RF AMPLIFIER MODEL TM6012PM Available as: Features Typical Intermodulation Performance at 25 ºC Superior Phase Noise Performance High Output Power: +23 dBm Typical High Third Order Intercept: +36 dBm Typical Lower +12 volt Supply Environmental Screening Available Second Order Harmonic Intercept Point ....... +56 dBm (Typ.) Second Order Two Tone Intercept Point ........ +50 dBm (Typ.) Third Order Two Tone Intercept Point ............ +36 dBm (Typ.) (Absolute) Maximum Ratings Specifications CHARACTERISTIC Frequency Gain (dB) Power @ 1 dB Comp. (dBm) Reverse Isolation (dB) VSWR In Out Noise Figure (dB) Power TYPICAL Ta= 25 ºC 5 - 500 MHz 14.5 MIN/MAX Ta = -55 ºC to +85 ºC 5 - 500 MHz 13.0 Min. +23 +20 Min. -18 <1.4:1 <1.2:1 4.6 -15 Max. 2.0:1 Max. 2.0:1 Max. 6.0 Max. +12 88 +12 95 Max. Vdc mA TM6012PM, 4 Pin TO-8 (T4) TN6012PM, 4 Pin Surface Mount (SM3) FP6012PM, 4 Pin Flatpack (FP4) BX6012PM, Connectorized Housing (H1) Ambient Operating Temperature ................ -55ºC to +100 ºC Storage Temperature ................................. -62ºC to +125 ºC Case Temperature .................................................. +125 ºC DC Voltage .......................................................... +15 Volts Continuous RF Input Power .................................. +13 dBm Short Term RF Input Power ............. 50 mW (1 Minute Max.) Maximum Peak Power .................... 0.5 Watt (3 µsec Max.) MTBF Calculation for Ground Benign Environment @ 25 ºC .................................................3,721,883.58 hrs Guaranteed @ 25 ºC Phase Noise Performance (dBc/Hz) Note: Care should always be taken to effectively ground the case of each unit. Frequency 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz Typical -160 -175 -177 -180 -180 Guaranteed -152 -168 -172 -172 -172 Typical Performance Data Gain (dB) 16 15 0 14 - 10 13 - 20 12 Start 5 MHz +24 Stop 500 MHz 1 dB Comp. (dBm) - 30 +23 7 6 +22 5 +21 4 +20 Start 3 5 MHz 2.0 Input VSWR Stop 500 MHz -150 Start 5 MHz Stop 500 MHz Noise Figure (dB) Legend Stop 500 MHz +25 ºC -160 -170 -180 -190 100 Start 5 MHz Output VSWR Stop 500 MHz 1.0 Start 1k 10 k 100 k 1M __ __ __ __Typical Phase Noise Test Conditions * Residual Carrier Frequency: 500 MHz Power Output: +23 dBm 1.5 5 MHz Phase Noise (dBc/Hz) -130 -140 2.0 1.5 1.0 Start Reverse Isolation (dB) + 10 Temperature: 25 ºC Agilent ES5500 System 5 MHz Stop 500 MHz +85 ºC - - - - - - -55 ºC Linear S-Parameters – – – – S12– – – – FREQ. – – – – S11– – – – – – – – S21– – – – – – – – S22– – – Mag MHz Deg Mag Deg Mag Deg Mag Deg ====================================================================================== 5 .23 -41 5.86 -163 .08 19 86 .27 100 .13 80 5.46 159 .11 3 23 .05 200 .40 24 5.51 137 .12 3 23 .04 300 .58 -31 5.50 114 .14 2 45 .04 400 .10 -91 5.53 90 .15 -1 71 .08 500 .20 -137 5.45 64 .17 -9 66 .17 Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532 Rev. 4/09/09 www.SpectrumMicrowave.com Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH (215) 464-4000 · Fax (215) 464-4001