PRODUCT SPECIFICATION MPA1967 series Power Supply for LED Ordering Guide Model Name MPA1967A MPA1967B MPA1967C Constant current power supply Max current(±5%) Output voltage range 8~25V 1050mA 8~25V 900mA 750mA 8~25V RoHS-Y(B) Input Characteristics:(Ta=25℃) Input Voltage Operating Range Input Frequency Inrush Current AC100V(25℃ Cold start) AC242V(25℃ Cold start) 品名 Input current(Typ) Power Factor (Typ) At max current At max current Output Voltage:25V Output Voltage:25V AC267V AC100V AC90V AC242V 0.37A 0.14A 0.9948 0.900 MPA1967A 0.31A 0.13A 0.9936 0.866 MPA1967B 0.26A 0.11A 0.9877 0.822 MPA1967C Non-communication state Stand-by Power Min 90 47 Typ 100/242 50/60 Max Units 267 Vac 63 Hz 10 A 20 A Input rated capacity Input Power(Typ) At max current Output Voltage:25V Output Voltage:25V AC100V AC242V 33VA 32.7W 32.2W 31VA 27.7W 27.8W 25VA 23.1W 23.5W AC100V:0.13Wtyp, AC242V:0.23Wtyp Output Characteristics(*1):(Ta=25℃) Output current(±5%) Efficiency(Typ) At max current Model Name Average current(Typ) Ripple current(p-p) Output voltage:8V Output voltage:25V Typ(At max current) AC100V Min(*2) Max AC242V AC100V AC242V 73.4% 72.5% 80.6% 82.0% MPA1967A 11~53mA 1050mA 140mA 73.2% 71.8% 81.2% 81.1% MPA1967B 9~45mA 900mA 120mA 72.5% 70.3% 81.7% 80.1% MPA1967C 8~38mA 750mA 100mA (*1)Output characteristics are measured by LE-5150-2(KEISOKUGIKEN) as a LED-load . (*2)Depend on Dimming method. Max current value×(1~5%) Environmental Characteristics: Condition Min Max Typ Units 50 Operating Temp. Range -10 (*) ℃ Non-condensing 5 95 % Operating Humidity 55 ℃ 20 -20 St r Storage Temp. T Range R n Natural air cooling Cooling condition EIAJ RCR-9102B year 10 MTBF Ta=50℃, Max Voltage/Max load hour 50000 Estimated life g 470 Weight Vibration frequency:10~55Hz、Vibration acceleration:2G Sinusoidal Vibration 10G Shock compliant RoHS 1 Year Warranty China Manufacturing Country (*)Start-up at -20℃ Safety: Safety standards Harmonics Conducted emission Insulation resistance Withstand voltage Leakage current Electrical Appliance Safety Low (1st clause) EN61347-1, EN61347-2-13(CB REPORT):planning EN61000-3-2 class C PSE(1st clause)、EN55015 CLASS B, EN55022 CLASS B 30MΩ or more (Input to Output-Reinforced、Input to Chassis-Basic) AC4000V (60Hz Primary-Secondary)、Leak current:10mA or less AC1600V (60Hz Primary-FG)、Leak current:10mA or less 0.5 rms or less (AC242V 60Hz normal temperature/normal humidity) Protection Characteristics: Return method Output shortn Protection Auto recovery(*) Auto recovery(*) Output Open Protection (*)It's need about 10 seconds at the autorecovery. When LED is connected, be careful to be possible to flow rush current to LED. AC re-input as much as possible. Immunity: Electrostatic discharge Electrical fast transient burst Surge IEC61000-4-2 IEC61000-4-4 IEC61000-4-5 Product specification MPA1967 series Level 3 Level 3 Level 3 1/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED Mechanical Dimensions・Label Unit:mm LABEL1 (Ex.MPA1967A) Product specification MPA1967 series 2/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED Input/Output Terminal AC Input wire Maker Type Name Parts Name CN1 235-503/342-325 (WAGO) Output Connector Connector No. CN101 Signal Connector Connector No. CN201 CN401 CN402 Maker Type Name 235-102/330-000 Terminal No. 1 2 3 Description AC Neutral AC LIVE FG Terminal No. 1 2 Description LED 出力- (カソード) LED 出力+ (アノード) Maker Type Name Terminal No. 1 2 B4B-PH-K-S (JST) 3 4 1 250-202 (WAGO) 2 1 250-202 (WAGO) 2 *CN401、CN402 No polarity. One is for connections. Description 3.3V Output (200mAmax) UART_RX(Reception) UART_TX(Transmission) GND DALI or PWM SIGNAL DALI or PWM SIGNAL DALI or PWM SIGNAL DALI or PWM SIGNAL Instruction for Connecting Conductor ■ Structure : Part name and structure of terminal block. Product specification MPA1967 series 3/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED ■ Stripping of Wire Please strip a conductor's stripped length related as drawings. Please fix splayed, bent or twisted wire. ■ Connecting Please follow the instructions ① Insert a wire to the wire hole. ② A wire must be inserted to a stop p position. ③ Pull a wire slightly to check if connectingg has been done completely. ■ Removal Please follow the instructions ① Put a screwdriver to the operating slot. ② Hold down a screwdriver, a conductor can be releaase ③ Put off a screwdriver. Product specification MPA1967 series 4/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED 【Dimming Specifications】 This product supports UART, DALI and PWM mode. In the case of UART, DALI and PWM Dimming mode, change a dip switch (SW401) to each mode before f AC C input. (Refer ( f as follows) f ) Dimming Input Connector UART DALI PWM CN201 Communication standard・Dimming Specifications Smart Lighting System UART Command Specification SW401 posision:DALI side (Use a Murata special module about UART.) IEC62386 SW401 posision:DALI side I Input pulse l 10 10-16Vo-p 16V Frequency 100Hz-1KHz DUTY 0-95%typ CN401/CN402 Ex.) Output current:Duty 0%・・・1050mA、95%・・・OFF、f:1KHz Output current:Duty 0%・・・1050mA、 98%・・・OFF、f:100Hz SW401 posision:PWM side PWM sink current:2mAmax *CN401 and CN402 cab be used one, other is for connections. CN401/CN402 Di i characteristics(Masterpiece:MPA1967A) Dimming h t i ti (M t i MPA1967A) DALI/UART dimming curve 1100 1000 900 800 Io(mA) 700 600 LINEAR 500 400 LOGARITHM 300 200 100 1 9 17 25 33 41 49 57 65 73 81 89 97 105 113 121 129 137 145 153 161 169 177 185 193 201 209 217 225 233 241 249 0 STEP(1~254) PWM dimming curve 1100 1000 900 800 Io(mA) 700 600 PWM:100Hz 500 400 PWM:1kHz 300 200 100 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 PWM-Duty(%) Product specification MPA1967 series 5/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED 【Instruction Manual】 Before using the Power Supply Unit Pay attention to all warnings and cautions before using the PSU. Incorrect usage could lead to an electrical shock, damage to the PSU or a fire hazard. ★Warning & Caution ・Do not modify and remove the cover. ・If any failure or trouble occurs because of utilizing the power supply unit without reflecting the described contents on this specification, Murata cannot assure such trouble. ・Do not touch the internal components, they may have high voltage or high temperature. You may get electrical shock or burned. ・Definitely avoid to use the power supply unit by the excessive input voltage, output voltage, output current and ambient temperature as defined on this specification. The excessive current, voltage and temperature will cause the deterioration of the components or abnormal heat, both of which may affect not only to shorten the unit's life-long but also to damage and break the unit. In a case of LED VF 30V or less because of LED chip dispersion, please make sure to evaluate and confirm the quality upon mounting the power supply unit to your product. But don't use it under the LED VF 25V or less. ・Use the PSU after confirm the correct connection of input and output. ・Be sure not to scratch and damage the input leads. Never transfer the unit by holding and pulling any lead wire. ・If If PSU iis ddropped, d absolutely b l t l nott tto use it any more. ・Make sure not to install and/or store the unit under the environment as stated below because such will cause the insulation deterioration. ① Make sure to avoid storing the unit under the condition of high temperature, high humidity or direct sunlight which are out of the standard on this specification. ② Ambient air containing the corrosive gas. (Cl2, H2S, NH3, SO2, NOX, etc.) ③ Places which have the fear to be splashed with water, oil, organic solvent, etc. ④ Places with a high concentration of dusty places. ⑤ Other environment correspondingly mentioned above. ・Make sure not to install and/or store the unit under the environment as stated below because such will cause the insulation deterioration. ① If any alien substance attached on terminals, it may cause the contact failure or insertion deterioration. ② The use of the silicon rubber or silicon bond which contain a high percentage of dimethylpolysiloxane may cause to trigger the contact failure of volume, potentiometer volume or switch. Make sure to use such rubber or bond with the percentage of dimethylpolysiloxane 0.1% or less. ・PSU can not be used under the condition of the series operation. ・Rust may occur in the chassis because of use environment. ・This specification regulates the quality of the power unit, if nothing specially defined. When using the power supply unit, make sure to evaluate and confirm the quality upon mounting the power supply unit to your product. Product specification MPA1967 series 6/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED 【Mounting】 Mounting method ・Please use the place at 50℃ or less around the PSU ambient. ・Please connect the thick and short wire to the FG terminal for safety and EMI. ・Please separate Input wire and Output wire surely. ・Please refer as follows about the recommended Wire for input, output and dimming. AC-intput wire:φ0.8-1.6mm,0.5-2.5m㎡ single wire (Strip length 9-10mm) LED Output wire/Dimming wire for DALI and PWM: φ0.8-1.2mm,0.5-1.5m㎡ single wire (Strip length 9-10mm) ・Please fix a screw about the installation of the power supply more than one place of one side. (more than two places in total) (Screw hole:φ3.5×4、Φ4.5×2) 【Parallel Operation】 ・Series Operation is not possible. ・For parallel operation, either method (1) or (2) is possible. But please caution as follows. Parallel :In a case of operating twe Power supplies for one LED. The total current of two power supplies pass through in the LED. And please confirm the leakage current as the system. PSU + Output Terminal - LED Load PSU + Output Terminal - Product specification MPA1967 series 7/8 PRODUCT SPECIFICATION MPA1967 series Power Supply for LED PACKING SPECIFICATION Use for the Model MPA1967A/MPA1967B/MPA1967C series. NO. 1 2 3 4 PARTS NAME PACKING BOX BASE PAD PARTITION BOARD Small PE Bag Q'TY 1/12 2/12 1/12 12/12 PACKING PROCESS : Note: 1. It contains 12 pieces of product in every box. (2) (4) CN101 is on the top (3) (2) 300mm (1) 320mm 400mm Figture.1 ACH29 Product specification MPA1967 series 8/8