160 MHz SAW Filter 6.6 MHz Bandwidth Part Number SF0160BA02497S DESCRIPTION • • • 160 MHz SAW bandpass filter with 6.6 MHz bandwidth. 13.3 x 6.5 mm LCC package. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical: Frequency : Relative Magnitude : Relative Magnitude : Phase Linearity : Group Delay : S11 (135-185 MHz) 5 10 1 10 100 MHz/div dB/div dB/div deg/div ns/div S22 (135-185 MHz) IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.idt.com DSSF0160BA02497S Rev - 28-Mar-2007 Page 1 of 3 160 MHz SAW Filter 6.6 MHz Bandwidth Part Number SF0160BA02497S SPECIFICATION Parameter Center Frequency, FC 1 Insertion Loss (@ Fc) 1 dB Bandwidth Lower 1dB Frequency Upper 1dB Frequency Lower 30 dB Frequency Upper 30 dB Frequency Lower 45 dB Frequency Upper 45 dB Frequency Rejection (10 to 152 MHz) 3 Rejection (168 to 188 MHz) 3 Rejection (188 to 250 MHz) 3 Passband Amplitude Ripple 2 Passband Group Delay Ripple 2 Source and Load Impedance Temperature Coefficient of Frequency Ambient Temperature Notes: Min 159.7 6.6 163.2 152.4 152 45 45 43 - - Typ 160.0 12.4 7.1 156.45 163.56 154.5 166.1 153.6 166.7 50 48 45 0.3 40 50 -87 25 Max 160.3 14 156.8 167.6 168 0.5 60 Units MHz dB MHz MHz MHz MHz MHz MHz MHz dB dB dB dB p-p ns p-p ohms ppm/˚C ˚C - 1. Fixed reference frequency. All bandwidths are centered at this frequency. 2. Defined over Fc+/-2.6 MHz. 3. Dependent upon PC board layout. MAXIMUM RATINGS Parameter Storage Temperature Range Input Power Level Min Max -40 - 85 10 Units ˚C dBm MATCHING CIRCUIT 12 6 Input 50 Ω Single ended Output 50 Ω Single ended 11 5 Notes • Matching components are not required. IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.idt.com DSSF0160BA02497S Rev - 28-Mar-2007 Page 2 of 3 160 MHz SAW Filter 6.6 MHz Bandwidth Part Number SF0160BA02497S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are ±0.15 mm except where indicated. Pad Configuration: Input: 12 Input return: 11 Output: 6 Output return: 5 Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. © 2007 All rights reserved. IDT • SAW Products • 324 Clark Street, Worcester, MA 01606, USA • Ph 1-508-852-5400 • Fax 1-508-852-8456 www.idt.com DSSF0160BA02497S Rev - 28-Mar-2007 Page 3 of 3