NSVS1120

NSVS1120 Apr. 2013
NewJRC SAW FILTER
NSVS1120
Application
570MHz WLAN IF
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Input and Output Impedance
Nominal Center Frequency (f0)
Insertion Loss
561.5~578.5MHz
Response Variation
561.5~578.5MHz
Input and Output VSWR
561.5~578.5MHz
Group Delay Ripple
561.5~578.5MHz
Out of Band Rejection
370~548MHz
(Relative to
553MHz
Through Level)
555MHz
585MHz
587MHz
592~770MHz
Spec.
4.7dB max.
2.5dB max.
3.0 max.
50nsec max.
30dB min.
7dB min.
5dB min.
5dB min.
7dB min.
30dB min.
Typ.
50Ω
570MHz
3.8dB
1.7dB
2.5
20nsec
37dB
10dB
7dB
7dB
10dB
35dB
(Operating Temperature Range : -20~+60ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+10dBm
7.5V
-20~+60ºC
-30~+80ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSVS1120 Apr. 2013
6
1
20pF
20pF
2 SAW5
15n H
15n H
IN
50Ω
4
3
OUT
50Ω
Fig.1 Measuring circuit
(a)
3. 0±0. 15
( b)
3. 0 ± 0. 1 5
221
( c)
MB
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
( 0. 6)
[ 2 x]
3
2
5
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
*1-9--10-19--20-31--(2) Part Number Mark
Pin no.
1
2
3
4
5
6
Connection
GND
IN/OUT
GND
GND
OUT/IN
GND
X
Y
Z
0
1
2
NSVS1120 Apr. 2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -20ºC or more than +60ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact New Japan Radio Company before proceeding
with the design of equipment incorporating this product.
3.
The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). New Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please
contact our sales representatives in advance.
NSVS1120 Apr. 2013
IN
50 O
10
*27nH
９
８
７
６
11
SAW
39pF
12
１
33pF
0
Fig.1 Measuring circuit
10
2
13.30±0.20
(a)
20
(b)
(1.26±0.13)
(C)
4
(2)
30
6
J4Y1
VS971
40
50
Insertion Loss [dB]
Insertion Loss [dB]
４
*murata LQW18A series
(1)
6.5±0.20
３
FREQUENCY CHARACTERISTICS
S21
0
２
OUT
50 O
*27nH
５
8
10
CH1 : center 570 span 200
CH2 : center 570 span 200
S11
(R0.3)
[4×]
S22
(3)
Marking
(1) Manufacture's Mark
(2) Lot Number
(a) Year
2.0 max.
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
S11
(2.54)S22
(2.54)
11
1-9 --- 0
11
9
10-19 --- 1
9
VSWR
7
5
3
(2.54±0.15)
1
470
670
20-31 --- 2
7
(3) Part Number Mark
5
3
(1.4)
1
470
[12×]
Frequency [MHz]
250
200
12
1
2
4
3
5
150
100
11 10
9
1
670
(0.8)
GroupDelay [nsec]
(2.54±0.15)
Frequency [MHz]
Pin No. Connection
7
8
6
[12 ×]
(0.76)
VSWR
(c) Date
2
GND(PKG)
3
GND(PKG)
4
GND(PKG)
5
(R0.3)
0
470
570
[12×]
Fig.2 Package dimensions(in mm)
OUT/IN
6
GND(signal)
7
GND(PKG)
8
GND(PKG)
9
GND(PKG)
10
GND(PKG)
11
50
GND(PKG)
12
670
IN/OUT
GND(signal)