NSVS1107

NSVS1107 Jan. 2014
New JRC SAW FILTER
NSVS1107
Application
449.7MHz Low Power Transceiver
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Spec.
Typ.
Input and Output Impedance
50
Nominal Center Frequency (f0)
449.7MHz
Insertion Loss
449.2~450.2MHz
3.5dB max.
2.5dB
Response Variation
449.2~450.2MHz
1.5dB max.
0.5dB
Input and Output VSWR
449.2~450.2MHz
2.5 max.
1.5
Out of Band Rejection
420.0 MHz
25dB min.
60dB
(Relative to Through Level)
428.3 MHz
50dB min.
60dB
471.1 MHz
40dB min.
50dB
(Operating Temperature Range: - 10~+60ºC)
Maximum Rating: (Table 2)
Table 2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+20dBm
7.5V
-10~+60ºC
-20~+70ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSVS1107 Jan. 2014
IN
50
1
OUT
50
6
2 SAW 5
3
4
Fig.1 Measuring circuit
(a)
3. 0±0. 15
( b)
3. 0 ± 0. 1 5
420
XF
( c)
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
2
5
( 0. 6)
[ 2 x]
3
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
1-9--10-19--20-31--(2) Part Number Mark
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Pin no.
1
2
3
4
5
6
Connection
GND
IN/OUT
GND
GND
OUT/IN
GND
X
Y
Z
0
1
2
NSVS1107 Jan. 2014
Notice
1. Use this co mponent within operating tempera ture range. It might n ot be
satisfied with electrical specificatio n without operating te mperature range.
When it is used less tha n -10ºC or more than +60ºC, it mig ht be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature c hange for cleaning af ter reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do no t apply st atic electricity or excessive volt age while
assembling and measuring. And do not transpo rt this component with bare
hand.
7. As it might be a cau se of degrada tion or de struction to apply D.C. volt age
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single un it. Make
sure that this component is evaluate d and confir med against this sp ecification
when it is mounted to your products.
2. The information cont ained herein may be changed with out prior no tice. It is
therefore advisable to contact Japan Radio Company before proceeding with the
design of equipment incorporating this product.
3.
The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). Jap an Radio Comp any does not assu me any
liability for the case using the pro ducts with t he application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please
contact our sales representatives in advance.
NSVS1107 Jan. 2014
IN
50 O
９
10
*27nH
８
７
６
11
SAW
39pF
12
１
33pF
0
Fig.1 Measuring circuit
20
2
13.30±0.20
(a)
40
(b)
(1.26±0.13)
(C)
4
(2)
60
6
J4Y1
VS971
80
100
Insertion Loss [dB]
Insertion Loss [dB]
４
*murata LQW18A series
(1)
6.5±0.20
３
OUT
50 O
FREQUENCY CHARACTERISTICS
S21
0
２
*27nH
５
8
10
CH1 : center 449.7 span 100
CH2 : center 449.7 span 100
S11
(R0.3)
[4×]
S22
(3)
Marking
(1) Manufacture's Mark
(2) Lot Number
(a) Year
2.0 max.
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
S11
(2.54)S22
(2.54)
11
1-9 --- 0
11
9
10-19 --- 1
9
VSWR
7
5
3
(2.54±0.15)
1
399.7
499.7
20-31 --- 2
7
(3) Part Number Mark
5
3
(1.4)
1
399.7
[12×]
InsertionLoss [dB]
(2.54±0.15)
0
Frequency [MHz]
S21
12
20
1
2
3
4
5
40
11 10
60
9
1
499.7
(0.8)
Frequency [MHz]
Pin No. Connection
8
7
6
[12 ×]
VSWR(0.76)
(c) Date
2
GND(PKG)
3
GND(PKG)
4
GND(PKG)
5
(R0.3)
100
0.3
[12×]
Fig.2 Package
dimensions(in
mm)
Frequency
[MHz]
OUT/IN
6
GND(signal)
7
GND(PKG)
8
GND(PKG)
9
GND(PKG)
10
GND(PKG)
11
80
GND(PKG)
12
3000
IN/OUT
GND(signal)