Model # WN6109 Standard Microwave Amplifier Frequency Range: 500 kHz to 300 MHz Features • Low Frequency Operation: 500 kHz to 300 MHz • High Output Power: +28.5 dBm Typical • High Second Order Intercept: +75 dBm Typical Model WN6109 is a lower frequency amplifier covering 500 kHz to 300 MHz. This high linearity design utilizes a hermetically sealed housing for superior environmental protection. This standard design may also be ordered in a MIL-STD-883 screened version (Model #SWN6109) All specification ratings are based on measurements in a 50 Ω (ohm) system with a DC supply of 15 volts and a voltage tolerance of +/- 2%. Technical Specifications Maximum Ratings Parameter Unit Typical Min/Max Frequency Range MHz 500 kHz to 300 MHz 500 kHz to 200 MHz Gain dB 10.8* (+/- 0.2 dB) 9.5* (+/- 0.7 dB) Noise Figure dB 4.5 5.7 Output Power @ 1 dB Compression dBm 28.5 27 Output 3rd Order Intercept dBm 44 - Typical values are measured at 25°C, but not guaranteed. Output 2nd Order Intercept dBm 75 - *Gain is 0.5 dB less at frequencies higher than 150 MHz Reverse Isolation dB 17 - Input VSWR** --- 1.5:1 1.9:1 Output VSWR** --- 1.5:1 1.9:1 Supply Voltage volts +15 +15 Supply Current mA 235 255 Maximum (No Damage) Ratings Storage Temperature -62°C to +125°C Operating Temperature -55°C to +85°C DC Voltage @ 25°C +17 volts Input Drive @ 25°C (CW) +20 dBm **Input and Output VSWR is 0.2:1 higher at frequencies below 1 MHz. Mechanical & Electrical Parameter Specification Specification Temperatures (Min/Max) -55°C to +85°C Package Size 0.625” Square Gullwing Package Drawing WN Package RF Connectors None Rev Date: 4/15/2014 © API Technologies Corp. Proprietary Information Page # 1 | www.apitech.com | micro.apitech.com | +1.888.553.7531 | [email protected] 4 3 DWG NO. SH 088-00305 1 REV OF 1 P1 1 REVISIONS NOTES: 1. 2. PIN TABLE PIN 3 RF IN PIN 8 RF OUT PIN 10 DC ALL OTHER GROUND CASE GROUND MATERIAL: KOVAR FINISH: NICKEL/GOLD ECN REV. DESCRIPTION CHNG/DATE -- P1 PRELIMINARY RELEASE 2012/05/14 APPVD/DATE CAUTION THIS ASSEMBLY CONTAINS PARTS SENSITIVE TO DAMAGE BY ELECTROSTATIC DISCHARGE (ESD). USE ESD PRECAUTIONARY PROCEDURES WHEN TOUCHING, REMOVING OR INSERTING B B PIN 10 23.75 .935 2.54 .100 TYP. PIN 1 SMI IN PART NO. 3.94 .16 TYP +VDC 2.20 .087 10.16 .400 TYP. OUT DETAIL A SCALE 10 : 1 XXXX 0.38 .015 TYP. REF. DATE CODE 1.28 .050 16 .63 SQ. 0.25 .010 A A 4.06 .16 A SEE SEPARATE PARTS LIST IN ELECTRONIC STORAGE 3rd ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED SPECTRUM MICROWAVE, INC ANSI * INTERPRET DRAWING IAW ASME Y14.100-2004 * DIMENSIONING AND TOLERANCING IAW ASME Y14.5-1994 * PARENTHETICAL INFORMATION FOR REFERENCE ONLY * DIMENSIONAL LIMITS APPLY BEFORE PROCESSES * DIMENSIONS ARE IN INCHES * TOLERANCES ARE: ANGLES ±1.0° * SURFACE FINISH 63 2 PLACE DECIMAL ±.02 3 PLACE DECIMAL ±.005 * REMOVE ALL BURRS AND SHARP EDGES .010 RAD MAX. SPECTRUM MICROWAVE PROPRIETARY INFORMATION THIS DOCUMENT IS THE SOLE PROPERTY OF SPECTRUM MICROWAVE, INC. THE RELEASE OF DATA CONTAINED IN THIS DOCUMENT AND THE REPRODUCTION OF THIS DOCUMENT, IN WHOLE OR IN PART, WITHOUT THE WRITTEN PERMISSION OF SPECTRUM MICROWAVE, INC ARE PROHIBITED. COMPUTER ASSISTED DRAWING GENERATED USING SOLIDWORKS 2007 FORM NO. 1054 SIZE B1 4 3 * CONCENTRICITY MACHINED DIA: .002 FIM * MACHINED TOOL MISMATCH: .002 MAX. DRAWN WAR 2707 Black Lake Place Philadelphia, PA 19154-1008 (USA) DATE 2012/05/14 TITLE OUTLINE DRAWING SG-4 CHECKED ENGRG PH 2012/05/14 MFG SIZE CAGE CODE B 60979 QA SCALE: DO NOT SCALE DRAWING 2 DWG NO. REV 088-00305 SHEET 4:1 1 P1 1 OF 1