SML-P1 series PICOLEDTM Datasheet lFeatures lOutline • Ultra compact, thin size 1.0×0.6mm • Original device technology enables high brightness and high reliability • Lead Free/RoHS Compliant. lSize 1006 (0402) 1006 (0402) 1.0×0.6mm (t=0.2mm) 1.0×0.6mm (t=0.2mm) Color Type V U D Y M P E B WB lDimensions lRecommended Solder Pattern Tolerance : ±0.05 (unit : mm) (unit : mm) lSpecifications Part No. Chip Structure SML-P12VT(R) Emitting Color Red Absolute Maximum Ratings (Ta=25ºC) Peak Forward Reverse Operating Temp. Storage Temp. Dissipation Current Current Voltage PD(mW) IF(mA) IFP(mA) VR(V) Topr(ºC) Tstg(ºC) Power Forward 50 Electrical and Optical Characteristics (Ta=25ºC) Forward Voltag VF Reverse Current IR Typ. (V) IF Max. VR (mA) (mA) (V) 2.0 SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) AIGaInP on GaAs Orange 52 Yellowish Green SML-P12PT(R) Green SMLP13EC8T Bluish Green SCMP13WBC8W InGaN 100*1 2.1 20 4 Yellow SML-P12MT(R) SMLP13BC8T 20 Blue 5 54 -40 to +85 -40 to +100 34 33 100 2.2 3.0 10 50*1 2.9 White 5 625 630 635 615 620 625 602 605 608 587 590 593 569 572 575 10 35 557 560 563 4.0 13 520 527 535 56 (110) 465 470 475 25 60 85 20 40 100 20 130 5 (x, y) (0.30, 0.30) 9.0 (25) 90 150 5 *1 : Duty 1/10, 1kHz *2 : Reference *PICOLEDTM is ROHM's pending trademark. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 5 Dominant Wavelength lD Luminous Intensity IV IF Min. Typ. Min.*2 Typ. Max.*2 IF (nm) (nm) (nm) (mA) (mcd) (mcd) (mA) 1/8 2013.05 - Rev.D Data Sheet SML-P1 series lElectrical Characteristics Curves Fig.2 Luminous Intensity Atmosphere Temperature SML-P12VT(R) SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) SML-P12MT(R) SML-P12PT(R) Ta=25ºC RELATIVE LUMINOUS INTENSITY [a.u.] FORWARD CURRENT : IF [mA] Fig.1 Forward Current - Forward Voltages FORWARD VOLTAGE : VF [V] Fig.4 Derating MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Ta=25ºC FORWARD CURRENT : IF [mA] www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. SML-P12VT(R) SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) SML-P12MT(R) SML-P12PT(R) ATMOSPHERE TEMPERATURE : Ta [ºC] Fig.3 Luminous Intensity - Forward Current SML-P12VT(R) SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) SML-P12MT(R) SML-P12PT(R) IF=20mA SML-P12VT(R) SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) SML-P12MT(R) SML-P12PT(R) AMBIENT TEMPERATURE : Ta [ºC] 2/8 2013.05 - Rev.D Data Sheet SML-P1 series lElectrical Characteristics Curves Fig.2 Luminous Intensity Atmosphere Temperature SMLP13EC8T SMLP13BC8T SCMP13WBC8W Ta=25ºC RELATIVE LUMINOUS INTENSITY [a.u.] FORWARD CURRENT : IF [mA] Fig.1 Forward Current - Forward Voltages FORWARD VOLTAGE : VF [V] FORWARD CURRENT : IF [mA] www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. SMLP13EC8T SMLP13BC8T SCMP13WBC8W Fig.4 Derating MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Ta=25ºC ATMOSPHERE TEMPERATURE : Ta [ºC] Fig.3 Luminous Intensity - Forward Current SMLP13EC8T SMLP13BC8T SCMP13WBC8W IF=20mA SMLP13EC8T SMLP13BC8T SCMP13WBC8W AMBIENT TEMPERATURE : Ta [ºC] 3/8 2013.05 - Rev.D Data Sheet SML-P1 series lSpectrum Data IF=20mA 0.8 0.6 0.4 SMLP13BC8T SCMP13WBC8W 0.8 0.6 0.4 0.2 0.2 0.0 IF=5mA 1 INTENSITY [a.u.] INTENSITY [a.u.] 1.0 SML-P12VT(R) SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) SML-P12MT(R) SML-P12PT(R) 380 480 580 680 0 780 380 WAVELENGTH [nm] 480 580 680 780 WAVELENGTH [nm] * Please take this data as a reference data for the samples are measured randomly. * The data is relativized for each color. It is NOT to show the spectrum peaks are equal. lViewing Angle SCANNING ANGLE (deg) SCANNING ANGLE (deg) RELATIVE INTENSITY RELATIVE INTENSITY SCANNING ANGLE (deg) SCANNING ANGLE (deg) RELATIVE INTENSITY RELATIVE INTENSITY www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 4/8 SML-P12VT(R) SML-P12UT(R) SML-P12DT(R) SML-P12YT(R) SML-P12MT(R) SML-P12PT(R) SMLP13EC8T SMLP13BC8T SCMP13WBC8W 2013.05 - Rev.D Data Sheet SML-P1 series lRank Reference of Brightness Red(V,U) Rank Iv (mcd) SML-P12VT SML-P12UT (Ta=25ºC, IF＝20mA) G H J K L 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 M N P Q R 10 to 16 16 to 25 25 to 40 M N P 10 to 16 16 to 25 25 to 40 M N P 10 to 16 16 to 25 25 to 40 N P 16 to 25 25 to 40 M N P Q 9 to 14 14 to 22 22 to 36 36 to 56 M N P Q 9 to 14 14 to 22 22 to 36 36 to 56 T U S T U V W 40 to 63 63 to 100 100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000 Orange(D) Rank Iv (mcd) SML-P12DT (Ta=25ºC, IF＝20mA) G H J K L 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 Q R S T U V W 40 to 63 63 to 100 100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000 Yellow(Y) Rank Iv (mcd) SML-P12YT X 1000 to 1600 (Ta=25ºC, IF＝20mA) G H J K L 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 Q R S T U V W 40 to 63 63 to 100 100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000 Green(M,P) Q R S T U V W 40 to 63 63 to 100 100 to 160 160 to 250 250 to 400 400 to 630 630 to 1000 Bluish Green(E) G X 1000 to 1600 (Ta=25ºC, IF＝20mA) Rank G H J K L M Iv (mcd) 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 SML-P12MT SML-P12PT Rank Iv (mcd) X 1000 to 1600 X 1000 to 1600 (Ta=25ºC, IF＝5mA) H J K L 0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9.0 R S T U V W 56 to 90 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900 SMLP13EC8T Blue(B) Rank Iv (mcd) (Ta=25ºC, IF＝5mA) G H J K L 0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9.0 R S T U V W 56 to 90 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900 SMLP13BC8T White(WB) Rank Iv (mcd) (Ta=25ºC, IF＝5mA) N P Q 14 to 22 22 to 36 36 to 56 R S V W 56 to 90 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900 SCMP13WBC8W lChromaticity Diagram CIE y K [Chromaticity Coordimates] F (Ta=25ºC, IF＝5mA) H A A x 0.28 F y x H y x K y x 0.248 0.283 0.305 0.287 0.295 0.304 0.296 0.276 0.304 0.33 y 0.33 0.307 0.315 0.33 0.36 0.283 0.305 0.307 0.315 0.311 0.294 0.33 0.318 0.264 0.267 0.287 0.295 0.296 0.276 0.311 0.294 Measurement tolerance : 0.02 CIE x www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 5/8 2013.05 - Rev.D Data Sheet SML-P1 series 4.00 ±0 . 1 lTaping ± 0. 1 φ1 .5 +0 . 1 0 5 .5 0 0 ～0 . 50 8. 0 0 3 . 50 ±0 . 0 5 1 .7 5 A 1 . 10 ± 0. 0 5 2 .0 0 ± 0 .0 5 0 .7 0 ±0 . 0 5 + 0 . 05 0. 2 8 - 0 .0 3 A部詳 細 Enlarged drawing of ‟A” Packaging quantity Pulling Direction +1 0 0 -3 φ60 φ 18 0 ±1 φ1 3 11 . 4 (unit : mm) (Note) Tolerance is 0.1mm, unless otherwise specified. lPart No. Construction lPacking Specification ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags. Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card inside the bag is available upon request. Please contact the nearest sales office or distributer if necessary. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 6/8 2013.05 - Rev.D Data Sheet SML-P1 series lAttention Points In Handling This product was developed as a surface mount LED especially suitable for reflow soldering. Please take care of following points when using this device. 1.DESIGNING OF PCB As for a recommendable solder pattern, Please refer to Fig ”Recommended Solder Pattern”. The size and direction of the pad pattern depend on the condition of the PCB. This product of structured with rear/bottom electrode to be soldered. The formation of solder fillet is not guaranteed due to its electrode shape Reference Mask open area ratio：80% Mask thickness ：80 to 100mm Additional notification of mounting : We recommend additional facility of mounting Machine due to small size package which might be haven electrification, and product might be moved in the taping pocket. And the mounting production efficiency will be decreased. Ex) Magnet facility etc. 2.SOLDERING (Sn-Cu, Sn-Ag-Cu, Sn-Ag-Bi-Cu) LED products do not contain reinforcement materials such as glass fillers. Therefore, thermal stress by soldering greatly influences its reliability. The temperature conditions for reflow soldering should therefore be set up according to the characteristic of this product. (See Fig-1) Number of reflow process shall be max 2 times and these processes shall be performed in a row. 300 Max.260ºC, Within 250 200 140 to 180ºC 230 to 260ºC 150 100 50 Min.1 min Max. 0 (Fig-1) Cooling process to normal temperature shall be required between the first and the second soldering process. (Fig-2) SOLDERING OPERATION SOLDERING IRON 1) SOLDER USED Sn-Cu, Sn-Ag-Cu, Sn-Ag-Bi-Cu 2) SOLDERING CONDITION LED products do not contain reinforcement material such as a glass fillers. So thermal stress by soldering greatly influence its reliability. Please keep following points for manual soldering. ITEM a) Soldering iron SOLDERING LAND RECOMMENDED CONDITION Less than 30W, top of iron less than 3mm. Condition) Temp. of iron top less than b) Heating method 400ºC within 3 sec. Heating on PCB pattern, not direct to the LED. (Fig-2) c) Handling after soldering Please handle after the part temp. Goes down to room temp. 3.HANDLING AFTER MOUNTING (Fig.-3) As shown in the drawing on the right, in case outside force of about 700g is given to the device, stress is concentrated to the jointed part between mold resin and substrate. Therefore there is a possibility to breath the device or PCB. Careful handing is needed as ROHM cannot guarantee the falling of the device by outside force after mounting. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 7/8 2013.05 - Rev.D Data Sheet SML-P1 series 4.WASHING Please note the following points when washing is required after soldering. 4-1) WASHING SOLVENT Isopropyl alcohol or other alcohol solvent is recommendable. 4-2) TEMPERATURE Below 30ºC, immersion time ; within 3 minutes. 4-3) ULTRA SONIC WASHING Below 15W/1 litter of solvent tub or less. 4-4) COOLING Below 100ºC within 3 minutes. 5.EROSION GAS Utilization in erosion gas atmosphere may degenerate the plating surface which might cause deterioration of solder strength, optical characteristics, or functions. Please take precautions against occurrence of gas from the surrounding parts on the occasion of custody, and also after mounted on circuit board. 6.STORAGE At reflow soldering, the reliability of this product is often influenced by moisture absorption so we apply the packaging with moisture proof for better condition is use, please also note that 6-1) Not to be opened before using. 6-2) To be kept in our moisture proof packaging with some desiccant (SILICA GEL) after opening it. To be baked in case the SILICA GEL indicator its color from either blue to clear or green to pink. 6-3) Please use within 168 hours after the package was opened. (Condition at 30ºC, max.70%Rh.) In case it is not used within 168 hours, please put it back into our packaging. 6-4) BAKING Please bake under reel condition at 60ºC, 1 to 224 hours (max.20%Rh) after un-sealing. While baking is done, the reel and emboss tape may be easily deformed. Please be careful not to give any stress. 7.LIFE TIME Blue led die used in this product will cause reduction of luminous intensity due to epoxy resin discoloration depending on the using conditions and environmental. Please inquire our sales contact if long life time is required on your application. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 8/8 2013.05 - Rev.D Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications : 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensur the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. R1102A