UNISONIC TECHNOLOGIES CO., LTD UALD11060 Preliminary CMOS IC HIGH POWER FACTOR LINEAR CONSTANT CURRENT LED DRIVER DESCRIPTION UTC UALD11060 is a high power factor linear constant current LED driver which is applied to LED lighting. Through the distinctive constant current control technology, it realizes that constant current accuracy is less than ±5% and output current is adjustable through external resistor. High power factor and low harmonic distortion are the particular features. The system is simple without transformer and electrolysis capacitor. Therefore, LED lighting batch job can be realized. HSOP-8 FEATURES * No transformer and high voltage electrolysis capacitor * Integrated high voltage startup power supply circuit * Adjustable output current, max 60mA * Inter-chip current deviation < ±5% * Efficiency: >90% * Power factor: >0.95 * THD<20% * Over temperature protection * Application system no EMI problems ORDERING INFORMATION Ordering Number UALD11060G-SH2-R Package HSOP-8 Packing Tape Reel UALD11060G-SH2-R (1)Packing Type (1) R: Tape Reel (2)Package Type (2) SH2: HSOP-8 (3)Green Package (3) G: Halogen Free and Lead Free MARKING www.unisonic.com.tw Copyright © 2016 Unisonic Technologies Co., Ltd 1 of 6 QW-R125-045 .a UALD11060 Preliminary CMOS IC PIN CONFIGURATION OUT4 1 8 GND OUT3 2 7 NC OUT2 3 6 NC OUT1 4 5 REXT PIN DESCRIPTION PIN NO. 1 2 3 4 5 6~7 8 PIN NAME OUT4 OUT3 OUT2 OUT1 REXT NC GND DESCRIPTION current output port 4 current output port 3 current output port 4 Power input and constant current output port 1 Output current setting port GND UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R125-045 .a UALD11060 Preliminary CMOS IC ABSOLUTE MAXIMUM RATING (Ambient temperature is 27°C if there is no special instruction) PARAMETER SYMBOL RATINGS UNIT ESD Voltage Withstand VESD > 2000 V Operating Temperature TOPR -20 ~ +125 °C Storage Temperature TSTG -40 ~ +150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. ELECTRICAL CHARACTERISTICS (Ambient temperature is 27°C if there is no special instruction) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX OUT1 Input Voltage VOUT1 6.5 Output Current IOUT 10 60 REXT Port Voltage VREXT VOUT1=VOUT4=10V 0.9 OUT1/ OUT2 Port Withstand Voltage VDS_BV1 IOUT1=IOUT2=0 200 OUT3/ OUT4 Port Withstand Voltage VDS_BV2-4 IOUT3=IOUT4=0 150 IOUT Accuracy dIOUT IOUT=10~50mA ±5 Over-Temperature Protection Point (Note 1) TSC 110 Note: When the junction temperature is over 110°C, the output current of UALD11060 will be reduced. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw UNIT V mA V V V % °C 3 of 6 QW-R125-045 .a UALD11060 Preliminary CMOS IC FUNCTIONAL DESCRIPTION UTC UALD11060 is constant current drive which integrates the functional module such as LED constant current control and OUT port high voltage drive. OUT1 port minimum input voltage is 6V （IOUT=20mA）and it can reach output current 10mA ~ 60mA by external REXT resistor. Built-in LED constant current drive maintains LED current a high precision without impact of ambient temperature. The chip can achieve high efficiency and high power factor by opening four switches one by one. The chip output current is adjustable by REXT resistor IOUT=VREXT/R. Output current generated by four switches opening one by one is shown below: IOUT1=0.57V/R IOUT2=0.73V/R IOUT3=0.87V/R IOUT4=0.95V/R UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 6 QW-R125-045 .a UALD11060 Preliminary CMOS IC TYPICAL APPLICATION CIRCUIT VIN Vac UTC UALD11060 5 REXT OUT1 4 6 NC 7 NC OUT2 3 OUT3 2 8 GND OUT4 1 Figure 1. UTC Typical Schematic Circuit Diagram 18×2 12×2 6×2 5×2 VIN Vac UTC UALD11060 30R 5 REXT OUT1 4 6 NC OUT2 3 7 NC OUT3 2 8 GND Figure 2. UTC UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw OUT4 1 Typical Application Circuit 5 of 6 QW-R125-045 .a UALD11060 CMOS IC OUT4 1 8 GND OUT4 1 8 GND OUT2 3 OUT3 2 7 NC 6 NC OUT2 3 OUT3 2 7 NC 6 NC 5 REXT OUT1 4 UTC UALD11060 5 REXT OUT1 4 TYPICAL APPLICATION CIRCUIT (Cont.) UTC UALD11060 Preliminary UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R125-045 .a