DO5010H

Document 284-1
SMT Power Inductors - DO5010H Series
•Irms ratings up to 15 A; saturation currents up to 30 A
• Heavy gauge wire for low DC resistance
Designer’s Kit C355 contains 3 of each part
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant tin-silver over copper. Other
terminations available at additional cost.
Weight 3.2 – 4.0 g
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 250 per 13″ reel Plastic tape: 32 mm wide,
0.38 mm thick, 24 mm pocket spacing, 7.8 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
DCRSRF
Inductance2 max
typ3 Isat4 Irms5
Part Number1 ±20% (µH) (mOhm) (MHz) (A)
(A)
DO5010H-781ML_
0.78
2.6156 30 15
DO5010H-152ML_
1.5
4.0100 25 15
DO5010H-222ML_
2.2
6.1 75 2012
DO5010H-332ML_
3.3
8.6 60 1710
DO5010H-392ML_ 3.9
10 55159.0
DO5010H-472ML_ 4.7
14 40138.4
DO5010H-602ML_ 6.0
17 35127.5
DO5010H-782ML_ 7.8
18 35117.5
DO5010H-103ML_ 10
26 28106.0
DO5010H-123ML_12
28268.5
5.2
DO5010H-153ML_15
32208.0
4.4
DO5010H-223ML_22
47207.0
3.5
DO5010H-333ML_33
66155.5
3.0
DO5010H-473ML_ 47
86
9 4.52.6
DO5010H-683ML_ 68
130
8 3.52.3
DO5010H-104ML_ 100
190
7 3.01.8
DO5010H-154ML_ 150
250
6 2.61.5
DO5010H-224ML_ 220
380
5 2.41.2
DO5010H-334ML_ 330
560
4 1.91.0
DO5010H-474ML_ 470
850
3 1.40.82
DO5010H-684ML_ 680
1100
2.5 1.20.72
DO5010H-105ML_ 1000
1800
2.0 1.00.56
1. When ordering, please specify termination and packaging codes:
DO5010H-105MLD
Termination: L= RoHS compliant tin-silver over copper.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging:D
=13″ machine-ready reel. EIA-481 embossed plastic
tape.
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter D instead.
2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4284A
LCR meter or equivalent.
3. SRF measured using Agilent/HP 8753D network analyzer.
4. DC current at which the inductance drops 10% (typ) from its value
without current.
5. Current that causes a 40°C temperature rise from 25°C ambient.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 284-1 Revised 02/25/15
Document 284-2
SMT Power Inductors - DO5010H Series
Typical L vs Frequency
Typical L vs Current
10000
10000
1000 µH
100 µH
100
10 µH
10
100 µH
100
10 µH
10
0.78 µH
1
0.78 µH
1
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
0.1
0.1
0.01
0.1
1
Frequency (MHz)
10
0.1
1
Current (A)
0.500
12,70
Irms Derating
10
100
Note:
Maximum height: 0.315
for -781 to -153
8,00
0.300
for -223 to -683
7,62
0.280
for -104 to -105
7,11
Note
0.730
max
18,54
0.561
min
14,25
0.075
1,90
0.250
6,35
0.600
max
15,24
0.065
max
1,65
0.200
max
5,08
0.710
max
18,03
Internal code
Recommended
Land Pattern
Dash number
XXX
X
Part Marking
0.626
15,90
Part marking since Feb. 2005. Parts manufactured
inches
prior to that date may have color dots.
Dimensions are in
mm
Visit www.coilcraft.com/colrpowr.cfm
for color dot marking details.
Document 284-2 Revised 02/25/15
Similar pages