X-Band QTRM Demonstrator - MAIA-009446-000000 QTRM - Quad Transmit Receive Module (4-Channel T/R Module) • • • • • • • • • • • • • • • RS485 Half-Duplex, 5.0 Mbps serial data bus for control and monitoring. DSP externally programmable via JTAG Factory amplitude and phase setting inaccuracies calibrated at the cold-wall operating temperature TX output power, HPA temperature, operating current and power supply health monitored and reported on request Automatic shut-down if internal temperature reaches a critical limit where damage could occur. Hysteresis applies. Positive supplies inhibited (with the exception of the digital control circuits) if negative supply is lost Direction cosines used for beam steering 4-bit array address code giving up to 16 QTRM sub-array (64- element array) TRM’s respond to individual address or broadcast messages. Module position assignment Ability to schedule up to 16 phase & amplitude settings for rapid execution. Array CAL allows end-user to add additional TRU phase & amplitude calibration. Read-back of set phase & amplitude values for each TRU. Selection of internal/external Clock source. European Manufacture. Electrical Performance Over TOP Unless Otherwise stated. Limits & Conditions are indicated values. Indicated values given per channel unless otherwise stated. Parameter Min. Typ. Max. Units Conditions Parameters: Common Centre Frequency Operating BW 9.5 GHz 1 GHz 50 TX/RX Switching Speed ns Target. From receipt of Gating pulse. Target 60dB Port-Port Isolation (Antenna) 40 dB Input Return Loss 10 dB Output Return Loss (Antenna) 10 dB Pulse Width 0.2 100 μS Duty Cycle 5 30 % RF Pulse Rise & Fall time 20 ns Data Control Rate 5.0 Mbps Global TX Gating Pulse Differential Beam Steering Pulse Differential No. of Stored Beam Settings Beam Steer Pulse Repetition Rate Power Supplies 250 +28,+6,-6 Scheduler Mode μS MHz 6 DC Input Consumption (Pk) Asynchronous UART RS485 Bus. Scheduler Mode – Beam direction change rate. V Ext. Clock (If used) DC Input CurrentPort) 80µS at 30% Duty max. Gate TX PA on 1.0 µS before RF pulse 16 15 See Note 1 ±20ppm LVDS Amps (pk) +28v supply, TX mode 1.8 Amps +6v supply, TX mode 0.2 Amps -6v supply 170 Watts (pk) TX mode Phase Control Phase Shift Range 0 355 deg 6-Bits, 64 States, 5.625° Steps. 2 4 deg See Note (2) RMS Error 9.0 – 10.0GHz 500 Switching Time ns Target. From receipt of Beam Steer pulse. Amplitude Control Attenuator Range 0 28.5 dB 5-Bits, 32 States, 0.9dB Steps. See Note (3) 0.4 0.6 dB See Note (4) ns Target. From receipt of Beam Steer pulse. RMS Error 9.0 – 10.0GHz Switching Time 500 Enviromental Operating Ambient: -30 to +70°C. Assumes QTRM is fixed to a cold-wall held at 35 ±10 °C Storage: -40 to +85°C; MTBF : 100,000 hrs target Notes (1) Can operate over a wider bandwidth at reduced performance. Limited by circulator bandwidth. (2) RMS Phase error given for reference attenuator state. (3) Up to 3dB reduction in useable attenuation range due to Calibration. (4) RMS Attenuator error given for reference phase state. (5) Figure given for Ref Attenuator state, Ref Phase State. (6) Noise Figure given for Ref Attenuator state, Ref Phase State. Electrical Performance Over TOP Unless Otherwise stated. Limits & Conditions are indicated values. Indicated values given per channel unless otherwise stated. Parameter Min. Typ. Max. Units Conditions Parameters: Transmit TX Psat 8.5 Watts (pk) 8.5 Watts output per antenna at Fo TX Gain >40 dB 8.5 to 10.5GHz TX Power Variation ± 0.5 dB Per 100MHz in operating bandwidth TX Power Variation ±1.0 Power Variation Between Outputs ±1.0 dB TX Input Power Level +5 dBm Spurious -60 dBc TX Phase Variation across pulse 4.0 deg Across 80µS Pulse at 30% Duty TX Amplitude Variation across pulse 0.5 dB Across 80µS Pulse at 30% Duty Harmonics -20 dBc TX Insertion Phase Balance ±15 deg Between any two channels.Target ±10 TX Insertion Phase Balance ±2.0 dB Between any two channels.Target ±1.0 9.0 to 10.0GHz For Ps at Out. Parameters: Receive RX P1dB 12 dBm RX Gain 35 dB RX Input IP3 -15 dBm RX Gain Variation ±0.25 dB Per 100MHz in operating bandwidth RX Gain Variation ±1.5 dB 9.0 to 10.0GHz dB See Note (6). Target <3dB RX Noise Figure 3.5 Receiver Protection 10 See Note (5) Watts (pk) Protection from reflected TX Power RX Insertion Phase Balance ±15 deg Between any two channels.Target ±10 RX Gain Balance ±2.0 dB Between any two channels.Target ±1.0 Recovery Time 100 ns Spurious Free Dynamic Range 88 dB 5MHz Bandwidth Mechanical Size: 150(L) x 59.5(W) x 14.5mm(D) excluding connectors Mass: < 200gm, target <150gm RF Connectors: Male GPO hermetic shroud (Corning Gilbert) DC Connectors: 177-704H37SS (Glenair Hermetic Micro-D) Cooling Method: Heatsink mounted, forced air cooled for demonstration purposes. (Unit designed to mount against a liquid cooled cold-wall, meeting height constraints for stacked QTRM’s in X and Y to form a 2D array) Notes (1) Can operate over a wider bandwidth at reduced performance. Limited by circulator bandwidth. (2) RMS Phase error given for reference attenuator state. (3) Up to 3dB reduction in useable attenuation range due to Calibration. (4) RMS Attenuator error given for reference phase state. (5) Figure given for Ref Attenuator state, Ref Phase State. (6) Noise Figure given for Ref Attenuator state, Ref Phase State. Functional Block Diagram Core Chip Tx Switch P.A MPA Amp 2 ... . Common switch Control Logic 0/+3.3V A4 P0 ... . Amp 1 Parallel Interface A0 Antenna Port Pwr Mon P5 Limiter LNA Rx In Rx Switch LNA TRM Element Block diagram RF Subsystem controls. To TRM's Antenna Port 1 TRM Element1 RF 1 In/Out .. .. .. PLD Antenna Port 2 +28v +6.0v -6.0v LDO's Flash memory SDRAM DATA BUS TRM Element 2 ADDR BUS Coarse Atten Tx Out Antenna Port 3 TRM Element 3 RF 2 In/Out Processor Antenna Port 4 TRM Element 4 RS485 ASYNC Bus Tx/Rx Trigg To PLD To PLD Beam QTRM Block diagram Typical Performance DC Pin-Out Connection’s (MWDM2L-37 Series) Pin No. Description 1(7) Ext_CLK +ve 2(7) 3 Pin No. Description Pin No. Description Pin No. Description ADDR_4 21 +6V 31 Beam +ve Ext_CLK -ve 11 12(8) WD_DIS_DSP 22 GND 32 TxPreTrigg +ve ADDR_5 13(8) EM_VDD 23 GND 33 Beam -ve 4 Spare 14(8) TDO_DSP 24 GND 34 +28V 5 Spare 15(8) TMS_DSP 25 GND 35 +28V 6 GND 16(8) TRSTn_DSP 26 GND 36 +28V 7 ADDR_0 17(8) EMUn_DSP 27 GND 37 +28V 8 ADDR_1 18(8) TDI_DSP 28 RS485 -ve 9 ADDR_2 19(8) TCK_DSP 29 RS485 +ve 10 ADDR_3 20 -6V 30 Tx PreTrigg -ve Notes (7) External Clock (if used) 100MHz LVDS ±20ppm (8) For Factory use only, do not connect leave open circuit. Whilst every effort is made to ensure the accuracy of the information contained in this brochure, no responsibility can be accepted for any errors and/or omissions. Descriptions and specifications of products are subject to change without notice. +44 (0) 1908.574.200 [email protected] http://rf2m.apitech.com +1 855.294.3800 www.apitech.com