Packaging and Order Information www.vishay.com Vishay Semiconductors Packaging and Order Information PACKAGING SURVEY RECOMMENDED METHOD OF STORAGE Dry box storage is recommended as soon as the dry bag has been opened to prevent moisture absorption. TABLE 1 - PACKAGING OPTIONS OF DETECTOR AND EMITTER DEVICES PACKAGING OPTION PACKAGE FORM SERIES Metal can BPW./TS. BULK TAPE BLISTER TAPE TEKS5400S TEKT5400S TSKS5400S X X X TEM./TSM./ VEM./VSM. Other leaded packages X L E V E L BP104 BPW34 Top view mold CAUTION X X BP./TE./TS. X 2a This bag contains MOISTURE –SENSITIVE DEVICES BP104S BPW34S 1. Shelf life in sealed bag 12 months at <40°C and < 90% relative humidity (RH) 2. After this bag is opened devices that will be subjected to infrared reflow, vapor-phase reflow, or equivalent processing (peak package body temp. 260°C) must be: a) Mounted within 672 hours at factory condition of < 30°C/60%RH or b) Stored at <10% RH. X MOISTURE PROOF PACKAGING The reel is packed in a moisture proof aluminum bag to protect devices from absorbing moisture during transportation and storage. Aluminum bag • Storage humidity ≤ 60 % RH max. After storage longer than the specified floor life (see table 2), moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to their former condition by drying using conditions according to the individual moisture sensitivity level (MSL) specified on a sticker affixed to the dry bags (e.g. figure 2, MSL 2a). X TSKS542.X01 SMD • Storage temperature 10 °C to 30 °C TUBE X TEKS5400. Side view lens The following conditions should be observed if dry boxes are not available: Moisture level sticker Bar code ESD sticker label 3. Devices require baking before mounting if: a) Humidity Indicator Card is >10% when read at 23°C + 5°C or b) 2a or 2b is not met. 4. If baking is required, devices may be baked for: 192 hours at 40°C + 5°C/-0°C and <5%RH (dry air/nitrogen) or o or 96 hours at 60±5 Cand <5%RH For all device containers 24 hours at 100±5°C Not suitable for reels or tubes Bag Seal Date: ______________________________ (If blank, see bar code label) Note: LEVEL defined by EIA JEDEC Standard JESD22-A113 19786 Fig. 2 - Example of MSL Sticker TABLE 2 - MOISTURE SENSITIVITY LEVEL, FLOOR LIFE AND FLOOR CONDITIONS Box 0 Reel 18298 Fig. 1 - Moisture Proof Packaging Rev. 1.5, 02-Mar-15 MSL FLOOR LIFE CONDITIONS 1 No limit ≤ 30 °C/90 % RH 2 1 year 2a 672 h 3 168 h 4 72 h 5 24h/48 h 6 6h ≤ 30 °C/60 % RH Document Number: 80090 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors TABLE 3 - MOQ/DELIVERY UNIT SURVEY PACKAGE FORM/DEVICE TYPE MINIMUM ORDER QUANTITY DELIVERY UNIT Bulk e.g. TSAL, TSHF, BPV 4000 4000/bulk Tape e.g. TSHF5210-ES21 5000 1000/reel LEADED 5 mm 3 mm Bulk e.g. TSAL, VSLB, TEFT 5000 5000/bulk 10 000 2000/reel Bulk e.g. CQY37N, BPW17N 5000 5000/bulk Tape e.g. CQY37N-CS12 4000 2000/reel Bulk e.g. TSKS, TEKT 2000 2000/bulk Tape e.g. TSKS5400S-ASZ 2000 2000/reel Bulk e.g. TEST2600, TSSS2600 5000 5000/bulk Tape e.g. TEST2600-MS21 5000 1000/reel Bulk e.g. BP104, BPW34 3000 3000/bulk Tube e.g. BP104S 1800 45/tube Bulk e.g. BPV22F, BPW46 4000 4000/bulk Tape e.g. BPV22F-AS12 5000 1000/reel 500 500/bulk 1000 1000/bulk e.g. VSMF3710-GS08 7500 1500/reel e.g. VSMF3710-GS18 8000 8000/reel 3000 3000/reel 3000 3000/reel 1500 1500/reel 1000 1000/reel 2000 2000/reel 6000 6000/reel 3000 3000/reel 1000 1000/reel Tape e.g. VSLB3940-MSZ 1.8 mm Side View Lens Side View Micro Top View Detector Side View Detector Metal Can TO-5 Bulk e.g. BPW21R, BPW20RF Metal Can TO-18 Bulk e.g. BPW76, TSTS7100 SMD PLCC-2 0805 e.g. TEMT6200FX01 1206 e.g. TEMT6000X01 SMD Top View e.g. TEMD5010X01 SMD Gullwing, Reverse Gullwing e.g. VBP104S, VBPW34FASR Little Star e.g. VSMY7850X01 Dome Lens 1.8 mm e.g. VSMB2020X01, VEMD2020X01 Dome Lens 1.8 mm, Side Looker e.g. VSMB2943SLX01, VEMD2023SLX01 Dome Lens 1.9 mm e.g. TSML1020, TEMT1020 Rev. 1.5, 02-Mar-15 Document Number: 80090 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors ESD PRECAUTION TAPING OF SMD Proper storage and handling procedures should be followed to prevent ESD damage to the devices, especially when they are removed from the antistatic shielding bag. Vishay SMD IR emitters and detectors are packed in antistatic blister tapes (in accordance with DIN IEC 40 (CO) 564) for automatic component insertion. The blister tapes are plastic strips with impressed component cavities, which are covered by a glued top tape. BAR CODE LABELS Vishay Semiconductor standard bar code labels are printed on the final package. Labels containing Vishay Semiconductor specific data are affixed to each package unit. Missing Devices A maximum of 0.5 % of the total number of components per reel may be missing, excluding missing components at the beginning and at the end of reel. A maximum of three consecutive components may be missing. This gap is followed by ≥ 6 consecutive components (minimum). De-reeling direction 94 8158 > 160 mm A B C D E F 21379 Fig. 3 - Bar code design and information Tape leader 40 empty compartments min. 75 empty compartments Carrier leader Carrier trailer Fig. 4 - Beginning and End of Reel A) PDF417 bardoce including 325 char B) Plant code according TQD9021 http://intra.hn.vishay.com/quality/docs/tqd/tqd_9021.htm C) Lot1 and Lot2 reflects the lot numbers. Lot2 is a combination of 19 (PTC), 0745 (YYWW), 1 (production day MO=1, TU=2), A (Shift A,B,C) and 01 as production equipment D) Batch contains the datecode 200745 (YYYYWW), origin (PH=Philippines), 19 (PTC) E) Unique label serial number: VO production location (ISO), 01=label station ID, 00001158 (serial number) F) Check digit: counting number starting at A00 up to Z99 to give e.g. a manufactured reel a serial number (track and trace information) Rev. 1.5, 02-Mar-15 Document Number: 80090 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors TAPING SMD PLCC-2 PACKAGE TAPING STANDARDS GS08 AND GS18 GS08: 1500 pcs/reel GS18: 8000 pcs/reel The tape leader is at least 160 mm and is followed by a carrier tape leader with at least 40 empty compartments (figure 3). The tape leader may include carrier tape as long as the cover tape is not connected to carrier tape. Adhesive tape The last component is followed by a carrier tape trailer with at least 75 empty compartments, sealed with cover tape. Blister tape 10.0 9.0 120° Component cavity 4.5 3.5 94 8670 2.5 1.5 Fig. 5 - Blister Tape 3.5 3.1 2.2 2.0 5.75 5.25 3.6 3.4 4.0 3.6 Identification Label: Vishay type group tape code production code quantity 13.00 12.75 63.5 60.5 14.4 max. 180 178 94 8665 8.3 7.7 Fig. 7 - Reel Dimensions: GS08 1.85 1.65 1.6 1.4 4.1 3.9 4.1 3.9 0.25 2.05 1.95 10.4 8.4 120° 94 8668 Fig. 6 - Tape Dimensions in mm for PLCC-2 4.5 3.5 13.00 12.75 2.5 1.5 Identification Label: Vishay type group tape code production code quantity 62.5 60.0 321 329 14.4 max. 18857 Fig. 8 - Reel Dimensions: GS18 COVER TAPE REMOVAL FORCE The removal force may vary in strength between 0.1 N and 1.0 N at a removal speed of 5 mm/s. In order to prevent components from popping out of blisters, the cover tape must be pulled off at an angle of 180° relative to the feed direction. Rev. 1.5, 02-Mar-15 Document Number: 80090 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors TAPING SMD WITH PCB OR DOME PACKAGE Dimensions in millimeters 20874 Fig. 9 - Reel of TEMD5010X01, TEMD5020X01, TEMD5110X01, TEMD5120X01, and TEMD5510FX01 20537 Fig. 10 - Blister Tape of TEMD5010X01, TEMD5020X01, TEMD5110X01, TEMD5120X01, and TEMD5510FX01 Rev. 1.5, 02-Mar-15 Document Number: 80090 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 21732 Fig. 11 - Reel of VBP104S, VPB104SR Series and VBPW34S, VBPW34SR Series 21730 Fig. 12 - Blister Tape VBP104S Series and VBPW34S Series Rev. 1.5, 02-Mar-15 Document Number: 80090 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 21731 Fig. 13 - Blister Tape VBP104SR Series and VBPW34SR Series Unreel direction X 2. Ø 62 ± 0.5 Reel Ø 13 ± 0.5 Ø 330 ± 1 0.5 5± Tape position coming out from reel 6000 pcs/reel Label posted here Technical drawings according to DIN specifications 12.4 ± 1.5 Leader and trailer tape: Empty (160 mm min.) Parts mounted Direction of pulling out Device Lead I Lead II Collector Emitter Cathode Anode Anode Cathode Ø 1.55 ± 0.05 I VEMT2000 VEMT2500 X 2:1 4 ± 0.1 2 ± 0.05 VEMD2000 5.5 ± 0.05 VEMD2500 VSMB2000 VSMG2000 VSMY2850RG 3.05 ± 0.1 II 12 ± 0.3 Terminal position in tape 1.75 ± 0.1 Empty (400 mm min.) 4 ± 0.1 Drawing-No.: 9.800-5100.01-4 Issue: 2; 18.03.10 21572 Fig. 14 - Reel and Blister Tape of SMD Dome Lens, 1.8 mm, Reverse Gullwing Rev. 1.5, 02-Mar-15 Document Number: 80090 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors Reel X Unreel direction 5± Ø 62 ± 0.5 2. Ø 13 ± 0.5 Ø 330 ± 1 0.5 Tape position coming out from reel 6000 pcs/reel Label posted here technical drawings according to DIN specifications 12.4 ± 1.5 Leader and trailer tape: Empty (160 mm min.) Parts mounted Direction of pulling out Ø 1.55 ± 0.05 Device Lead I Lead II Collector Emitter Cathode Anode Anode Cathode I VEMT2020 VEMT2520 X 2:1 4 ± 0.1 2 ± 0.05 VSMB2020 VEMD2020 VEMD2520 VSMY2850G 3.05 ± 0.1 4 ± 0.1 5.5 ± 0.05 VSMG2020 12 ± 0.3 Terminal position in tape 1.75 ± 0.1 Empty (400 mm min.) II Drawing-No.: 9.800-5091.01-4 Issue: 3; 18.03.10 21571 Fig. 15 - Reel and Blister Tape of SMD Dome Lens, 1.8 mm, Gullwing Rev. 1.5, 02-Mar-15 Document Number: 80090 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors Fig. 16 - Reel and Blister Tape of SMD Dome Lens, 1.8 mm, Side Looker Rev. 1.5, 02-Mar-15 Document Number: 80090 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information Vishay Semiconductors 16 ±0.2 Unreel direction X 2. 60.2 ±0.5 www.vishay.com 5 ±0 178 ±1 .5 0. 5 Tape position coming out from reel 13 ± X 13.2 ±1.5 Label posted here Leader and trailer tape: Empty leader (400 mm, min.) Parts mounted Drawing-No.: 9.800-5080.01-4 Direction of pulling out Issue: 3; 11.06.08 Empty trailer (200 mm, min.) 18033 Fig. 17 - Reel of TEMx1000 Series and TSMx1000 Series Quantity per Reel: 1000 pcs 3.05 ± 0.1 2 ± 0.05 5.5 ± 0.05 1.75 ± 0.1 4 ± 0.1 Ø 1.55 ± 0.05 Top tape Anode Feed direction 12 ± 0.3 0.3 4 ± 0.1 Push pin through hole Quantity per reel: 1000 pcs or 5000 pcs 18030 Fig. 18 - Blister Tape of TSMF1000, TSML1000, and TEMD1000 Rev. 1.5, 02-Mar-15 Document Number: 80090 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 3.05 ± 0.1 4 ± 0.1 Ø 1.55 ± 0.05 5.5 ± 0.05 1.75 ± 0.1 2 ± 0.05 12 ± 0.3 0.3 4 ± 0.1 Feed direction Anode Top tape Push pin through hole Quantity per reel: 1000 pcs or 5000 pcs 18031 Fig. 19 - Blister Tape of TSMF1020, TSML1020, and TEMD1020 3.05 ± 0.1 5.5 ± 0.05 1.75 ± 0.1 2 ± 0.05 Feed direction Top tape 12 ± 0.3 0.3 4 ± 0.1 Ø 1.55 ± 0.05 4 ± 0.1 Anode Push pin through hole 18032 Quantity per reel: 1000 pcs or 5000 pcs Fig. 20 - Blister Tape of TSMF1030, TSML1030, and TEMD1030 Rev. 1.5, 02-Mar-15 Document Number: 80090 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 3.05 ± 0.1 4 ± 0.1 5.5 ± 0.05 12 ± 0.3 1.75 ± 0.1 2 ± 0.05 Ø 1.55 ± 0.05 0.3 4 ± 0.1 Feed direction Collector Top tape Push pin through hole 18089 Quantity per reel: 1000 pcs or 5000 pcs Fig. 21 - Blister Tape of TEMT1000 3.05 ± 0.1 Feed direction Top tape 12 ± 0.3 1.75 ± 0.1 2 ± 0.05 5.5 ± 0.05 0.3 4 ± 0.1 Ø 1.55 ± 0.05 4 ± 0.1 Collector Push pin through hole 18090 Quantity per reel: 1000 pcs or 5000 pcs Fig. 22 - Blister Tape of TEMT1020 and TEMT1520 Rev. 1.5, 02-Mar-15 Document Number: 80090 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 3.05 ± 0.1 2 ± 0.05 5.5 ± 0.05 1.75 ± 0.1 4 ± 0.1 Ø 1.55 ± 0.05 Feed direction 12 ± 0.3 0.3 4 ± 0.1 Collector Top tape 18091 Push pin through hole Quantity per reel: 1000 pcs or 5000 pcs Fig. 23 - Blister Tape of TEMT1030 20874 Fig. 24 - Reel of TEMx6000, VEML60x0FX01 Series Quantity per Reel: 3000 pcs Rev. 1.5, 02-Mar-15 Document Number: 80090 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 4 0.3 ± 0.05 Ø 1.55 ± 0.05 Anode 12 ± 0.3 4.26 3° 5.5 1.75 2 1.35 Ø 1.5 min. 2.26 Cathode 4 Reel off direction Not indicated tolerances ±0.1 Drawing-No.: 9.700-5329.02-4 Issue: 2; 31.08.09 technical drawings according to DIN specifications 20877 Fig. 25 - Blister Tape of TEMD6010FX01 20876 Fig. 26 - Blister Tape of TEMT6000X01 Rev. 1.5, 02-Mar-15 Document Number: 80090 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 8.4 +2.5 Ø 177.8 max. Ø 55 min. 8.4 +0.15 Z Form of the leave open of the wheel is supplier specific. 14.4 max. Ø 20.2 min. 1.5 min. Ø 13 - 0.2 + 0.5 Z 2:1 Drawing-No.: 9.800-5096.01-4 Issue: 2; 26.04.10 20875 technical drawings according to DIN specifications Fig. 27 - Reel of TEMx6200X01, TEMx7x00X01, VSMB1940X01, VSMY1850X01 Series Quantity per reel: 3000 pcs Rev. 1.5, 02-Mar-15 Document Number: 80090 15 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 21501 Fig. 28 - Blister Tape of TEMD7x00X01, VSMB1940X01 Quantity per reel: 3000 pcs 20690 Fig. 29 - Blister Tape of TEMT7x00X01, TEMT6200FX01 Rev. 1.5, 02-Mar-15 Document Number: 80090 16 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors 4 Ø 1.55 ± 0.05 0.2 ± 0.05 2 ± 0.05 8 2.24 3.5 ± 0.05 1.75 Anode 0.94 Cathode 1.45 4 Ø 1.1 + 0.1 Not indicated tolerances ±0.1 Reel off direction Drawing-No.: 9.700-5352.01-4 Issue: 1; 13.04.10 technical drawings according to DIN specifications 22112 Fig. 30 - Blister Tape of VSMY1850, VSMY1850X01 TAPING OF T-1 (3 mm) AND T-1¾ (5 mm) DEVICES The taping specification is based on IEC publication 286, taking into account industrial requirements for automatic insertion. Absolute maximum ratings, mechanical dimensions, optical and electrical characteristics for taped devices are identical to basic catalog types and can be found in specifications for untaped devices. CODE FOR TAPED DEVICES Tape varieties A, B, C, E, F, G, M A The tapes of components are available on reels or in Ammopack. Each reel and each box is marked with label containing the following information: - Vishay S 1 2 12: Cathode/collector leaves the reel first 1: Cathode/collector 21: Anode/emitter leaves the reel first 2: Anode/emitter Note that the lead wires of taped components may be shorted or bent in accordance to the IEC standard. PACKAGING Spacing of lead frame S: 2.54 mm T: 5.08 mm A S Z 18801 Z: only for fan fold packing both polarities Fig. 31 - Taping Code Number of Packed Components T-1 (3 mm): 2000 pcs T-1¾ (5 mm): 1000 pcs - Type - Group - Tape code (see figure 24) - Productions code - Quantity Rev. 1.5, 02-Mar-15 Document Number: 80090 17 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors MISSING COMPONENTS Up to 3 consecutive components may be missing but the gap is followed by at least 6 components. A maximum of 0.5 % of components per reel quantity may be missing. At least 5 empty positions are present at the start and the end of the tape to enable tape insertion. Tensile strength of the tape: ≥ 15 N Pulling force in plane of the tape, at right angles to reel: ≥ 5 N Note • Shipment in fan-fold packages is standard for radial taped devices. Shipment in reel packing is only possible if the customer guarantees removal of empty reels. According to what is stated in a German packaging decree (Verpackungsverordnung) we are not able to accept return of reels. ORDERING CODE Type designations are extended by a code for the taping standard. Example: TSAL6200-AS12 (reel packing) TSAL6200-ASZ (fan-fold packing) BPW85-AS12 (reel packing) TABLE 4 - TAPING SURVEY OF LEADED COMPONENTS CODE FOR TAPING STANDARD “H“ - HEIGHT OF TAPING IN mm (TOLERANCES ± 0.5 mm) PREFERENCES 3 mm 5 mm SIDEVIEW’S 17.3 17.3 16.0 AS12 AS21 REMARKS Reel, cathode / collector leaves first Standard Reel, anode / emitter leaves first ASZ Ammopack KS12 Reel, cathode / collector leaves first KS21 19.3 19.3 - - Reel, anode / emitter leaves first KSZ Ammopack CS12 Reel, cathode / collector leaves first CS21 22.0 22.0 - Reel, anode / emitter leaves first CSZ Ammopack ES12 Reel, cathode / collector leaves first ES21 - 24.0 24.0 Standard ESZ EGZ Ammopack - - Ammopack 2 mm pin distance lead to lead 24.0 MS12 MS21 Reel, cathode / collector leaves first 25.5 25.5 - Reel, anode / emitter leaves first MSZ Ammopack GSZ - - 29.0 FSZ - - 27.0 FGZ - - 27.0 Rev. 1.5, 02-Mar-15 Reel, anode / emitter leaves first Ammopack 2 mm pin distance lead to lead Standard Ammopack Ammopack 2 mm pin distance lead to lead Document Number: 80090 18 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters AMMOPACK The tape is folded in a concertina arrangement and laid in a cardboard box. 355 52 max. 90 If components are required to have the cathode or collector leave the box first (figure 27), then open the box at the side marked with the “-” symbol. If anode or emitter should leave the box first, then open at the side marked with the “+” symbol. 30 Tape feed direction Diodes: cathode before anode Transistors: collector before emitter Identification label: Vishay/type/group/tape code/production code/quantity 48 45 948641 Fig. 32 - Dimensions of the Reel Label Tape feed direction Diodes: anode before cathode Transistors: emitter before collector Diodes: anode before cathode Phototransistors: emitter before collector Code 21 Adhesive tape Identification label Reel C Diodes: cathode before anode Phototransistors: collector before emitter Code 12 A Paper B 94 8667 Tape 94 8671 Fig. 34 - Tape Feed Direction Fig. 33 - Components on Tape and Reel TABLE 5 - INNER DIMENSIONS OF AMMOPACK Rev. 1.5, 02-Mar-15 A mm B mm C mm 340 46 125 T-1¾ (5 mm) 340 34 140 T-1 (3 mm) AS-taping 340 41 140 T-1 (3 mm) other than AS-taping 348 43 125 FSZ side view lens 348 46 125 GSZ side view lens COMPONENTS Document Number: 80090 19 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors TAPING OF T-1 (3 mm) PACKAGES TAPING OF T-1¾ (5 mm) PACKAGES Polarity options: Z, 12, 21 Polarity options: Z, 12, 21 TABLE 6 - POSITION OF T-1 (3 mm) COMPONENTS IN TAPE TABLE 7 - POSITION OF T-1¾ (5 mm) COMPONENTS IN TAPE OPTION H PREFERENCE OPTION H PREFERENCE AS 17.3 ± 0.5 mm recommended AS 17.3 ± 0.5 mm recommended MS 25.5 ± 0.5 mm recommended CS 22.0 ± 0.5 mm ±1 KS 19.3 ± 0.5 mm MS 25.5 ± 0.5 mm CS 22.0 ± 0.5 mm ES 24.0 ± 0.5 mm ±2 12.7 ± 1 recommended ±2 ±1 “H” 2.54 5.08 ± 0.7 6.35 12.7 ± 0.2 +1 12 ± 0.3 ± 0.2 + 0.6 - 0.1 18 -0.5 0.9 max. Ø4 9 ± 0.5 0.3 ± 0.2 ± 0.5 9 12 ± 0.3 18 +1 - 0.5 0.3 ± 0.2 12.7 ± 1 ± 0.7 0.9 max. Ø 4 ± 0.2 Measure limit over 20 index-holes: ± 1 2.54 Quantity per: Reel (Mat. - No. 1764) 2000 +0.6 -0.1 5.08 ± 0.7 6.35 ± 0.7 12.7 ± 0.2 Measure limit over 20 index-holes: ± 1 Reel (Mat.-no. 1764) 94 8171 Quantity per: Fig. 35 - Taping of T-1 (3 mm) Devices 1000 94 8172 Fig. 36 - Taping of T-1¾ (5 mm) Devices Bend leads: Lead standard xG Straight leads: Lead standard xS Option AS Ammopack Quantity per: H 16 ± 0.5 mm ES 24 ± 0.5 mm FS 27 ± 0.5 mm GS 29 EG 24 ± 0.5 mm FG 27 ± 0.5 mm + 0.2 - 0.5 mm (Mat. - No. 1763) 2000 18886 Fig. 37 - Taping of Side View Lens Packages Rev. 1.5, 02-Mar-15 Document Number: 80090 20 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging and Order Information www.vishay.com Vishay Semiconductors Reel (Mat. - No. 1764) Quantity per: Option H AS 16 ± 0.5 mm ES 24 ± 0.5 mm MS 25.5 ± 0.5 mm 1000 18887 Fig. 38 - Taping of Side View PIN Photodiodes TUBE PACKAGING OF TOP VIEW PIN PHOTODIODES BP104S AND BPW34S Dimensions in millimeters 10.7 Quantity per tube: 45 pcs Quantity per box: 1800 pcs 9.5 214.5 Stopper 18800 Fig. 39 - Drawing Proportions Not Scaled Rev. 1.5, 02-Mar-15 Document Number: 80090 21 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000