89086

REVISIONS
LTR
DESCRIPTION
DATE
APPROVED
A
Added suggested source of supply.
10 Jan 90
David E. Moore
B
Deleted suggested source of supply.
29 Jun 90
David E. Moore
C
Deleted and added suggested sources of supply.
Modified 3.1.2 and figure 1. Added note for
standoff. Editorial changes throughout.
24 Feb 92
David E. Moore
D
Changes in accordance with NOR 5910-R019-96
23 May 96
Andrew R. Ernst
E
Added and removed suggested sources of
supply.
25 August 99
Kendall A. Cottongim
F
Removed suggested source of supply.
10 May 00
Kenneth A. Bernier
G
Editorial changes made throughout.
6 October 2004
Kendall A. Cottongim
H
Changed drawing to source control with
approved sources of supply. Added pure tin
prohibition paragraph 3.1.3 and manufacturer
eligibility paragraph 3.14. Editorial changes.
15 Dec 09
Michael A. Radecki
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
DEFENSE LOGISTICS AGENCY
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
Prepared in accordance with ASME Y14.100
REV STATUS
OF PAGES
PMIC N/A
Original date of
drawing:
27 June 1989
REV
H
H
H
H
H
H
H
PAGES
1
2
3
4
5
6
7
DESIGN ACTIVITY
PREPARED BY
ROBERT E. GRILLOT
CHECKED BY
HERALDINE JOHNSON
APPROVED BY
DAVID E. MOORE
SIZE
A
REV
AMSC N/A
Source control drawing
DEFENSE ELECTRONIC SUPPLY CENTER
DAYTON, OH 45444-5000
TITLE
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE,
NETWORK, (4 CAPACITOR SECTIONS) CG
CODE IDENT. NO.
14933
DWG NO.
H
PAGE
89086
1
OF
7
5910-E453
1. SCOPE
1.1 Scope. This drawing and MIL-PRF-20 describe the complete requirements for single-in-line packaged multilayer ceramic
capacitor networks.
1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows:
89086-
XX
Drawing
number
Dash number
(see table I)
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not
include documents cited in other sections of this specification or recommended for additional information or as examples. While every
effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified
requirements of documents in sections 3 and 4 of this specification, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this
document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation
or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-20
-
Capacitors, Fixed, Ceramic Dielectric (Temperature Compensating), Established Reliability and
Non-Established Reliability, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-202
MIL-STD-1285
-
Electronics and Electrical Component Parts.
Marking of Electrical and Electronic Parts.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document
Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this
document and the references cited herein, the text of this document takes precedence. Nothing in this document, however,
supersedes applicable laws and regulations unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-20 and herein (see
figure 1).
3.1.1 Leads. Leads shall be as specified on figure 1.
3.1.2 Case. Molded or conformally coated.
3.1.3 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of
capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by
mass (see 6.3).
3.1.4 Operating temperature range. The operating temperature range shall be -55°C to +125°C.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
89086
REV H
PAGE
2
Inches
.002
.003
.004
.010
.012
.015
.018
mm
0.05
0.08
0.10
0.25
0.30
0.38
0.46
Inches
.058
.060
.100
.115
.135
.300
.850
mm
1.47
1.52
2.54
2.92
3.43
7.62
21.59
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Standoff shape is optional. The minimum height of the standoff shall be .015 (0.38 mm).
4. Lead spacing .100 ±.010 (25.4 ± 0.25 mm) noncumulative.
FIGURE 1. Case dimensions and configuration.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
89086
REV H
PAGE
3
3.2 Electrical characteristics.
3.2.1 Rated voltage. The rated voltage shall be 100 V dc at +85°C, 50 V dc at +125°C.
3.2.2 Dielectric type. CG (0 ±30ppm/°C), in accordance with MIL-PRF-20.
3.2.3 Temperature coefficient and capacitance drift. In accordance with MIL-PRF-20.
3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25°C.
3.2.5 Dissipation factor (+25°C). 0.1 percent maximum (measured under the same conditions as capacitance).
3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25°C, rated voltage: 100,000
megohms or 1,000 megohms microfarad, whichever is less.
3.2.7 Dielectric withstanding voltage. Capacitors shall withstand a dc test potential of 250 percent of rated voltage for a period of
not less than 1 second nor more than 5 seconds at +25°C. The charging current shall not exceed 50 milliamperes.
3.2.8 Q factor. 1000 or greater (measured under the same conditions as capacitance).
3.2.9 Capacitance tolerance. J = ±5 percent, K = ±10 percent.
3.3 Solderability of terminals. In accordance with MIL-PRF-20.
3.4 Vibration. In accordance with method 204 of MIL-STD-202, test condition B (10 to 20,000 Hz, 15 g’s).
3.5 Shock. In accordance with MIL-PRF-20.
3.6 Immersion cycling. In accordance with MIL-PRF-20.
3.7 Moisture resistance. In accordance with MIL-PRF-20.
3.8 Life. 200 percent of rated voltage applied at +125°C for 1,000 hours.
3.9 Thermal shock. In accordance with method 107 of MIL-STD-202, test condition B except low temperature is -55°C.
3.10 Voltage conditioning. In accordance with MIL-PRF-20, 200 percent of rated voltage.
3.11 Terminal strength. Capacitors shall withstand a steady pull of 5 pounds for 5 seconds in a direction parallel to the leads.
3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified
herein (see 1.2), the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum.
3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials
should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance
requirements, and promotes economically advantageous life cycle costs.
3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the
MIL-PRF-20, MIL-PRF-123, or MIL-PRF-49470 Qualified Products Database for at least one part, or perform the group A and group B
inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA.
3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved
source of supply.
3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or
appearance.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
89086
REV H
PAGE
4
4. VERIFICATION
4.1 Sampling and inspection. Qualification sampling and inspection are not required.
4.2 Conformance inspection.
4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A (ER) and
group B inspections of MIL-PRF-20, provided they are listed in this drawing. PPM testing and calculation is not applicable.
4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu
of performing group B tests (see 6.2d).
TABLE I. Electrical characteristics.
DSCC
drawing
8908601
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Capacitance
Capacitance
tolerance
10 pF
10 pF
12 pF
12 pF
15 pF
15 pF
18 pF
18 pF
22 pF
22 pF
27 pF
27 pF
33 pF
33 pF
39 pF
39 pF
47 pF
47 pF
56 pF
56 pF
68 pF
68 pF
82 pF
82 pF
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
DSCC
drawing
8908625
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Capacitance
Capacitance
tolerance
100 pF
100 pF
120 pF
120 pF
150 pF
150 pF
180 pF
180 pF
220 pF
220 pF
270 pF
270 pF
330 pF
330 pF
390 pF
390 pF
470 pF
470 pF
560 pF
560 pF
680 pF
680 pF
820 pF
820 pF
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2).
When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the
responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control
Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands.
Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CDROM products, or by contacting the responsible packaging activity.
6. NOTES
(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)
6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified
military devices that will perform the required function are not available for original equipment manufacturer application. This drawing
is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
89086
REV H
PAGE
5
a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and
will not be used for new design.
6.2 Ordering data. The contract or purchase order should specify the following:
a.
Complete PIN (see 1.2).
b.
Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed
conformance inspection with each shipment of parts by the manufacturer.
c.
Requirements for packaging and packing.
d.
Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements.
e.
Requirements for notification of change of product to acquiring activity, if applicable.
6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth
problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical
operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not
prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional
information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin).
6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared
specification or drawing.
6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and
the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at
[email protected] or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus OH
43218-3990 or by telephone (614) 692-0561 or DSN 850-0561.
6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become
available. Assistance in the use of this drawing may be achieved online at [email protected] or by contacting Defense Supply
Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus OH 43218-3990 or by telephone (614) 692-0561 or DSN 8500561.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
89086
REV H
PAGE
6
DSCC drawing
PIN
89086-
Vendor similar
type 1/
DSCC drawing
PIN
89086-
Vendor similar
type 1/
Vendor
CAGE
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
N/A
SPB11A100KH8
N/A
SPB11A120KH8
N/A
SPB11A150KH8
N/A
SPB11A180KH8
SPB11A220JH8
SPB11A220KH8
SPB11A270JH8
SPB11A270KH8
SPB11A330JH8
SPB11A330KH8
SPB11A390JH8
SPB11A390KH8
SPB11A470JH8
SPB11A470KH8
SPB11A560JH8
SPB11A560KH8
SPB11A680JH8
SPB11A680KH8
SPB11A820JH8
SPB11A820KH8
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
SPB11A101JH8
SPB11A101KH8
SPB11A121JH8
SPB11A121KH8
SPB11A151JH8
SPB11A151KH8
SPB11A181JH8
SPB11A181KH8
SPB11A221JH8
SPB11A221KH8
SPB11A271JH8
SPB11A271KH8
SPB11A331JH8
SPB11A331KH8
SPB11A391JH8
SPB11A391KH8
SPB11A471JH8
SPB11A471KH8
SPB11A561JH8
SPB11A561KH8
SPB11A681JH8
SPB11A681KH8
SPB11A821JH8
SPB11A821KH8
96095
Vendor name and address
Olean Advanced Products
A Division of AVX Corporation
1695 Seneca Avenue
Olean NY 14760-3736
1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
89086
REV H
PAGE
7
Similar pages