PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED Ordering Guide Model Name MPA1948A MPA1948B MPA1948C MPA1948D MPA1948E Constant current power supply Max current(±5%） Output voltage range 30～50V 700mA 30～50V 600mA 30～50V 500mA 30～50V 425mA 540mA 30～50V RoHS-Y（B) Input Characteristics:（Ta=25℃） Input Voltage Operating Range Input Frequency Inrush Current AC100V（25℃ Cold start） AC242V（25℃ Cold start） Model Name Input current(Typ) Power Factor (Typ) At max current At max current Output Voltage：５０V Output Voltage：５０V AC90V AC267V AC100V AC242V MPA1948A 0.49A 0.18A 0.994 0.939 MPA1948B 0.42A 0.16A 0.991 0.916 MPA1948C 0.35A 0.14A 0.989 0.887 MPA1948D 0.30A 0.13A 0.983 0.853 MPA1948E 0.39A 0.15A 0.988 0.894 Non-communication state Stand-by Power Min 90 47 Typ 100/242 50/60 Max Units 267 Vac 63 Hz 10 A 20 A Input rated capacity Input Power(Typ) At max current Output Voltage：５０V Output Voltage：５０V AC100V AC242V 43.2W 42.2W 40VA 37.0W 36.4W 38VA 31.1W 31.0W 33VA 31VA 26.5W 26.8W 35VA 33.2W 32.9W AC100V：0.13Wｔｙｐ, AC242V：0.23Wｔｙｐ Output Characteristics(*1)：（Ta=25℃） Efficiency（Typ） At max current Output current（±5%) Model Name Ripple current（p-p） Output voltage：30V Average current(Typ) Output voltage：50V Typ（At max current） AC100V Min（*2） Max AC242V AC100V AC242V MPA1948A 77.9% 77.3% 81.8% 83.8% 7～35mA 700mA 108mA MPA1948B 76.8% 76.2% 80.9% 82.5% 6～30mA 600mA 102mA MPA1948C 76.2% 75.1% 81.1% 81.4% 5～25mA 500mA 81mA 4.2～21mA 75.3% 72.6% 80.7% 79.6% MPA1948D 425mA 79mA 76.8% 76.1% 81.3% 82.1% 5.4～27mA MPA1948E 540mA 100mA (*1)Output ( ) p characteristics are measured byy LE-5150-2(KEISOKUGIKEN) ( ) as a LED-load . (*2）Depend on Dimming method. Max current value×(1～5%） Environmental Characteristics: Condition Min Max Typ Units 50 -10 (*) ℃ Operating Temp. Range Non-condensing 5 95 Operating Humidity % -20 55 ℃ Storage Temp. Range Natural air cooling Cooling condition EIAJ RCR-9102B 10 year MTBF Ta=50℃, Max Voltage/Max load 50000 hour Estimated life 480 g Weight Vibration frequency：10～55Hz、Vibration acceleration：2G Sinusoidal Vibration 10G Shock compliant RoHS 1 Year Warranty China Manufacturing Country （*）Start-up at -20℃ Safety: Safety standards Harmonics Conducted emission Insulation resistance Withstand voltage Leakage current Electrical Appliance Safety Low (1st clause) EN61347-1, EN61347-2-13（CB REPORT) EN61000-3-2 class C PSE（1st clause)、EN55015 CLASS B, EN55022 CLASS B 30MΩ or more （Input to Output-Reinforced、Input to Chassis-Basic） AC4000V （60Hz Primary-Secondary）、Leak current：10mA or less AC1600V （60Hz Primary-FG）、Leak current：10mA or less 1 rms or less （AC242V 60Hz normal temperature/normal humidity) Protection Characteristics: Return method Operating Conditions Over Current Protection AC re-input（*） 0.8A or more Latching Over Voltage Protection Auto recovery（**） 60V or more ON/OFF Repeat － ON/OFF Repeat Output Open Protection Auto recovery（**） （*）Input AC again 10 seconds later. （**）When LED is connected, be careful to be possible to flow rush current to LED. Immunity: IEC61000-4-2 Level 3 Electrostatic discharge IEC61000-4-4 Level 3 Electrical fast transient burst IEC61000-4-5 Level 3 Surge Product specification MPA1948 Series 1/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED Mechanical Dimensions・Label Tolerance of outline Range of dimension ０．５ ＜ L ≦ ６ ６ ＜ L ≦ １０ １０ ＜ L ≦ ５０ １０ ＜ L ≦ ５０ ５０ ＜ L ≦ １８０ １８０ ＜ L ≦ ５００ ５００ ＜ L ≦ １０００ L：Dimension Unit：mm LABEL1 Tolerance ± ０．３ ± ０．４ ± ０ ７ ± ０．７ ± １．０ ± １．５ ± ２．０ （Ex．MPA1948A） Product specification MPA1948 Series 2/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED Input/Output Terminal AC Input wire Parts Name CN1 ２３５－５０３/３４２－３２５ （WAGO） Output Connector Connector No. CN１01 CN301 Terminal No. 1 2 3 Description AC Neutral AC LIVE FG Description Terminal No. 1 LED Output－ （Cathode） 2 ２３５－１０４/３３０－０００ LED Output－ （Cathode） （WAGO） 3 LED Output+ （Anode） 4 LED Output+ （Anode） ＊ Terminal 1 and 2 are same voltage. Terminal 3 and 4 are same voltage. Signal Connector Connector No. CN201 Maker Type Name Maker Type Name Maker Type Name B4B-PH-K-S （JST） ２３５－１０２/３３０－０００ （WAGO) ＊CN301 No polarity Terminal No. 1 2 3 4 1 2 Description 3.3V UART_RX（Reception） UART_TX（Transmission） GND DALI or PWM SIGNAL DALI or PWM SIGNAL Instruction for Connecting Conductor ■ Structure : Part name and structure of terminal block. Product specification MPA1948 Series 3/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED ■ Stripping of Wire Please strip a conductor's stripped length related as drawings. Please fix splayed, bent or twisted wire. ■ Connecting Please follow the instructions ① Insert a wire to the wire hole. ② A wire must be inserted to a stop p position. ③ Pull a wire slightly to check if connectingg has been done completely. ■ Removal Please follow the instructions ① Put a screwdriver to the operating slot. ② Hold down a screwdriver, a conductor can be releaase Product specification MPA1948 Series ③ Put off a screwdriver. 4/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED 【Dimming Specifications】 This product supports UART, DALI and PWM mode. In the case of UART, DALI and PWM Dimming mode, change a dip switch (SW401) to each mode before AC input. (Refer as follows) Dimming Input Connector UART CN201 DALI CN301 PWM CN301 Communication standard・Dimming Specifications IEEE802.15.4Product Description SW401 posision：DALI side （Use a Murata special module about UART.） IEC62386 SW401 posision：DALI side Input pulse 10-16Vo-p Frequency 100Hz－1KHz DUTY 0－95%typ Ex.） Output current：Duty 0%・・・700mA、95%・・・OFF、f:1KHz Output current：Duty 0%・・・700mA、 98%・・・OFF、f:100Hz SW401 posision：PWM side Di i characteristics（Masterpiece） Dimming h i i （M i ） LOGARITHM 1 9 17 25 33 41 49 57 65 73 81 89 97 105 113 121 129 137 145 153 161 169 177 185 193 201 209 217 225 233 241 249 Io( Io(mA） UART-Dimming curve 800 700 600 500 400 300 200 100 0 STEP（1～254） LINEAR LOGARITHM 1 9 17 25 33 41 49 57 65 73 81 89 97 105 1 113 1 121 1 129 1 137 1 145 1 153 1 161 1 169 1 177 1 185 1 193 1 201 2 209 2 217 2 225 2 233 2 241 2 249 2 Io(mA) DALI-Dimming curve 800 700 600 500 400 300 200 100 0 STEP（1～254） Io(m Io(mA） PWM-Dimming curve 800 700 600 500 400 300 200 100 0 PWM:100Hz PWM:1kHz 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 PWM-Duty（%） Product specification MPA1948 Series 5/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED 【Instruction Manual】 Before using the Power Supply Unit Pay attention to all warnings and cautions before using the PSU. Incorrect usage could lead to an electrical shock, damage to the PSU or a fire hazard. ★Warning & Caution ・Do not modify and remove the cover. ・If any failure or trouble occurs because of utilizing the power supply unit without reflecting the described contents on this specification, Murata cannot assure such trouble. ・Do not touch the internal components, they may have high voltage or high temperature. You may get electrical shock or burned. ・Definitely avoid to use the power supply unit by the excessive input voltage, output voltage, output current and ambient temperature as defined on this specification. The excessive current, voltage and temperature will cause the deterioration of the components or abnormal heat, both of which may affect not only to shorten the unit's life-long but also to damage and break the unit. In a case of LED VF 30V or less because of LED chip dispersion, please make sure to evaluate and confirm the quality upon mounting the power supply unit to your product. But don't use it under the LED VF 25V or less. ・Use the PSU after confirm the correct connection of input and output. ・Be sure not to scratch and damage the input leads. Never transfer the unit by holding and pulling any lead wire. ・If If PSU iis ddropped, d absolutely b l t l nott tto use it any more. ・Make sure not to install and/or store the unit under the environment as stated below because such will cause the insulation deterioration. ① Make sure to avoid storing the unit under the condition of high temperature, high humidity or direct sunlight which are out of the standard on this specification. ② Ambient air containing the corrosive gas. (Cl2, H2S, NH3, SO2, NOX, etc.) ③ Places which have the fear to be splashed with water, oil, organic solvent, etc. ④ Places with a high concentration of dusty places. ⑤ Other environment correspondingly mentioned above. ・Make sure not to install and/or store the unit under the environment as stated below because such will cause the insulation deterioration. ① If any alien substance attached on terminals, it may cause the contact failure or insertion deterioration. ② The use of the silicon rubber or silicon bond which contain a high percentage of dimethylpolysiloxane may cause to trigger the contact failure of volume, potentiometer volume or switch. Make sure to use such rubber or bond with the percentage of dimethylpolysiloxane 0.1% or less. ・PSU can not be used under the condition of the series operation. ・Rust may occur in the chassis because of use environment. ・This specification regulates the quality of the power unit, if nothing specially defined. When using the power supply unit, make sure to evaluate and confirm the quality upon mounting the power supply unit to your product. Product specification MPA1948 Series 6/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED 【Mounting】 Mounting method ・Please use the place at 50℃ or less around the PSU ambient. ・Please connect the thick and short wire to the FG terminal for safety and EMI. ・Please separate Input wire and Output wire surely. ・Please refer as follows about the recommended Wire for input, output and dimming. AC-intput wire：φ0.8-1.6mm，0.5-2.5m㎡ single wire （Strip length 9-10mm) LED Output wire/Dimming wire for DALI and PWM： φ0.8-1.2mm，0.5-1.5m㎡ single wire （Strip length 9-10mm) ・Please fix a screw about the installation of the power supply more than one place of one side. (more than two places in total) （Screw hole：φ3.5×4、Φ4.5×2） 【Parallel Operation】 ・Series Operation is not possible. ・For parallel operation, either method (1) or (2) is possible. But please caution as follows. *）PSU *）PSU output [＋] and [＋] are connected in PSU. PSU [－] are the same. same Therefore this PSU are not 2 output. Parallel 1：In a case of operating the plural LEDs for one power supply. If LED Vf voltage are different, the current may be partial. Please add a balance circuit not to become so. PSU Output Terminal ＋ ＋ － － LED Load LED Load Parallel 2：In a case of operating twe Power supplies for one LED. The total current of two power supplies pass through in the LED. And please confirm the leakage current as the system. ＋ PSU Output ＋ Terminal － － LED Load PSU ＋ Output ＋ Terminal － － Product specification MPA1948 Series 7/8 PRODUCT SPECIFICATION MPA1948 Series Power Supply for LED PACKING SPECIFICATION Use for the Model MPA1948 series. PARTS NAME NO. Q'TY 1 PACKING BOX 1/12 2 BASE PAD 2/12 3 PARTITION BOARD 1/12 4 Small PE Bag 12/12 PACKING PROCESS : Note: 1. It contains 12 pieces of product in every box. (2) CN101 is on the top (4) Label Side (3) (2) (1) 300mm 320mm 400mm ACH29 Figture.1 Product specification MPA1948 Series 8/8