BE51-105-21 Echotel910

ECHOTEL® 910
Ultrasonic,
Tip Sensitive
Level Control
Echotel® 910 is an integral mounted ultrasonic tip sensitive
level switch with integrated DPDT relay. The Echotel® 910
is ideally suited for pump protection (also for vacuum),
overflow prevention, high or low level alarm in clean liquid
applications with or without foam.
Rugged and cost effective
F E AT U R E S
* Does not require any calibration.
* Dual electrical entries and various housings are standard available.
* A built-in averaging circuit ensures no false alarms due
to most effervescence or turbulences.
* Actuation is determined by the length of the transducer
and is available in lengths between 3 cm (1.20") and
254 cm (100").
* All materials exposed to process in 316/316L SST
(1.4401/1.4404).
Field
selectable high/low level failsafe.
*
Weatherproof housing
threaded sensor
ATEX housing
flanged sensor
A P P L I C AT I O N S
• LIQUIDS: Any clean liquids.
• VESSELS: Any mounting position.
• PROCESS CONDITIONS: Unaffected by
- shifting dielectric, density, or PH
- presence of foam, turbulence, visible vapors
- fast drain/fill rates
- transducer coating and air bubbles
- vacuum conditions.
P R I N C I P L E O F O P E R AT I O N
The Echotel® 910 operates on a two crystal “transmitreceive” principle. The signal is converted into ultrasonic
energy and transmitted across the sensing gap toward the
receiver crystal. When there is air in the gap, the high frequency ultrasonic energy will not be received. When there
is liquid in the gap, the ultrasonic energy will propagate
across the gap and actuate the relay.
A G E N C Y A P P R O VA L S
Agency
Approvals
ATEX
II 1/2 G Ex d+e/d IIC T6 Ga/Gb, flameproof enclosure
FM/CSA➀
Russian Authorisation Standards➀
Other approvals are available, consult factory for more details
T
➀ Consult factory for proper model numbers and classifications
NOTE: For applications where self-checking is required,
use Echotel® 961.
Air/Gas
Dry gap
R
Liquid
Wet gap
Worldwide level and flow solutions
Filling line
MOUNTING
High alarm
Low alarm
High alarm
Flats must
be vertical
Pump protection
Low alarm
Pump
E L E C T R I C A L S P E C I F I C AT I O N S
Description
Specification
Electronics Temperature
-40°C to +70°C (-40°F to +160°F)
Line Voltage (±10%)
240/120 V AC, 50-60 Hz – 24 V DC
Power Consumption
2.5 VA Nominal
Process Pressure/Temperature
Response Time
Repeatability
Output Relay
Housing
Sensor material
55,2 bar at -40°C to +120°C (800 psi at -40°F to +250°F)
Goldflash relay
Hermetically sealed relay
Failsafe
Electromagnetic compatibility
Approvals
EXPEDITE SHIP PLAN (ESP)
Several models are available for quick shipment, within
max. 4 weeks after factory receipt of purchase order,
through the Expedite Ship Plan (ESP).
Models covered by ESP service are conveniently colour
coded in the selection data charts.
To take advantage of ESP, simply match the colour coded
model number codes (standard dimensions apply).
ESP service may not apply to orders of ten units or more.
Contact your local representative for lead times on larger
volume orders, as well as other products and options.
S E L E C T I O N D ATA
Optional transducer mounting flanges
Thread-on mounting flanges can only be used in combination with 3/4" NPT process connection transducer.
0,5 s typical
± 2 mm (0.078")
DPDT, 8.0 A (resistive)
DPDT, 5.0 A (resistive)
IP 65, anti-corrosive painted cast aluminium or 316 stainless steel
316/316L SST (1.4401/1.4404)
Field selectable high or low level alarm
Meets CE requirements (EN 61326: 1997 + A1 + A2)
ATEX II 1/2 G Ex d+e/d IIC T6 Ga/Gb, flameproof enclosure
Other approvals are available, consult factory for more details
Thread-on flanges for use with 3/4" NPT-M connections
ANSI B16.5 flanges
316/316L SST
004-5867-021
004-5867-001
1"
150 lbs RF
004-5867-041
3"
150 lbs RF
004-5867-023
1 1/2" 150 lbs RF
2"
4"
6"
1"
150 lbs RF
150 lbs RF
150 lbs RF
300 lbs RF
1 1/2" 300 lbs RF
2"
3"
4"
6"
1"
300 lbs RF
300 lbs RF
300 lbs RF
300 lbs RF
600 lbs RF
1 1/2" 600 lbs RF
2
Part No.
Carbon steel
2"
600 lbs RF
004-5867-022
004-5867-024
004-5867-025
004-5867-042
004-5867-026
004-5867-027
004-5867-028
004-5867-029
004-5867-030
004-5867-051
004-5867-046
004-5867-049
004-5867-043
004-5867-002
004-5867-003
004-5867-004
004-5867-005
004-5867-044
004-5867-006
004-5867-007
004-5867-008
004-5867-009
004-5867-010
004-5867-050
004-5867-045
004-5867-048
S E L E C T I O N D ATA
A complete measuring system consists of:
1. One order code for ECHOTEL® series 910 electronics and transducer
2. Optional: Order code for thread-on mounting flanges, consult factory for other sizes or materials
BASIC MODEL NUMBER
9 1 0
Echotel® 910, ultrasonic level switch with relay
APPROVALS/ CABLE ENTRY / HOUSING MATERIALS
A
V
W
5
Weatherproof –
ATEX flameproof enclosure –
ATEX flameproof enclosure –
ATEX flameproof enclosure –
3/4" NPT
3/4" NPT
M20 x 1,5
3/4" NPT
dual cable entry, anti-corrosive coated aluminium
dual cable entry, anti-corrosive coated aluminium
dual cable entry, anti-corrosive coated aluminium
single cable entry, stainless steel
PROCESS CONNECTION - SIZE/TYPE
Threaded
M A
3/4" NPT
M 2
1" NPT
M 9
1" BSP (G 1")
ANSI Flanges
M 1
1"
M E
1"
M H
1"
M C
1 1/2"
M F
1 1/2"
M D
2"
M G
2"
M J
2"
Hygienic
M
M
M
M
M
M
3
4
5
6
7
8
150
300
600
150
300
150
300
600
lbs
lbs
lbs
lbs
lbs
lbs
lbs
lbs
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
ANSI
RF
RF
RF
RF
RF
RF
RF
RF
EN (DIN) Flanges
M R DN 25 PN 16/25/40
M X DN 25 PN 63/100
M S DN 40 PN 16/25/40
M Y DN 40 PN 63/100
M M DN 50 PN 16
M T DN 50 PN 25/40
M W DN 50 PN 63
M Z DN 50 PN 100
EN 1092-1 Type A
EN 1092-1 Type B2
EN 1092-1 Type A
EN 1092-1 Type B2
EN 1092-1 Type A
EN 1092-1 Type A
EN 1092-1 Type B2
EN 1092-1 Type B2
1 1/2" Tri-Clamp®
2" Tri-Clamp®
DN 25 DIN 11851
DN 32 DIN 11851
DN 40 DIN 11851
DN 50 DIN 11851
INPUT POWER / RELAY OUTPUT
1
2
0
240 V AC/8 A DPDT goldflash relay
224 V DC/8 A DPDT goldflash relay
120 V AC/8 A DPDT goldflash relay
J
K
H
240 V AC/5 A DPDT herm. sealed relay
224 V DC/5 A DPDT herm. sealed relay
120 V AC/5 A DPDT herm. sealed relay
ACTUATION LENGTH – Specify per cm (0.39") increment
Total insertion length = actuation length + 6 mm (0.25")
0 0 3
0 0 5
2 5 4
9 1 0
M
Minimum 3 cm (1.2") – for NPT connections
Minimum 5 cm (2.0") – for all other connections
Maximum 254 cm (100.0")
complete order code for Echotel® 910
X = product with a specific customer requirement
3
DIMENSIONS IN mm (inches)
87 (3.43)
cable entry
(both sides)
114
(4.49)
44 (1.73)
Weatherproof
dual entry: 87 (3.43)
single entry: 76 (3.00)
cable entry
114
(4.49)
25 (1.00)
45 (1.77)
44 (1.73)
Ø 22,9 (0.90)
6 (0.25)
ATEX
Ø 22,9 (0.90)
6 (0.25)
Threaded NPT
58 (2.28)
Actuation
length
Ø 22,9 (0.90)
Actuation
length
Actuation
length
29 (1.14)
35 (1.38)
Actuation
length
Actuation
length
Ø 22,9 (0.90)
6 (0.25)
6 (0.25)
Welded flange ANSI-EN (DIN)
Threaded BSP
Ø 22,9 (0.90)
6 (0.25)
Tri-Clamp®
DIN 11851
QUALITY ASSURANCE - ISO 9001:2008
THE QUALITY ASSURANCE SYSTEM IN PLACE AT MAGNETROL® GUARANTEES THE HIGHEST LEVEL OF QUALITY DURING THE DESIGN,
THE CONSTRUCTION AND THE SERVICE OF CONTROLS.
OUR QUALITY ASSURANCE SYSTEM IS APPROVED AND CERTIFIED TO ISO 9001:2008 AND OUR TOTAL COMPANY IS COMMITTED TO
PROVIDING FULL CUSTOMER SATISFACTION BOTH IN QUALITY PRODUCTS AND QUALITY SERVICE.
:2008
PRODUCT WARRANTY
ALL MAGNETROL MODEL 910 LEVEL CONTROLS ARE WARRANTED FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR TWO
FULL YEARS FROM THE DATE OF ORIGINAL FACTORY SHIPMENT. IF RETURNED WITHIN THE WARRANTY PERIOD; AND, UPON FACTORY INSPECTION OF THE CONTROL, THE CAUSE OF THE CLAIM IS DETERMINED TO BE COVERED UNDER THE WARRANTY; THEN, MAGNETROL INTERNATIONAL WILL REPAIR OR REPLACE THE CONTROL AT NO COST TO THE PURCHASER (OR OWNER) OTHER THAN TRANSPORTATION.
MAGNETROL® SHALL NOT BE LIABLE FOR MISAPPLICATION, LABOR CLAIMS, DIRECT OR CONSEQUENTIAL DAMAGE OR EXPENSE ARISING FROM THE INSTALLATION
OR USE OF THE EQUIPMENT. THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, EXCEPT, SPECIAL WRITTEN WARRANTIES COVERING SOME
MAGNETROL® PRODUCTS.
®
BULLETIN N°:
EFFECTIVE:
SUPERSEDES:
UNDER RESERVE OF MODIFICATIONS
Heikensstraat 6, 9240 Zele, België -Belgique
Tel. +32 (0)52.45.11.11 • Fax. +32 (0)52.45.09.93 • E-Mail: info@magnetrol.be
DEUTSCHLAND
Alte Ziegelei 2-4, D-51491 Overath
Tel. +49 (0)2204 / 9536-0 • Fax. +49 (0)2204 / 9536-53 • E-Mail: vertrieb@magnetrol.de
INDIA
C-20 Community Centre, Janakpuri, New Delhi - 110 058
Tel. +91 (11) 41661840 • Fax +91 (11) 41661843 • E-Mail: info@magnetrolindia.com
ITALIA
Via Arese 12, I-20159 Milano
Tel. +39 02 607.22.98 • Fax. +39 02 668.66.52 • E-Mail: mit.gen@magnetrol.it
RUSSIA
198095 Saint-Petersburg, Marshala Govorova street, house 35A, office 532
Tel. +7-812.702.70.87 • E-Mail: info@magnetrol.ru
U.A.E.
UNITED
KINGDOM
DAFZA Office 5EA 722 • PO Box 293671 • Dubai
Tel. +971-4-6091735 • Fax +971-4-6091736 • E-Mail: info@magnetrol.ae
Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL
Tel. +44 (0)1444 871313 • Fax +44 (0)1444 871317 • E-Mail: sales@magnetrol.co.uk
www.magnetrol.com
BENELUX
FRANCE
OUR NEAREST REPRESENTATIVE
BE 51-105.21
JUNE 2012
April 2011