The following document contains information on Cypress products. FUJITSU SEMICONDUCTOR SUPPORT SYSTEM SS01-71050-1E DSU-FR EMULATOR LQFP-176P HEADER TYPE 3 MB2198-301 OPERATION MANUAL PREFACE ■ Purpose and intended readership of this manual Thank you for purchasing the LQFP-176P Header Type 3 for the DSU-FR Emulator (MB2198301) . This product is used together with the BGA-660P adapter for the DSU-FR Emulator (MB2198300) *1 to connect the DSU-FR Emulator (MB2198-01) *2 and FR-DSU cable (MB2198-10) *3 to a user system that uses a MB91460 series Fujitsu FR *4 microcontroller (LQFP-176P) *5. This manual describes how to use the LQFP-176P Header Type 3 for the DSU-FR Emulator. Please read the manual carefully before using. Please contact your Fujitsu sales or support representative for details of which production and evaluation MCU models can be used with this product. *1 : *2 : *3 : *4 : *5 : referred below as the "adapter" referred below as the "emulator" referred below as the "DSU cable" FR is an abbreviation of FUJITSU RISC CONTROLLER and is a product of Fujitsu. The package is the FPT-176P-M07 (0.5 mm lead pitch, 24 mm × 24 mm body size). ■ Safe use of this product This manual contains important information relating to the safe use of this product. Please read this before using the product and use the product correctly in accordance with the instructions in this manual. In particular, carefully read "Caution of the products described in this manual" at the beginning of this manual and "2.Precautions When Using this Product" to understand the requirements for safe use of the product before using it. After reading the manual, keep it handy for future reference. ■ Warranty and liability The specifications of this product are subject to change without notice. Also, please note that Fujitsu accepts no responsibility for any consequences that result either directly or indirectly from the use of this product. ■ Product operating environment This product has an operating temperature range of 5 °C to 35 °C and an operating humidity range of 20 % to 80 %. Use the product in an environment that is free of condensation and avoid high temperature or humidity. This product consists of an open circuit board without a frame cabinet with exposed electronic components. Accordingly, do not place other objects on top of the circuit board and do not allow the metal parts of the unit to come into contact with people or materials that may have a build up of static electricity. Similarly, keep any objects that are flammable, likely to cause a short circuit, or cause any other such problem well away from the unit when the power to the unit is turned on. Keep the unit horizontal as far as possible and do not use in locations that are subject to vibration, dust, flammable gases, or other such dangers. If the unit is used in an environment that does not satisfy the above guidelines, there is a risk of unexpected damage to property or injury to the user or other people in the vicinity. Also, please keep the packaging materials supplied with the unit and reuse these if the unit ever needs to be returned due to a fault or other reason. ■ Related manuals Please refer also to the following manuals. • DSU-FR Emulator MB2198-01 Hardware Manual • DSU-FR Emulator DSU-FR Cable MB2198-10 Operation Manual • DSU-FR Emulator MB2198-300 BGA-660P Adapter Operation Manual i ■ Caution of the products described in this document The following precautions apply to the product described in this manual. WARNING Electric shock, Damage Electric shock, Damage Indicates a potentially hazardous situation which, if not avoided appropriately, could result in death or serious injury and/or a fault in the user’s system. Before performing any operation described in this manual, turn off all the power supplies to the system. Performing such an operation with the power on may cause an electric shock or device fault. Once the product has been turned on, do not touch any metal part of it. Doing so may cause an electric shock or device fault. CAUTION Indicates a potentially hazardous situation which, if not avoided appropriately, may result in minor or moderate injury and/or damage to the product or the equipment to which the product is connected, to software resources such as data, or to other properties. Cuts, Damage Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your steps when carrying the product. Do not use the product at an unstable location such as a place exposed to strong vibration or a sloping surface. Doing so may let the product fall, resulting in an injury or fault. Cuts The product has some sharp-pointed or edged parts inevitably exposed, such as jumper plugs. Use meticulous care in handling the product not to get injured with such pointed parts. Damage Neither put anything on or apply shock to the product. Once the product has been powered, do not carry it. Doing either may cause a fault due to a load or shock. Damage Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong magnetic or electric field for an extended period of time. An adverse operating or storage environment can cause a fault. Damage Use the product within the ranges of its general specifications. Operating it outside the range of any general specification may cause a fault. Damage To prevent electrostatic breakdown, do not let your finger or an object touch any metal part of the connector. Before handling the product, touch a metal object (such as a door knob) to discharge static electricity from your body. Damage When turning the power on or off, follow the relevant procedure described in this document. Before turning the power on, in particular, be sure to finish making all the required connections. To set up and use the product, follow the instructions given in this document. Using the product incorrectly or inappropriately may cause a fault. Damage Before plugging or unplugging any cable for this product, be sure to turn the power supply off. When unplugging the cable, remove it while holding the connector without pulling the cable itself. Pulling the cable itself or bending it may expose or disconnect the cable core, resulting in a fault. Damage Although the MCU socket is structured not to accept an evaluation MCU in a wrong orientation or position, pay due attention to the mounting orientation when mounting the evaluation MCU. Forcing the evaluation MCU to be inserted in a wrong orientation can damage the pins of the evaluation MCU and the accidental insertion prevention mechanism of the socket, resulting in a fault. Damage When stored, the product should be kept in its packaging box as it has no housing. Re-transporting the product may damage it to cause a fault. Keep the packaging materials used for shipment of the product and use them when re-transporting it. ii • The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. • The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the information. • Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. • The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. • Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. • If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. ©2005 FUJITSU LIMITED Printed in Japan iii 1. Product Overview 1.1 Overview This product is an option product for use with the DSU-FR emulator and is intended to support the development of user systems that use the Fujitsu FR family of microcontrollers. The main features of the header board are as follows. • Used in conjunction with the adapter (separately available) to connect the user system to an emulator. • When using the MB91V460 to emulate an MB91460 series MCU, the header board performs level shifting the 5 V output signals of MB91V460 or user system to 3.3 V. 1.2 Check package contents Before starting to use the header board, check that the following items are all present. • LQFP-176P header *1 • Header board attachment screws (M2 × 10 mm, 0.4 mm pitch) • Washers • NQPACK176SD *2 • HQPACK176SD *3 • Operation Manual (Japanese) • Operation Manual (English, this document) :1 :4 :4 :1 :1 :1 :1 *1 : Referred to below as the "header board". The header board installs the adapter I/F connector and YQPACK176DS (Tokyo Eletech Corporation, referred to below as the “YQPACK”) . *2 : IC socket (Tokyo Eletech Corporation, referred to below as the "NQPACK") . Includes a dedicated screwdriver and three guide pins. If you provide the required screw holes in printed circuit board for user system for attaching the IC socket, you can use the highly reliable NQPACK176SD-SL adapter socket (Tokyo Eletech Corporation, sold separately) . Please contact Tokyo Eletech for details. *3 : IC socket cover (Tokyo Eletech Corporation, referred to below as the “HQPACK”) . Four screws (M2 × 6 mm, 0.4 mm pitch) are supplied for attaching the HQPACK. Please contact Fujitsu sales or support representative for details of which mass production MCU models can be used with this product. 1 1.3 Option Products Table 1.1 shows the option products available for the header board. Please purchase these separately, as required. Table 1.1 Option Products Name Model DSU-FR emulator MB2198-01 DSU-FR cable MB2198-10 BGA-660P adapter *1 MB2198-300 Evaluation MCU *2 MB91V460 *1 : When used together with the BGA-660P adapter for the DSU-FR Emulator (Model No: MB2198-300) , the header board can be used as an adapter unit. Refer to the "DSU-FR Emulator MB2198-300 BGA-660P Adapter Operation Manual" for details including how to handle the adapter, how to use it, and safety precautions. *2 : Evaluation MCUs are mounted in the adapter. Please contact Fujitsu sales or support representative for details of evaluation MCU corresponding to another adapter. 2 1.4 System Configuration The header board is used together with an emulator, adapter, and other components to connect to the user system. Figure1.1 shows the system configuration to this product. General-purpose External trigger/ measurement program execution equipment Host computer RS232C, USB, LAN AC in AC adapter DSU-FR emulator unit DSU-FR cable AC adapter AC in Evaluation MCU Adapter Header board User system Figure 1.1 System Configuration To use the emulator, a host computer and emulator/debugger software are required separately. Please refer to the operation manual for the adapter for details about how to connect the adapter and header board. Refer to the header board's hardware manual, operation manual, and other support documentation for details of the emulator, adapter, and other specifications. 3 1.5 External View and Names of Each Part Figure 1.2 shows the external view of the header board and the names of each part. Note that Figure 1.2 shows the state of the header board when it is shipped. 1 2 10 9 8 7 6 5 4 3 No. Part No. Part ➀ Adapter I/F connector 1 ➅ YQPACK ➁ Adapter I/F connector 2 ➆ VCCB2 jumper plug ➂ VCC5 jumper plug ➇ VCCB1 jumper plug ➃ VCCB4 jumper plug ➈ VCCB5 jumper plug ➄ VCCB3 jumper plug ➉ Pull-up resistor Figure 1.2 External View of Header Board 4 2. Precautions When Using this Product Take the precautions and restrictions below when using the header board. ■ Precautions • Operating the device outside the range of any general specification may cause the device to malfunction. Use the device in the ranges of its general specifications. • Please follow this manual about setting and using the adapter. • Table 2.1 lists the temperature and humidity ranges for operating and storing the unit. Table 2.1 Operation and Storage Conditions Temperature Humidity Operation 5 °C to 35 °C 20 % to 80 % (with no condensation) Storage 0 °C to 70 °C 20 % to 80 % (with no condensation) ■ Points to note when designing the printed circuit board for the user system A height restriction applies to any components on the user system that are located close to where the header board connects to the user system. Take note of this when designing the printed circuit board for the user system. 54 mm 150 mm 72 mm 23 mm 115 mm Adapter Insulating plate Header 10 mm approx 17 mm. 1.6 mm approx 13 mm. User system *: NAPACK176SD The height differs slightly depending on how the YQPACK and the NQPACK are engaged. Figure 2.1 Header Board Dimensions 5 ■ Points to note when designing the MCU foot pattern The figure shows the recommended foot pattern dimensions for mounting the NQPACK on the printed circuit board for the user system. Please take account of the NQPACK foot pattern requirements as well as the recommended foot pattern for the mass production MCU when designing the printed circuit board for the user system. Contact Tokyo Eletech Co. Ltd. for more details. 0.5 mm 10 mm 0.25 mm 2 mm 0.5 × 43 = 21.5 mm 27.1 mm 10 mm 23.1 mm No.1 Pin φ 3.2 mm SL-type 3- φ 1.0 mm *1 : *2 : Position of guide pin holes (φ 1.0 mm) used to align the NQPACK when mounting. These holes are not required if not using the guide pins. Position of IC socket attachment screw holes (φ 3.2 mm) required if using the NQPACK176SD-SL (sold separately by Tokyo Eletech Corporation) instead of the NQPACK176SD supplied with the header board. These holes are not required if not using the NQPACK176SD-SL. Figure 2.2 Foot Pattern Dimensions for Mounting the NQPACK ■ Restrictions The following general restrictions apply to the header board. • When using the adapter and header, the MCU on the user system must be mounted in a socket. Use the NQPACK176SD (Tokyo Eletech Corporation) as the IC socket. • Ensure that all power is turned off to the adapter, emulator, and user system before setting the jumpers on the header board. • The configuration of the level shift circuit is such that VOH for signals that expect a 4.5 V output is limited to 4.4 V. • As no level shift function is provided for pins 89 to 108, the output signal level depends on the power supply used to drive these pins. 6 3. Connection 3.1 Connecting the Header Board to the User System Mount the supplied NQPACK on the user system before using the header board. The header board is used together with the adapter. Refer to the hardware manual for the adapter for details about how to connect the header board and adapter. ■ Connection procedure 1. To connect the header board to the user system, align the index mark (▲) on the header board with pin 1 on the NQPACK mounted on the user system. Pin 1 on the NQPACK is also indicated by an index mark (▲) (See Figure 3.1) . As the YQPACK pins are thin and easily bent, check that the YQPACK pins are kept straight when inserting into the NQPACK. 2. Insert the header board attachment screws, together with washers, into the four screw holes in the top of the header board and tighten the diagonally opposite screws in turn (See Figure 3.2) . Use the dedicated screwdriver supplied with the NQPACK to tighten the screws and tighten each screw equally in turn. Take care not to over-tighten as this may cause a bad connection. 176SD TET NQPACK Index (▲) Header board index (▼) Figure 3.1 Index Positions 7 Header board attachment screws Washers Header board YQPACK NQPACK User system Figure 3.2 Header Board Connection Procedure ■ Disassembly procedure To remove the header board, first remove the four screws and then lift the header board vertically up/off the NQPACK. 8 3.2 Mounting a Mass Production MCU Model Use the supplied HQPACK to mount the mass production MCU in the user system. 1. Align the index mark on the mass production MCU (●) with the index mark on the NQPACK mounted on the user system (▲), and then insert. 2. Check that the mass production MCU is correctly inserted into the NQPACK, and then align the index marks on the HQPACK and NQPACK (angle cut linearly at one place only) and insert (See Figure 3.3). As the HQPACK pins are thin and easily bent, check that the HQPACK pins are kept straight when inserting into the NQPACK. 3. Insert the four screws for attaching the HQPACK into the four screw holes in the top of the HQPACK and tighten the diagonally opposite screws in turn. Use the dedicated screwdriver supplied with the NQPACK to tighten the screws and tighten each screw equally in turn. Take care not to over-tighten as this may cause a bad connection. Attachment screws HQPACK Mass Production MCU NQPACK User system Figure 3.3 Mounting a Mass Production MCU Model ■ Disassembly procedure To remove the HQPACK, first remove the four screws and then lift the HQPACK vertically up/off the NQPACK. 9 4. Operation The following describes how to set the various settings, and the procedure for turning the power on and off. Be sure to read the setting as shown below before turning on the power. 4.1 Jumper Plug Settings ■ VCC5 jumper plug setting Figure 4.1 shows the factory setting and setting meaning of VCC5 jumper plugs. Please set it to the terminal number in which the terminal VCC3 is impressed to a different voltage among terminals VCC5 of mass production MCU (The terminal number: 133,147,162,176) . Moreover, please set it to either of terminal even when you use mass production MCU in a single power supply. VCC5 S6 133 NC NC 176 147 NC NC 162 Setting Meaning 133 Apply voltage at pin 133 of the mass production MCU, voltage being different from the VCC3 pin. 147 Apply voltage at pin 147 of the mass production MCU, voltage being different from the VCC3 pin. 162 Apply voltage at pin 162 of the mass production MCU, voltage being different from the VCC3 pin. 176 Apply voltage at pin 176 of the mass production MCU, voltage being different from the VCC3 pin. Figure 4.1 VCC5 Jumper Plug Settings 10 ■ VCCB1 to VCCB5 settings Figure 4.2 describes the factory setting of VCCB1 to VCCB5 jumper plugs and the setting of the jumper plugs. S4 VCC5H VCC3H VCCB4 VCCB3 S3 VCC5H VCC3H VCCB2 S2 VCC5H VCC3H VCCB1 S1 VCC5H VCC3H VCCB5 S5 VCC5H Jumper plug Setting VCC3H Meaning Remarks VCC5H Adjust the level of group 1 output signals Select this setting if connecting a 5 V to 4.4 V. ± 10 % power supply to pin 176. VCC3H Adjust the level of group 1 output signals Select this setting if connecting a 3.3 V between 3.6 V and 3.0 V. ± 0.3 V power supply to pin 176. VCC5H Adjust the level of group 2 output signals Select this setting if connecting a 5 V to 4.4 V. ± 10 % power supply to pin 162. VCC3H Adjust the level of group 2 output signals Select this setting if connecting a 3.3 V between 3.6 V and 3.0 V. ± 0.3 V power supply to pin 162. VCC5H Adjust the level of group 3 output signals Select this setting if connecting a 5 V to 4.4 V. ± 10 % power supply to pin 147. VCC3H Adjust the level of group 3 output signals Select this setting if connecting a 3.3 V between 3.6 V and 3.0 V. ± 0.3 V power supply to pin 147. VCC5H Adjust the level of group 4 output signals Select this setting if connecting a 5 V to 4.4 V. ± 10 % power supply to pin 133. VCC3H Adjust the level of group 4 output signals Select this setting if connecting a 3.3 V between 3.6 V and 3.0 V. ± 0.3 V power supply to pin 133. VCC5H Adjust the level of group 5 output signals Select this setting if connecting a 5 V to 4.4 V. ± 10 % power supply to the VCC3 pin. VCC3H Adjust the level of group 5 output signals Select this setting if connecting a 3.3 V between 3.6 V and 3.0 V. ± 0.3 V power supply to the VCC3 pin. VCCB1 VCCB2 VCCB3 VCCB4 VCCB5 Figure 4.2 VCCB1 to VCCB5 Jumper Plug Settings 11 For method to select each jumper plug, when the power supply connected to VCC3 is 3.3 V ± 0.3 V, VCCB5 should be set to VCC3H. In this case, the jumper plugs corresponding to the VCC5 pins that have a power supply with a voltage different to VCC3 (5 V ± 10 %) should be set to VCC5H. The jumpers for the pins with the same power supply voltage as VCC3 should be set to VCC3H. The following shows an example. Example VCC3 = 3.3 V Pin 133 (VCC5) = 3.3 V Pin 147 (VCC5) = 5 V Pin 162 (VCC5) = 5 V Pin 176 (VCC5) = 5 V Jumper plug settings VCCB1 = VCC5H VCCB2 = VCC5H VCCB3 = VCC5H VCCB4 = VCC3H VCCB1 = VCC3H When the power supply connected to VCC3 is 5 V ± 10 %, VCCB5 should be set to VCC5H. In this case, the jumper plugs corresponding to the VCC5 pins that have a power supply with a voltage different to VCC3 (3.3 V ± 0.3 V) should be set to VCC3H. The jumpers for the pins with the same power supply voltage as VCC3 should be set to VCC5H. The following shows an example. Example VCC3 = 5 V Pin 133 (VCC5) = 3.3 V Pin 147 (VCC5) = 5 V Pin 162 (VCC5) = 5 V Pin 176 (VCC5) = 5 V Jumper plug settings VCCB1 = VCC5H VCCB2 = VCC5H VCCB3 = VCC5H VCCB4 = VCC3H VCCB1 = VCC5H If connecting a single power supply (5 V ± 10 % or 3.3 V ± 0.3 V) to both VCC3 and VCC5, the unit will operate correctly regardless of the settings (VCC5H or VCC3H) . 4.2 Use of Pull-Up Resistor ■ Use of pull-up resistor A 100 kΩ pull-up resistor is connected to pin 99 on the mass production MCU which connects to the VCC3 power supply. The output signal from the header to this pin does not contain any component other than the pull-up. If this pull-up component is not required by the user system, please remove the resistor. 12 5. Specifications 5.1 General specifications Table 5.1 lists the general specifications of the header board. Table 5.1 General Specifications Item Specification LQFP-176P Header Type 3 (Model No.: MB2198-301) Product name (model no.) Remarks ⎯ VCC5 (note) 3.0 V to 5.5 V Supplied for user system VCC3 (note) 3.0 V to 5.5 V Supplied for user system VCC5H UVCC5+1 V (lower limit 4.0 V, upper limit 5.4 V) Supplied for adapter Requires level shifter VCC3H UVCC3+1 V (lower limit 4.0 V, upper limit 5.4 V) Supplied for adapter Requires level shifter Operating temperature and storage temperature Operation: 5 °C to 40 °C Storage : 0 °C to 70 °C No condensation Operating humidity and storage humidity Operation: 20 % to 80 % Storage: 20 % to 80 % No condensation External dimensions 150 mm (W) × 115 mm (D) × 23 mm (H) ⎯ Weight 84.8 g ⎯ User system power supply Header power supply Note : The operating voltage range may be differed for some evaluation MCUs. 13 5.2 Function Specifications Table 5.2 lists the function specifications of the header board. Table 5.2 Function Specifications of Header Board Item Header board Specification Connects the user system and adapter. The header board includes a level shifter used to convert the VCC5 level output signals of the MB91V460 or user system to the VCC3 level when using the MB91V460 (evaluation MCU: user I/O uses a single VCC5 power supply) to emulate an MB91461 or other MB91460 series mass production MCU (user I/O uses dual VCC5 and VCC3 power supplies) . The potential of level-shifted signals corresponding to VCC5 and VCC3 are in the range upper limit = 4.4 V, lower limit = 3 V (error for each power supply is ± 1 V or less) . Note that the circuit configuration means that I/O pins that expect VCC5 level signals will have a signal level of 4.4 V or less. The following shows an example of level shifting when VCC5 = 5 V and VCC3 = 3.3 V. Level shift function MB91V460 Level Shift Mass Production MCU VCC5 I/O pin output = 5 V → VCC5 I/O pin input = 4.4 V VCC5 I/O pin output = 5 V → VCC3 I/O pin input = 3.3 V VCC5 I/O pin input = 4.4 V ← VCC5 I/O pin output = 5 V VCC5 I/O pin input = 3.3 V ← VCC3 I/O pin output = 3.3 V The level shift function separates the power supply pins that drive the mass production MCU's I/O pins (VCC3 pin, pin 133 (VCC5) , pin 147 (VCC5) , pin 162 (VCC5) , and pin 176 (VCC5) ) into five groups and sets up level shifting independently for each group. The settings are specified using the VCCB1 to VCCB5 jumper plugs. Figure 5.1 shows the make up of each group. Note that level shifting is not performed for pins 89 to 108 on the mass production MCU. Power supply 14 Selects the power supply with different potential to VCC3 among the MB91461’s VCC5 pins (pin 176, 162, 147, or 133) and connects it to the adapter Use the VCC5 jumper plug to set this selection. 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Group 1 (driven by pin 176) Group 2 (driven by pin 162) Group 3 (driven by pin 147) Group 4 (driven by pin 133) YQPACK TOP View Group 5 (driven by VCC3 pin) Group 5 (driven by VCC3 pin) Group 5 (driven by VCC3 pin) 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 Level shift function not supported 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 Figure 5.1 Grouping for Level Shift Function 15 5.3 Connector Specifications ■ YQPACK specifications On the header board, the signals from the evaluation MCU mounted on the adapter are connected in accordance with the mass production MCU pin layout (same layout as YQPACK) via the two adapter interface connectors on the header board. Refer to the data sheet or hardware manual of the mass production MCU for information about its pin layout. Tables 5.3, 5.4, 5.5, and 5.6 list the pin layouts for the adapter board interface connectors. Note : • The "A row" in the table titles refers to the side of the connector that has the polarity marking. The "B row" refers to the other side. • "O" in the CBTS column indicates that the signal goes from the YQPACK176SD to adapter interface connector 1 or 2 via the level shifter (SN74CBTS16211, Texas Instruments Incorporated) . • VCC3 connects to the VCC3 pin on the mass production MCU. • VCC5 connects to VCC5 pins on the mass production MCU (pin 133, 147, 162, or 176) . Use the VCC5 jumper plug on the header board to specify the pins to which to connect. 16 Table 5.3 Adapter Interface Connector 1 (Row A) Connector Pin No. A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 Mass Production MCU Pin No. ⎯ ⎯ 27 26 ⎯ ⎯ 24 25 22 23 ⎯ ⎯ 18 19 16 17 ⎯ 15 ⎯ ⎯ ⎯ ⎯ 29 28 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 21 20 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Pin Name CBTS VCC5 VCC5 WR1X WR0X NC NC BGRNTX RDX RDY BRQ GND GND CS1X CS0X CS3X CS2X NC CS4X NC NC GND GND ASX SYSCLK NC NC NC NC NC NC GND GND IOWRX IORDX NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Connector Pin No. A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76 A77 A78 A79 A80 A81 A82 A83 A84 A85 A86 A87 A88 A89 A90 A91 A92 A93 A94 A95 A96 A97 A98 A99 A100 Mass Production MCU Pin No. ⎯ ⎯ 9 8 ⎯ 10 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 169 168 171 170 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 158 157 160 159 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 82 ⎯ ⎯ ⎯ ⎯ 131 ⎯ ⎯ ⎯ ⎯ Pin Name CBTS GND GND DACKX0 DREQ0 NC DEOP0 NC NC NC NC GND GND P141 P140 P143 P142 NC NC NC NC GND GND P151 P150 P153 P152 NC NC NC NC NC NC NC NC GND NC NC NC NC NC NMIX NC NC VCC5 GND INITX GND NC GND VCC5H ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 17 Table 5.4 Adapter Interface Connector 1 (Row B) Mass Connector Production Pin Name CBTS Pin No. MCU Pin No. B1 ⎯ NC ⎯ B51 B2 ⎯ NC ⎯ B52 B3 ⎯ NC ⎯ B53 B4 ⎯ NC ⎯ B54 B5 ⎯ NC ⎯ B55 B6 ⎯ NC ⎯ B56 B7 ⎯ NC ⎯ B57 B8 ⎯ NC ⎯ B58 B9 83 P167 B59 B10 ⎯ NC ⎯ B60 B11 ⎯ GND ⎯ B61 B12 ⎯ GND ⎯ B62 B13 173 P171 B63 B14 172 P170 B64 B15 175 P173 B65 B16 174 P172 B66 B17 85 P175 B67 B18 84 P174 B68 B19 87 P177 B69 B20 86 P176 B70 B21 ⎯ GND ⎯ B71 B22 ⎯ GND ⎯ B72 P181 B73 155 B23 B24 154 P180 B74 B25 ⎯ NC ⎯ B75 B26 156 P182 B76 B27 ⎯ NC ⎯ B77 B28 ⎯ NC ⎯ B78 B29 ⎯ NC ⎯ B79 B30 ⎯ NC ⎯ B80 B31 ⎯ GND ⎯ B81 B32 ⎯ GND ⎯ B82 B33 149 P191 B83 B34 148 P190 B84 B35 ⎯ NC ⎯ B85 B36 150 P192 B86 B37 152 P195 B87 B38 151 P194 B88 B39 ⎯ NC ⎯ B89 B40 153 P196 B90 B41 ⎯ GND ⎯ B91 B42 ⎯ GND ⎯ B92 141 P201 B93 B43 B44 140 P200 B94 B45 ⎯ NC ⎯ B95 B46 142 P202 B96 B47 144 P205 B97 B48 143 P204 B98 B49 ⎯ NC ⎯ B99 B50 145 P206 B100 * : C (pin B95) is connected to pin 14 and pin 31 of the YQPACK176SD. Connector Pin No. 18 Mass Production MCU Pin No. ⎯ ⎯ 135 134 ⎯ 136 138 137 ⎯ 139 ⎯ ⎯ ⎯ 165 167 166 119 118 5 4 ⎯ ⎯ 123 122 125 124 ⎯ 163 ⎯ 164 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 14/31 ⎯ ⎯ ⎯ ⎯ ⎯ Pin Name CBTS GND GND P211 P210 NC P212 P215 P214 NC P216 GND GND NC P220 P223 P222 P225 P224 P227 P226 GND GND P231 P230 P233 P232 NC P234 NC P236 NC NC NC NC NC NC NC NC GND NC NC NC NC VCC5 C* NC NC NC NC VCC3H ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Table 5.5 Adapter Interface Connector 2 (Row A) Connector Pin No. Mass Production MCU Pin No. Pin Name CBTS A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 ⎯ ⎯ 117 116 119 118 7 6 121 120 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 109 108 111 110 ⎯ 112 ⎯ ⎯ VCC3 VCC3 P241 P240 P243 P242 P245 P244 P247 P246 GND GND NC NC NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC GND GND P281 P280 P283 P282 NC P284 NC NC ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Connector Pin No. Mass Production MCU Pin No. Pin Name CBTS A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76 A77 A78 A79 A80 A81 A82 A83 A84 A85 A86 A87 A88 A89 A90 A91 A92 A93 A94 A95 A96 A97 A98 A99 A100 ⎯ ⎯ 101 100 103 102 105 104 107 106 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 36 38 40 42 ⎯ 47 49 51 53 129 127 ⎯ 115 113 113 ⎯ ⎯ ⎯ ⎯ ⎯ GND GND P291 P290 P293 P292 P295 P294 P297 P296 GND GND NC NC NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC D16 D18 D20 D22 GND D25 D27 D29 D31 MD0 MD2 NC AVRH AVSS AVSS VCC3 GND NC GND GND ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 19 Table 5.6 Adapter Interface Connector 2 (Row B) 20 Connector Pin No. Mass Production MCU Pin No. Pin Name CBTS B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 55 54 59 56 61 60 NC NC NC NC NC NC NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC NC GND GND A1 A0 A3 A2 A5 A4 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Connector Pin No. Mass Production MCU Pin No. Pin Name B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 B83 B84 B85 B86 B87 B88 B89 B90 B91 B92 B93 B94 B95 B96 B97 B98 B99 B100 63 62 64 ⎯ 66 65 68 67 70 69 ⎯ 71 75 72 77 76 79 78 81 80 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 37 39 41 43 46 48 50 52 ⎯ 128 ⎯ ⎯ 114 114 115 ⎯ ⎯ 33 ⎯ 34 A7 A6 A8 GND A10 A9 A12 A11 A14 A13 GND A15 A17 A16 A19 A18 A21 A20 A23 A22 NC GND NC NC NC NC NC NC GND NC D17 D19 D21 D23 D24 D26 D28 D30 GND MD1 NC NC AVCC3 AVCC3 AVRH VCC3 GND X0 GND X1 CBTS ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ SS01-71050-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM DSU-FR EMULATOR LQFP-176P HEADER TYPE 3 MB2198-301 OPERATION MANUAL December 2005 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.