S-Series Datasheet [pdf]

S-Series
S-Series
ROCKER SWITCHES
S-Series rocker switches are designed for use in the enclosed cabs of today’s trucks, with special focus
afforded to the vehicle operator. With features including abbreviated travel ½ throw actuation, ergonomic
rockers, illumination in up to three detent switch positions, and a non-teasable snap action circuit,
these switches provide the driver with easily recognizable and simple to operate controls. Designers will
appreciate the 10A, 24VDC rating, space saving compact envelope, clean bezel-less design, integrated
low insertion force connector and polarized switch base for quick installation. Most any illumination and
switch circuitry is easily accommodated with the S-Series 10 terminal base.
Product Highlights:
Abbreviated travel ½ throw actuation
Ergonomic rockers
ŠŠ Recognizable and simple to operate controls
ŠŠ Compact Design
Typical Applications:
On-Highway Transportation Equipment
Agricultural Equipment
ŠŠ Construction Equipment
ŠŠ Marine
ŠŠ
ŠŠ
ŠŠ
ŠŠ
Carling Technologies, Inc.
60 Johnson Avenue, Plainville, CT 06062
Email: [email protected]
Application Support: [email protected]
Phone: 860.793.9281 Fax: 860.793.9231
www.carlingtech.com
2 | S-Series Rocker Switches - General Specifications
Electrical
Contact Rating
[email protected] 24VDC
Dielectric Strength
1500 Volts RMS between pole to
pole
Insulation Resistance
50 Megaohms
Contact Resistance
10 milliohms max. @ 4VDC
Contact Bounce
<20 milliseconds
Life 100,000 cycles maintained circuit,50,000 cycles momentary circuit at rated voltage and current gold plated
Circuitry
SP, DP 2 & 3 position,
1/2 or full throw
Terminals
.110 Tabs, Silver Plated Brass
Mechanical
Endurance
250,000 cycles minimum
Physical
Lighted
LED - rated 100,000 hours 1/2 life (LED is internally ballasted for voltages to 24VDC.)
BracketAcetal
Base
Nylon 66 GF
RockerPolycarbonate
Weight
25 gms max.
Environmental
Operating Temperature -40°C to +85°C
Vibration
Per IEC 68-2.6 test Fc and 68-2.47 Test Criteria - no noise or contact chatter below 10ms.
Cold Test
Per IEC 68-2-1 -40°C for 72 hours
Test Criteria - pre & post test contact resistance.
Dry Heat Test Criteria Per IEC 68-2-2 + 85°C for 72 hours
Test Criteria - no loss of circuit during test, pre & post test contact resistance.
Handling Shock
Drop from height of 1 meter, 3
times,
4 sides. Test criteria - No loss of circuit during test, pre & post test contact resistance.
Thermal Shock
Per IEC 68-2-14, -40°C to +85°C.
Test criteria - pre & post test contact
resistance.
Mounting Specifications
Snap in Mount
40mm x 20mm keyed hole (see dimensional specifications for details.)
Connector
Amp/Tyco MCP 2.8 receptacle housing P/N 1418994-1
mates with Amp/Tyco MCP 2.8 flat type receptacle. Based
on wire size, choose P/N below:
1-968880-1
1-968849-1
1-968851-1
20-24 awg wire
17-20 awg wire
13.5-17 awg wire
Actuator Travel (Angular Displacement)
2 position (1/2 throw)
3 position (full throw)
12°
12° from center
*Manufacturer reserves the right to change product specification without prior notice.
Email: [email protected] Application Support: [email protected]
Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com
| 3
S-Series Rocker Switches - Ordering Scheme
S 18 A A R F 0 4
1
Series
2
Circuit
3
Rating
4
5
Illumination Lamp 1
6
Lamp 2
7
Lamp 3
8
Bracket
Color
( ) - momentary
SP - single pole uses terminals
DP - double pole uses terminals
2
Connected Terminals OFF OFF 3
3 & 5, 4 & 6
ON
(ON)
4, 5, 6, 7 OFF OFF 3&5
3&5
OFF 5&7
5&7
5 & 7, 4 & 6 5 & 7, 4 & 6 OFF
NONE 1
NONE 1
NONE 1
NONE 1
ON
ON
(ON)
(3 & 5, 4 & 6)
(5 & 9, 4 & 6)
3 RATING
1
0.4VA 28VDC Resistive
A 3 10.5mA 1.5A 28VDC,
5A 28V 50A Inrush Lamp Load
B 4 3.5A 28VDC, 18A Inrush
3
C 10mA 10A 28VDC
D 3 20mA 10A 14VDC
4 ILLUMINATION
Lamps
S
NONE A
1
C
1
2
D
1
2
E
1&3
F
1
G
1&2
H
1&2
J
1, 2 & 3 K
1&2
9
Actuator
Color
10
Legend
Color 1
11
Legend
Color 2
12
Legend
Color 3
13
Legend 1
1 00 00
15
14
Legend 2
Legend
Orientation
16
Legend 3
5,6,7 LAMP (SAME CODING FOR ALL 3 SELECTIONS)
Selection 5: specifies lamp 1 located above terminals 1 (+) & 2 (-).
Selection 6: specifies lamp 2 located in center of rocker.
Selection 7: specifies lamp 3 located above terminals 9 (+) & 10 (-).
1 SERIES
S
2 CIRCUIT
Terminal Connections as viewed
from bottom of switch:
1 - - 2
3, 5 & 7.
3 - - 4
3, 5, 7 & 4, 6, 8.
5--6
7--8
9 - - 10
Position: 1
SP DP 5 & 7, 6 & 8 16 26 ON 18 28 (ON) SPECIAL CIRCUITS
31 (6 & 8) 41 51 ON 42 52 (ON) 43 53 (ON) 44 54 ON 45 55 (ON) 46 56 NONE 47 57 NONE 75 (5 & 7, 3 & 6) 2
98 (5 & 7, 2 & 6) M Z Z Z 00
No lamp LED 12VDC 24VDC 0
Red A
B
Green
H
J
8 BRACKET COLOR
1
Black
4
Dark Carbon
9 ACTUATOR
Standard Rocker, Laser Etched
Black Titan Gray M
N
Dark Carbon
R
10, 11, 12 LEGEND COLOR
Z
No Legend
1
Clear
13 LEGEND 1 5
00
No Legend
ORIENTATION
1
14 LEGEND ORIENTATION
0
No legend
1
Orientation 1
2
Orientation 2
3
Orientation 3
4
Orientation 4
M22ZA8-13H-10000
M22ZA8-23H-10000
Illumination Type Lamp wired to Terminals
INDEPENDENT –
INDEPENDENT 1 (+) 2 (–)
INDEPENDENT 1 (+) 2 (–)
INDEPENDENT 9 (+) 2 (–)
INDEPENDENT 1 (+) 2 (–)
INDEPENDENT
9 (+) 10 (–)
INDEPENDENT 1 (+) 2 (–)
PARALLEL
INDEPENDENT 1 (+) 10 (–)
SNAP
INDEPENDENT 1 (+) 10 (–)
DEPENDENT 9 (+) 2 (–)
INDEPENDENT 1 (+) 2 (–)
DEPENDENT 9 (+) 10 (–)
INDEPENDENT
1 (+) 2 (–)
DEPENDENT 5 (+) 10 (–)
INDEPENDENT 1 (+) 2 (–)
INDEPENDENT 1 (+) 2 (–)
INDEPENDENT 9 (+) 10 (–)
3.3K RESISTOR IN PARALLEL
Orange Yellow C
E
D
F
ORIENTATION
4
ORIENTATION
2
ORIENTATION
3
15,16 LEGEND 2,3 6
00 No legend
Notes:
1 Indicates 1/2 travel for actuator.
2 Snap-Action Contact Mechanism
3 Not available with circuit 98.
4 Available with circuit 98 only.
5 Located over T1-2.
6 Legend 2 located in center of rocker, Legend 3 located over T9-10.
Legend 2 options are limited due to a very small marking area.
Consult factory for specifics.
Email: [email protected] Application Support: [email protected]
Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com
4 | S-Series Rocker Switches - Dimensional Specifications
Dimensional Specifications: in. [mm]
MATES WITH TYCO/AMP MCP CONNECTOR 1418994-1
1.529
[38.84]
.787
[19.99]
.83
[21.1]
.100
[2.54]
PANEL KEY
.048
[1.22]
.032
[.81]
1.575
[40.01]
PANEL THICKNESS: 2.5±0.1mm
PANEL OPENING CLEARANCE: ±5°
SCALE 2.000
POS 0
POS 2
POS 1
R.833±.015
[21.15±0.38]
SWING RADIUS
.220
[5.59]
12°
12°
.82
[20.8]
.790
[20.07]
1.23
[31.2]
1.60
[40.6]
.79
[20.1]
Email: [email protected] Application Support: [email protected]
Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com
R.016
[.41]
(8 PLACES)
R.079
[2.01]
(4 PLACES)
Reps & Contact | 5
Authorized Sales Representatives
Click on the group name on the map below to find your local representative or visit
www.carlingtech.com/findarep.
«
«
Matera
W. Canada
Matera
E. Canada
MIDWEST
DM
Michigan
TEMCO Northwest
Alaska, Hawaii
«
NORTHERN
Hanna Lind Ltd.
Melody
Emery
Sierra
Bridge Marketing
Omega Limited
Dy-tronix Inc.
LD. Allen
Norris
DM Assoc
East
Pacent
DM
Assoc
TSI North
TSI
WEST
Signal
Enterprises
Luscombe
Engineering
Pinnacle Marketing
Matrix
DM Mexico
South America
Mexico
«
«
Sunbelt Components
SOUTHEAST
ProRep
Solutions
LATIN AMERICA
Americas
Europe
Middle East
Africa
Asia-Pacific
Oceania
About Carling
Founded in 1920, Carling Technologies is a leading manufacturer of electrical and electronic switches
and assemblies, circuit breakers, electronic controls, power distribution units, and multiplexed power
distribution systems. With four ISO registered manufacturing facilities and technical sales offices worldwide,
Carling Technologies Sales, Service and Engineering teams do much more than manufacture electrical
components, they engineer powerful solutions! To learn more about Carling please visit
www.carlingtech.com/company-profile.
To view all of Carling’s environmental, quality, health & safety certifications please visit
www.carlingtech.com/environmental-certifications
Email: [email protected] Application Support: [email protected]
Phone: (860) 793–9281 Fax: (860) 793–9231 www.carlingtech.com
Worldwide Headquarters
Carling Technologies, Inc.
60 Johnson Avenue, Plainville, CT 06062
Phone: 860.793.9281 Fax: 860.793.9231
Email: [email protected]
Northern Region Sales Office: [email protected]
Southeast Region Sales Office: [email protected]
Midwest Region Sales Office: [email protected]
West Region Sales Office: [email protected]
Latin America Sales Office: [email protected]
Asia-Pacific Headquarters
Carling Technologies, Asia-Pacific Ltd.,
Kowloon, Hong Kong
Phone: Int + 852-2737-2277 Fax: Int + 852-2736-9332
Email: [email protected]
Shenzhen, China: [email protected]
Shanghai, China: [email protected]
Pune, India: [email protected]
Kaohsiung, Taiwan: [email protected]
Yokohama, Japan: [email protected]
Europe | Middle East | Africa Headquarters
Carling Technologies LTD
4 Airport Business Park, Exeter Airport,
Clyst Honiton, Exeter, Devon, EX5 2UL, UK
Phone: Int + 44 1392.364422 Fax: Int + 44 1392.364477
Email: [email protected]
Germany: [email protected]
France: [email protected]
www.carlingtech.com
REV_12_2015