges
Packages
Table 2
Package Name
TMSOP-8
HSNT-8(2030)
4
Output Pull-up Resistor
Available
Available
Available
Available
Available
Available
Unavailable
Unavailable
Unavailable
Unavailable
Unavailable
Unavailable
Package Drawing Codes
Dimension
Tape
Reel
Land
FM008-A-P-SD
PP008-A-P-SD
FM008-A-C-SD
PP008-A-C-SD
FM008-A-R-SD
PP008-A-R-SD
−
PP008-A-L-SD
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Pin Configurations
1.
TMSOP-8
Table 3
Top view
1
2
3
4
Pin No.
8
7
6
5
Figure 3
1
2
3
4
5
6
7
8
Table 4
Pin No.
1
2
3
4
5
6
7
8
___
S-19400 Series (Product with W / T pin)
Symbol
W / T*1
CPOR
CWDT
VSS
WEN
________
WDO
WDI
VDD
___
Description
Watchdog mode switching pin
Reset time-out period adjustment pin
Watchdog time adjustment pin
GND pin
Watchdog enable pin
Watchdog output pin
Watchdog input pin
Voltage input pin
___
S-19401 Series (Product without W / T pin)
Symbol
RST
CPOR
CWDT
VSS
WEN
________
WDO
WDI
VDD
_______
Description
Reset output pin
Reset time-out period adjustment pin
Watchdog time adjustment pin
GND pin
Watchdog enable pin
Watchdog output pin
Watchdog input pin
Voltage input pin
___
*1. W
/ T pin = "H": Time-out mode
___
W / T pin = "L": Window mode
5
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
2.
HSNT-8(2030)
Table 5
Top view
Pin No.
1
8
4
5
Bottom view
8
1
5
4
1
2
3
4
5
6
7
8
___
S-19400 Series (Product with W / T pin)
Symbol
W / T*2
CPOR
CWDT
VSS
WEN
________
WDO
WDI
VDD
___
Description
Watchdog mode switching pin
Reset time-out period adjustment pin
Watchdog time adjustment pin
GND pin
Watchdog enable pin
Watchdog output pin
Watchdog input pin
Voltage input pin
*1
Figure 4
Table 6
Pin No.
1
2
3
4
5
6
7
8
___
S-19401 Series (Product without W / T pin)
Symbol
RST
CPOR
CWDT
VSS
WEN
________
WDO
WDI
VDD
_______
Description
Reset output pin
Reset time-out period adjustment pin
Watchdog time adjustment pin
GND pin
Watchdog enable pin
Watchdog output pin
Watchdog input pin
Voltage input pin
*1. Connect the heat sink of backside at shadowed area to the board, and set electric potential open or GND.
However, do not use it as the function of electrode.
___
/ T pin = "H": Time-out mode
*2. W
___
W / T pin = "L": Window mode
6
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Pin Functions
Refer to " Operation" for details.
1.
____
W / T pin (S-19400 Series only)
This is a pin to switch the watchdog mode.
___
The S-19400
Series changes to the time-out mode when the W / T pin is "H", and changes to the window mode
___
when the W / T pin is "L". Switching the mode is prohibited during
the operation.
___
The constant current source (0.3 μA typ.) is connected to the W / T pin, and it is pulled down internally.
1. 1
___
Time-out mode (W / T pin = "H")
The S-19400 Series detects an abnormality when not
inputting an edge to the WDI pin during the watchdog
________
time-out period (tWDU). And then "L" is output from the WDO pin.
W/T
(S-19400 only)
"H"
tWDU
tRST
WDI
(Rising edge)
WDO
Figure 5
1. 2
Abnormality Detection in Time-out Mode
___
Window mode (W / T pin = "L")
When not inputting an edge to the WDI pin during tWDU, or when an edge is input to the WDI pin again within a
specific period of time (the discharge________
time due to an edge detection + 1 charge-discharge time (tWDL)) after
inputting an edge to the WDI pin, the WDO pin output changes from "H" to "L".
W/T
(S-19400 only)
"L"
WDI
(Rising edge)
WDO
tWDL
Figure 6
2.
tRST
tWDU
tRST
Abnormality Detection in Window Mode
________
RST pin (S-19401 Series only)
This is a reset output pin. It outputs "L" when_______
detecting a low voltage.
Be sure to connect a pull-up resistor to the RST pin in the product without an output pull-up resistor.
3. CPOR pin
This is a pin to connect an external capacitor in order to generate the reset time-out period (tRST).
The capacitor is charged and discharged by an internal constant current circuit, and the charge-discharge duration is
tRST.
tRST is calculated by using the following equation.
tRST = 6,500,000 × CPOR [F] + 0.0002
7
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
4. CWDT pin
This is a pin to connect an external capacitor in order to generate the watchdog time-out period (tWDU) and the
watchdog double pulse detection time (tWDL). The capacitor is charged and discharged by an internal constant
current circuit.
tWDU is calculated by using the following equation.
tWDU = 50,000,000 × CWDT [F] + 0.0011
Moreover, tWDL is calculated by using the following equation.
tWDU
tWDL = 32
5. WEN pin
This is a pin to switch Enable / Disable of the watchdog timer.
When the WEN pin logic is active "H", the watchdog timer becomes Enable if the input is "H", and the
charge-discharge operation is performed at the CWDT pin. In the active "H" product, the constant current source
(0.3 μA typ.) is connected to the WEN pin, and it is pulled down internally.
6.
_________
WDO pin
This pin combines the reset output and the watchdog
output.
________
Be sure to connect a pull-up resistor to the WDO pin in the product without an output pull-up resistor.
7. WDI pin
This is an input pin to receive a signal from the monitored object. By being input an edge at an appropriate timing, the
WDI pin confirms the normal operation of the monitored object.
The constant current source (0.3 μA typ.) is connected to the WDI pin, and it is pulled down internally.
8
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Absolute Maximum Ratings
Table 7
(Ta = −40°C to +125°C unless otherwise specified)
Absolute Maximum Rating
Unit
VDD pin voltage
VDD
V
VSS − 0.3 to VSS + 7.0
WDI pin voltage
VWDI
V
VSS − 0.3 to VDD + 0.3 ≤ VSS + 7.0
WEN
pin
voltage
V
−
0.3
to
V
+
0.3
≤
V
+
7.0
V
V
WEN
SS
DD
SS
___
Vw / T
W / T pin voltage
V
VSS − 0.3 to VDD + 0.3 ≤ VSS + 7.0
CPOR pin voltage
VCPOR
V
VSS − 0.3 to VDD + 0.3 ≤ VSS + 7.0
CWDT pin voltage
VCWDT
V
VSS − 0.3 to VDD + 0.3 ≤ VSS + 7.0
_______
A / B / C / D / E / F type
V
VSS − 0.3 to VDD + 0.3 ≤ VSS + 7.0
RST pin voltage
V RST
G / H / I / J / K / L type
V
VSS − 0.3 to VSS + 7.0
________
A / B / C / D / E / F type
VSS − 0.3 to VDD + 0.3 ≤ VSS + 7.0
V
VWDO
WDO pin voltage
G / H / I / J / K / L type
V
VSS − 0.3 to VSS + 7.0
Operation ambient temperature
Topr
−40 to +125
°C
Storage temperature
Tstg
−40 to +150
°C
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
Item
Symbol
___
_______
________
Thermal Resistance Value
Table 8
Item
Symbol
Condition
Board 1
Board 2
θja
Junction-to-ambient thermal resistance
Board 1
HSNT-8(2030)
Board 2
*1. Test environment: compliance with JEDEC STANDARD JESD51-2A
TMSOP-8
*1
Remark
Min.
−
−
−
−
Typ.
160
133
181
135
Max.
−
−
−
−
Unit
°C/W
°C/W
°C/W
°C/W
Refer to " Thermal Characteristics" for details of power dissipation and test board.
9
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Electrical Characteristics
Table 9 (1 / 2)
Item
Detection voltage*1
Hysteresis width
(WEN pin logic active "H" product, VDD = 5.0 V, Ta = −40°C to +125°C unless otherwise specified)
Test
Symbol
Condition
Min.
Typ.
Max.
Unit
Circuit
−VDET(S)
−VDET(S)
−VDET(S)
V
−
−VDET
1
× 0.98
× 1.02
−VDET
−VDET
−VDET
V
VHYS
−
1
× 0.03
× 0.05
× 0.07
Current consumption
during operation
Reset time-out period
ISS1
When watchdog timer operates
−
3.8
9.0
μA
2
tRST
CPOR = 2200 pF
8.7
14.5
20
ms
3
Watchdog time-out period
Watchdog double pulse
detection time
tWDU
CWDT = 470 pF
15
24.6
34
ms
3
tWDL
CWDT = 470 pF
461
769
1077
μs
4
Reset output voltage "H"
VROH
VDD − 1.0
−
−
V
5
Reset output voltage "L"
VROL
−
−
0.4
V
6
−
−0.85
−0.4
μA
7
0.48
1.1
−
mA
8
0.8
1.6
−
mA
8
1.0
2.6
−
mA
8
1.4
3.3
−
mA
8
−
−
0.096
μA
9
S-19401 Series A / B / C / D /
E / F type only
−
V RST = 0 V,
S-19401 Series A / B / C / D /
E / F type only
VDD = 1.5 V
VDS = 0.4 V,
VDD = 1.8 V
S-19401 Series
VDD = 2.5 V
only
VDD = 3.0 V
VDS = 6.0 V, VDD = 6.0 V,
S-19401 Series only
A / B / C / D / E / F type only
_______
Reset output pull-up current
Reset output current
IRUP
IROUT
Reset output leakage current IRLEAK
Watchdog output voltage "H" VWOH
Watchdog output voltage "L"
Watchdog output
pull-up current
Watchdog output current
−
VWOL
VDD − 1.0
−
−
V
10
−
−
0.4
V
11
VWDO = 0 V,
A / B / C / D / E / F type only
VDD = 1.5 V
−
−0.85
−0.4
μA
12
0.48
1.1
−
mA
13
VDD = 1.8 V
0.8
1.6
−
mA
13
VDD = 2.5 V
1.0
2.6
−
mA
13
VDD = 3.0 V
1.4
3.3
−
mA
13
−
−
0.096
μA
14
________
IWUP
IWOUT
VDS = 0.4 V
Watchdog output leakage
current
Input pin voltage 1 "H"
VSH1
WEN pin
0.7 × VDD
−
−
V
15
Input pin voltage 1 "L"
VSL1
−
0.3 × VDD
V
15
Input pin voltage 2 "H"
VSH2
−
−
V
15
Input pin voltage 2 "L"
VSL2
WEN
pin
−
___
W / T pin, S-19400 Series only 0.7 × VDD
___
W / T pin, S-19400 Series only
−
−
0.3 × VDD
V
15
Input pin voltage 3 "H"
VSH3
WDI pin
0.7 × VDD
−
−
V
15
Input pin voltage 3 "L"
VSL3
WDI pin
−
−
0.3 × VDD
V
15
10
IWLEAK
VDS = 6.0 V, VDD = 6.0 V
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Table 9 (2 / 2)
(WEN pin logic active "H" product, VDD = 5.0 V, Ta = −40°C to +125°C unless otherwise specified)
Test
Symbol
Condition
Min.
Typ.
Max.
Unit
Circuit
Item
Input pin current 1 "H"
ISH1
Input pin current 1 "L"
ISL1
Input pin current 2 "H"
ISH2
Input pin current 2 "L"
ISL2
Input pin current 3 "H"
ISH3
Input pin current 3 "L"
ISL3
−
0.3
1.0
μA
15
−0.1
−
0.1
μA
15
−0.1
−
0.1
μA
15
−
0.3
1.0
μA
15
−0.1
−
0.1
μA
15
−
0.3
1.0
μA
15
−0.1
−
0.1
μA
15
*2
thigh1
−
1.5
−
−
μs
15
*2
tlow1
−
1.5
−
−
μs
15
tWOUT
−
−
25
40
μs
3
Input pulse width "H"
Input pulse width "L"
A/B/C
/G/H/I
WEN pin,
type
VDD = 6.0 V,
D/E/F
Input pin voltage = 6.0 V
/J/K/L
type
WEN pin, VDD = 6.0 V,
Input
pin voltage = 0 V
___
W / T pin, S-19400 Series only,
VDD = 6.0 V, Input pin voltage = 6.0 V
___
W / T pin, S-19400 Series only,
VDD = 6.0 V, Input pin voltage = 0 V
WDI pin, VDD = 6.0 V,
Input pin voltage = 6.0 V
WDI pin, VDD = 6.0 V,
Input pin voltage = 0 V
Watchdog output delay time
Reset output delay time
tROUT
−
−
25
40
μs
3
Input setup time
tiset
−
1.0
−
−
μs
3
*1.
*2.
−VDET: Actual detection voltage, −VDET(S): Set detection voltage
The input pulse width "H" (thigh1) and the input pulse width "L" (tlow1) are defined as shown in Figure 7.
Inputs to the WEN pin and the WDI pin should be greater than or equal to the min. value specified in " Electrical
Characteristics".
thigh1
VSH1
VSH1
WEN
VSL1
VSL1
tlow1
thigh1
VSH3
WDI
VSH3
VSL3
VSL3
tlow1
Figure 7
11
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Test Circuits
A
VDD
VDD
CPOR
CWDT
CPOR
WDO
WDI
WEN
V
+
V
+
W/T
WDI
WEN
W/T
VSS
Figure 8
VSS
Test Circuit 1
Figure 9
Test Circuit 2
VDD
VDD
CPOR
CWDT
CPOR
WDO
WEN
V
+
W/T
WDI
WEN
+
VSS
Test Circuit 3
Figure 11
Test Circuit 4
VDD
VDD
CPOR
CWDT
CPOR
WDO
CWDT
WDI
WDO
WDI
WEN
RST
VSS
12
V
W/T
VSS
Figure 12
WDO
CWDT
WDI
Figure 10
WDO
CWDT
Test Circuit 5
WEN
V
+
RST
VSS
Figure 13
Test Circuit 6
V
+
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
VDD
VDD
CPOR
CPOR
WDO
CWDT
WDI
WDI
WEN
WEN
RST
A
VSS
Figure 14
WDO
CWDT
RST
VSS
Test Circuit 7
Figure 15
Test Circuit 8
VDD
VDD
CPOR
CPOR
CWDT
WDO
CWDT
WDO
WDI
WDI
WEN
RST
WEN
A
V
W/T
Test Circuit 9
Figure 17
Test Circuit 10
VDD
VDD
CPOR
CWDT
CPOR
WDO
CWDT
WDI
WEN
V
W/T
+
WDO
WDI
WEN
A
W/T
VSS
VSS
Figure 18
+
VSS
VSS
Figure 16
A
Test Circuit 11
Figure 19
Test Circuit 12
13
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
VDD
VDD
CPOR
CWDT
CPOR
WDO
A
CWDT
WDI
WDI
WEN
WEN
W/T
W/T
VSS
Figure 20
VSS
Test Circuit 13
Figure 21
VDD
CPOR
CWDT
A
WDO
WEN, WDI, W / T
VSS
Figure 22
14
WDO
Test Circuit 15
V
+
Test Circuit 14
A
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Operation
From power-on to reset release
The S-19400/19401 Series initiates the initialization if the VDD pin voltage exceeds the release voltage (+VDET).
The ________
charge-discharge operation
to the CPOR pin is initiated after the passage of the initialization time (tINIT), and
_______
the WDO pin output and the RST pin output change from "L" to "H" after the operation is performed 4 times.
VDD
+VDET
VCPU
CPOR
VCPL
WDO
Output "L" → "H"
RST
tINIT
(S-19401 only)
Output "L" → "H"
tRST
Remark VCPU: CPOR charge upper limit threshold (1.25 V typ.)
VCPL: CPOR charge lower limit threshold (0.20 V typ.)
Figure 23
tINIT changes according to the power supply rising time. Refer to Figure 24 for the relation between tINIT and the
power supply rising time.
0.1
Initialization time [s]
1.
0.01
0.001
0.0001
0.000001 0.00001 0.0001
0.001
0.01
0.1
Power supply rising time [s]
Figure 24
Power Supply Rising Time Dependency of Initialization Time
Power supply rising time
VDD
CPOR
Initialization time*1
*1.
The initialization time is the time period from when the VDD pin voltage reaches VDD / 2 to when CPOR rises.
Figure 25
Initialization Time
15
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
2.
From reset release to initiation of charge-discharge operation to CWDT pin
The charge-discharge operation to the CWDT pin differs depending on the status of the WEN pin at the reset release.
2. 1
When WEN pin is "H" at reset release (Active "H")
Since the watchdog timer is Enable, the S-19400/19401 Series initiates the charge-discharge operation to the
CWDT pin.
VDD
CPOR
CWDT
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 26
2. 2
WEN Pin = "H"
When WEN pin is "L" at reset release (Active "H")
Since the watchdog timer is Disable after the CPOR pin performs the charge-discharge operation 4 times, the
S-19400/19401 Series does not initiate the charge-discharge operation to the CWDT pin. If the input to the WEN
pin changes to "H" in this status, the S-19400/19401 Series initiates the charge-discharge operation to the CWDT
pin.
VDD
CPOR
CWDT
WEN
Charge-discharge operation is initiated
at WEN pin = "H"
(Active "H")
WDO
RST
(S-19401 only)
Figure 27
16
WEN Pin = "L" → "H"
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
3.
Watchdog time-out detection
The watchdog
timer detects a time-out after the charge-discharge operation to the CWDT pin is performed 32 times,
________
then the WDO pin output changes from "H" to "L".
VDD
1
2
3
4
CPOR
1
1
2
3
4
5
2
3
4
29 30 31 32
1
2
3
CWDT
WDI
"L"
WEN
(Active "H")
WDO
RST
tWDU
(S-19401 only)
tRST
Figure 28
4.
Internal counter reset due to edge detection
When the WDI pin detects an edge during the charge-discharge operation to the CWDT pin, the internal counter
which counts the number of times of the charge-discharge operation is reset. The CWDT pin initiates the discharge
operation when an edge is detected, and initiates the charge-discharge operation again after the discharge operation
is completed.
4. 1
Counter reset due to rising edge detection
(S-1940xAxxA, S-1940xDxxA, S-1940xGxxA, S-1940xJxxA)
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
1
2
3
4
30 31 32
1
CWDT
WDI
Counter reset due to rising edge detection
Time-out after counter reset
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 29
17
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
4. 2
Counter reset due to falling edge detection
(S-1940xBxxA, S-1940xExxA, S-1940xHxxA, S-1940xKxxA)
VDD
1
2
3
1
4
2
3
4
CPOR
1
2
4
3
1
2
3
4
30 31 32
1
CWDT
WDI
Counter reset due to falling edge detection
Time-out after counter reset
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 30
4. 3
Counter reset due to both rising and falling edges detection 1
(S-1940xCxxA, S-1940xFxxA, S-1940xIxxA, S-1940xLxxA)
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
1
2
1
2
30 31 32
1
CWDT
Counter reset due to
WDI
both rising and falling edges detection
Time-out after counter reset
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 31
18
2
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
4. 4
Counter reset due to both rising and falling edges detection 2
(S-1940xCxxA, S-1940xFxxA, S-1940xIxxA, S-1940xLxxA)
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
1
2
1
2
30 31 32
1
2
CWDT
Counter reset due to
WDI
both rising and falling edges detection
Time-out after counter reset
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 32
5.
WEN pin operation during charge-discharge operation to CWDT pin
When the WEN pin changes from "H" to "L" during the charge-discharge operation to the CWDT pin, the CWDT pin
performs the discharge operation. Moreover, the internal counter which counts the number of times of the
charge-discharge operation for the CWDT pin is also reset.
If the WEN pin changes to "H" again in this status, the CWDT pin initiates the charge-discharge operation.
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
1
2
31 32
1
2
CWDT
Watchdog timer restarts the operation at WEN pin = "H"
WEN
(Active "H")
Charge-discharge operation is stopped, counter reset
WDO
RST
(S-19401 only)
Figure 33
19
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
6.
Watchdog double pulse detection
If an edge is input to the WDI pin again within a specific period of time (the discharge time due to an edge detection +
1 charge-discharge
time (tWDL)) after inputting an edge to the WDI pin when the S-19400/19401 Series is the window
________
mode, the WDO pin output changes from "H" to "L".
When the watchdog timer________
becomes Disable due to a change of the WEN pin ("H" → "L" → "H") after inputting an
edge to the WDI pin, the WDO pin continues outputting "H" even if an edge is input to the WDI pin within the specific
period of time mentioned above.
6. 1
Double pulse detection due to rising edge detection
(S-1940xAxxA, S-1940xDxxA, S-1940xGxxA, S-1940xJxxA)
tWDL
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
1
2
3
4
5
6
7
8
9 10
1
2
3
4
5
6
7
8
9 10
CWDT
WDI
W / T "L"
(S-19400 only)
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 34
6. 2
Double pulse detection due to falling edge detection
(S-1940xBxxA, S-1940xExxA, S-1940xHxxA, S-1940xKxxA)
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
CWDT
Counter reset at the 1st edge
WDI
Output "H" → "L" at the 2nd edge
W / T "L"
(S-19400 only)
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 35
20
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
6. 3
Double pulse detection due to both rising and falling edges detection
(S-1940xCxxA, S-1940xFxxA, S-1940xIxxA, S-1940xLxxA)
The double pulse is detected only when edges are input in order of rising and falling.
6. 3. 1
When edges are input to WDI pin in order of rising and falling
VDD
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
1
2
3
4
5
6
7
8
9 10 11
1
2
3
CWDT
Counter reset at the1st edge
Output "H" → "L" at the 2nd edge
WDI
W / T "L"
(S-19400 only)
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 36
6. 3. 2
Double Pulse Detection
When edges are input to WDI pin in order of falling and rising
VDD
1
2
3
4
4
CPOR
1
2
3
4
1
2
3
4
29 30 31 32
CWDT
Counter reset at the 1st edge
Only counter reset at the 2nd edge
WDI
W / T "L"
(S-19400 only)
WEN
(Active "H")
WDO
RST
(S-19401 only)
Figure 37
Double Pulse Non-detection
21
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
7.
Operation of low voltage detection
The voltage detection circuit________
detects a low voltage
if the power supply voltage falls below the detection voltage, and
_______
then "L" is output from the WDO pin and the RST pin (Only the S-19401 Series). The output is maintained until
the charge-discharge operation of the CPOR pin is performed 4 times.
The S-19400/19401 Series can detect a low voltage even if either the ___
CPOR pin or the WDT pin performs the
charge-discharge operation. In this case, the status of the WEN pin or the W / T pin does not have an affect.
VDD
1
2
1
2
3
4
1
2
3
4
CPOR
1
2
3
4
CWDT
WDI
"H" or "L"
W/T
"H" or "L"
(S-19400 only)
WEN
"H" or "L"*1
(Active "H")
WDO
RST
(S-19401 only)
Figure 38
*1. When the WEN pin is Disable, the charge-discharge operation of CWDT pin is not performed.
8.
____
WEN pin, WDI pin and W / T pin
___
Each of the WEN pin, the WDI pin and the W / T pin has a noise filter.
If the power supply voltage is 5.0 V, noise with a minimum pulse width of 200 ns can be eliminated.
22
1
2
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Standard Circuits
1.
____
S-19400 Series (Product with W / T pin)
VDD
VDD
WEN
WDI
WDO
W/T
VSS
CPOR
CWDT
CPOR*1
CWDT*2
Figure 39
2.
____
S-19401 Series (Product without W / T pin)
VDD
VDD
WDO
WEN
WDI
RST
VSS
CPOR
CPOR*1
CWDT
CWDT*2
Figure 40
*1.
*2.
Caution
Adjustment capacitor for reset output delay time (CPOR) should be connected directly to the CPOR pin and
the VSS pin.
Adjustment capacitor for watchdog output delay time (CWDT) should be connected directly to the CWDT pin
and the VSS pin.
A capacitor of 100 pF to 1 μF can be used for CPOR and CWDT.
The above connection diagram and constant will not guarantee successful operation.
Perform thorough evaluation using the actual application to set the constants.
23
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Precautions
• It will take time for the discharge operation to be performed if the capacitance of CPOR is extremely large at the low
voltage detection, so the discharge operation may not be completed by the time the power supply voltage exceeds
the detection voltage. In that case, since the charge-discharge operation of the CPOR pin is performed after the
discharge operation is completed, the delay time of the same time length as the discharge operation occurs in reset
time-out period (tRST).
• Select a capacitor which satisfies the following equation for CPOR and CWDT. If this condition is not satisfied, the
delay time of the same time length as the discharge operation occurs in tRST since the discharge operation of an
external capacitor connected to the CWDT pin is not completed by the time the CWDT pin initiates the next
charge-discharge operation.
CWDT / CPOR ≤ 600
• When the power supply voltage falls to 0.9 V or lower, set a time interval of 20 μs or longer by the time the power
supply is raised again. If the appropriate time length is not secured, the time-out period after raising the power
supply voltage may get delayed.
• When the time that the power supply voltage falls below the detection voltage is short, the S-19400/19401 Series
may not detect a voltage. In that case, the time-out period after raising the power supply voltage may get delayed.
___
• Since input pins (the WEN pin, the WDI pin and the W / T pin) in the S-19400/19401 Series are CMOS
configurations, make sure that an intermediate potential is not input when the S-19400/19401 Series operates.
________
_______
• Since the WDO pin and the RST pin are affected by external resistance and external capacitance, use the
S-19400/19401 Series after performing thorough evaluation with the actual application.
24
•
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
•
SII Semiconductor Corporation claims no responsibility for any disputes arising out of or in connection with any
infringement by products including this IC of patents owned by a third party.
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Characteristics (Typical Data)
1. Current consumption during operation (ISS1) vs. Input voltage (VDD)
5.0
WDT = OFF, −VDET(S) = 4.0 V, Ta = +25°C
WDT = ON, −VDET(S) = 4.0 V, Ta = +25°C, WDI input
5.0
Ta = +125C
4.5
ISS1 [A]
ISS1 [A]
4.0
3.0
2.0
1.0
Ta = 40C
4.0
Ta = +25C
3.5
3.0
0.0
0
1
2
3
4
5
4.0
6
4.5
VDD [V]
5.0
5.5
VDD [V]
6.0
6.5
2. Current consumption during operation (ISS1) vs. Temperature (Ta) 3. Detection voltage (−VDET), Release voltage (+VDET) vs. Temperature (Ta)
WDT = ON, −VDET(S) = 4.0 V, VDD = 5.0 V, WDI input
5.0
VDET, +VDET [V]
ISS1 [A]
4.0
3.0
2.0
1.0
0.0
4.5
−VDET(S) = 4.0 V
+VDET
4.0
VDET
3.5
3.0
40 25
0
25
50
Ta [C]
75
100
40 25
125
4. Reset time-out period (tRST) vs. Temperature (Ta)
0
30
30
0
40 25
25
50
Ta [C]
75
100
10
0
25
50
Ta [C]
75
100
125
75
100
125
30
20
10
0
40 25
25
50
Ta [C]
VDD = 5.0 V, CWDT = 470 pF
tWOUT [s]
tROUT [s]
20
0
40
40
30
40 25
7. Watchdog output delay time (tWOUT) vs. Temperature (Ta)
VDD = −VDET(S) + 1.0 V → −VDET(S) − 1.0 V,
CPOR = 2200 pF
0
10
125
6. Reset output delay time (tROUT) vs. Temperature (Ta)
125
20
0
0
100
VDD = 5.0 V, CWDT = 470 pF
40
tWDU [ms]
tRST [ms]
VDD = 5.0 V, CPOR = 2200 pF
10
75
5. Watchdog time-out period (tWDU) vs. Temperature (Ta)
40
20
25
50
Ta [C]
40 25
0
25
50
Ta [C]
75
100
125
25
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
8.
Reset time-out period (tRST) vs. CPOR
9.
VDD = 5.0 V, Ta = +25°C
10
tWDU [s]
tRST [s]
10
0.1
0.01
0.001
0.001
0.01
CPOR [F]
0.1
1
10. Nch driver output current (IWOUT) vs. Input voltage (VDD)
VDS = 0.4 V, −VDET(S) = 4.0 V
6.0
Ta = +25C
IWOUT [mA]
1
0.1
0.01
0.0001
0.0001
26
VDD = 5.0 V, Ta = +25°C
100
1
4.0
Ta = 40C
2.0
Ta = +125C
0.0
Watchdog time-out period (tWDU) vs. CWDT
0
1
2
3
VDD [V]
4
5
0.001
0.0001
0.001
0.01
CWDT [F]
0.1
1
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
Thermal Characteristics
1. TMSOP-8
Tj = 125C max.
Power dissipation (PD) [W]
1.0
0.6
Board 1
0.63 W
0.4
0.2
0
Figure 41
1. 1
Board 2
0.75 W
0.8
0
50
100
150
Ambient temperature (Ta) [C]
Power Dissipation of Package (When Mounted on Board)
Board 1
76.2 mm
114.3 mm
114.3 mm
Table 10
Item
Thermal resistance value
(θja)
Size
Material
Number of copper foil layer
1
2
Copper foil layer
3
4
Thermal via
Item
Thermal resistance value
(θja)
Size
Material
Number of copper foil layer
1
2
Copper foil layer
3
4
Thermal via
Specification
160°C/W
114.3 mm × 76.2 mm × t1.6 mm
FR-4
2
Land pattern and wiring for testing: t0.070 mm
−
−
74.2 mm × 74.2 mm × t0.070 mm
−
Figure 42
1. 2
Board 2
76.2 mm
Table 11
Specification
133°C/W
114.3 mm × 76.2 mm × t1.6 mm
FR-4
4
Land pattern and wiring for testing: t0.070 mm
74.2 mm × 74.2 mm × t0.035 mm
74.2 mm × 74.2 mm × t0.035 mm
74.2 mm × 74.2 mm × t0.070 mm
−
Figure 43
27
FOR AUTOMOTIVE 125°C OPERATION LOW CURRENT CONSUMPTION WATCHDOG TIMER WITH RESET FUNCTION
Rev.2.0_00
S-19400/19401 Series
2. HSNT-8(2030)
Tj = +125°C max.
Power dissipation (PD) [W]
1.0
0.6
Board 1
0.55 W
0.4
0.2
0
Figure 44
2. 1
Board 2
0.74 W
0.8
0
50
100
150
Ambient temperature (Ta) [C]
Power Dissipation of Package (When Mounted on Board)
Board 1
76.2 mm
Table 12
114.3 mm
Item
Thermal resistance value
(θja)
Size
Material
Number of copper foil layer
1
2
Copper foil layer
3
4
Thermal via
Specification
181°C/W
114.3 mm × 76.2 mm × t1.6 mm
FR-4
2
Land pattern and wiring for testing: t0.070 mm
−
−
74.2 mm × 74.2 mm × t0.070 mm
−
Figure 45
2. 2
Board 2
76.2 mm
114.3 mm
Table 13
Figure 46
28
Item
Thermal resistance value
(θja)
Size
Material
Number of copper foil layer
1
2
Copper foil layer
3
4
Thermal via
Specification
135°C/W
114.3 mm × 76.2 mm × t1.6 mm
FR-4
4
Land pattern and wiring for testing: t0.070 mm
74.2 mm × 74.2 mm × t0.035 mm
74.2 mm × 74.2 mm × t0.035 mm
74.2 mm × 74.2 mm × t0.070 mm
−
2.90±0.2
8
5
1
4
0.13±0.1
0.2±0.1
0.65±0.1
No. FM008-A-P-SD-1.2
TITLE
TMSOP8-A-PKG Dimensions
No.
FM008-A-P-SD-1.2
ANGLE
UNIT
mm
SII Semiconductor Corporation
2.00±0.05
4.00±0.1
4.00±0.1
1.00±0.1
+0.1
1.5 -0
1.05±0.05
0.30±0.05
3.25±0.05
4
1
5
8
Feed direction
No. FM008-A-C-SD-2.0
TITLE
TMSOP8-A-Carrier Tape
FM008-A-C-SD-2.0
No.
ANGLE
UNIT
mm
SII Semiconductor Corporation
16.5max.
13.0±0.3
Enlarged drawing in the central part
13±0.2
(60°)
(60°)
No. FM008-A-R-SD-1.0
TITLE
TMSOP8-A-Reel
No.
FM008-A-R-SD-1.0
ANGLE
UNIT
QTY.
4,000
mm
SII Semiconductor Corporation
2.0±0.1
8
5
(1.70)
1
4
+0.05
0.08 -0.02
0.5
0.23±0.1
No. PP008-A-P-SD-2.0
The heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
TITLE
DFN-8/HSNT-8-A-PKG Dimensions
No.
PP008-A-P-SD-2.0
ANGLE
UNIT
mm
SII Semiconductor Corporation
+0.1
ø1.5 -0
2.0±0.05
4.0±0.1
0.25±0.05
+0.1
ø1.0 -0
0.60±0.05
4.0±0.1
2.3±0.05
4 321
5 6 78
Feed direction
No. PP008-A-C-SD-1.0
TITLE
DFN-8/HSNT-8-A-Carrier Tape
No.
PP008-A-C-SD-1.0
ANGLE
UNIT
mm
SII Semiconductor Corporation
+1.0
9.0 - 0.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PP008-A-R-SD-1.0
TITLE
DFN-8/HSNT-8-A-Reel
No.
PP008-A-R-SD-1.0
QTY.
ANGLE
UNIT
5,000
mm
SII Semiconductor Corporation
1.6
0.30
0.50
No. PP008-A-L-SD-1.0
TITLE
No.
DFN-8/HSNT-8-A
-Land Recommendation
PP008-A-L-SD-1.0
ANGLE
UNIT
mm
SII Semiconductor Corporation
Disclaimers (Handling Precautions)
1.
All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2.
The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
SII Semiconductor Corporation is not responsible for damages caused by the reasons other than the products or
infringement of third-party intellectual property rights and any other rights due to the use of the information described
herein.
3.
SII Semiconductor Corporation is not responsible for damages caused by the incorrect information described herein.
4.
Take care to use the products described herein within their specified ranges. Pay special attention to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
SII Semiconductor Corporation is not responsible for damages caused by failures and/or accidents, etc. that occur
due to the use of products outside their specified ranges.
5.
When using the products described herein, confirm their applications, and the laws and regulations of the region or
country where they are used and verify suitability, safety and other factors for the intended use.
6.
When exporting the products described herein, comply with the Foreign Exchange and Foreign Trade Act and all
other export-related laws, and follow the required procedures.
7.
The products described herein must not be used or provided (exported) for the purposes of the development of
weapons of mass destruction or military use. SII Semiconductor Corporation is not responsible for any provision
(export) to those whose purpose is to develop, manufacture, use or store nuclear, biological or chemical weapons,
missiles, or other military use.
8.
The products described herein are not designed to be used as part of any device or equipment that may affect the
human body, human life, or assets (such as medical equipment, disaster prevention systems, security systems,
combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment,
aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle
use or other uses. Do not use those products without the prior written permission of SII Semiconductor Corporation.
Especially, the products described herein cannot be used for life support devices, devices implanted in the human
body and devices that directly affect human life, etc.
Prior consultation with our sales office is required when considering the above uses.
SII Semiconductor Corporation is not responsible for damages caused by unauthorized or unspecified use of our
products.
9.
Semiconductor products may fail or malfunction with some probability.
The user of these products should therefore take responsibility to give thorough consideration to safety design
including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing
injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction.
The entire system must be sufficiently evaluated and applied on customer's own responsibility.
10. The products described herein are not designed to be radiation-proof. The necessary radiation measures should be
taken in the product design by the customer depending on the intended use.
11. The products described herein do not affect human health under normal use. However, they contain chemical
substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips
may be sharp. Take care when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products described herein, comply with the laws and ordinances of the country or region where
they are used.
13. The information described herein contains copyright information and know-how of SII Semiconductor Corporation.
The information described herein does not convey any license under any intellectual property rights or any other
rights belonging to SII Semiconductor Corporation or a third party. Reproduction or copying of the information
described herein for the purpose of disclosing it to a third-party without the express permission of SII Semiconductor
Corporation is strictly prohibited.
14. For more details on the information described herein, contact our sales office.
1.0-2016.01
www.sii-ic.com