TAI-SAW TECHNOLOGY CO., LTD. No. 3, Industrial 2nd Rd., Ping-Chen Industrial District, Taoyuan, 324, Taiwan, R.O.C. TEL: 886-3-4690038 FAX: 886-3-4697532 E-mail: [email protected] Web: www.taisaw.com Approval Sheet For Product Specification Issued Date: 12/12/2005 (REV. NO: 2) Product Name: SMD 3.2x2.5 26.0MHz VCTCXO TST Parts No.: TX0161A Customer Parts No.: Company: Division: Approved by: Date: Checked by: CC Hsu Approval by: TF Yang Date: 12/12/2005 TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document FR-03S06-02 TAI-SAW TECHNOLOGY CO., LTD. No. 3, Industrial 2nd Rd., Ping-Chen Industrial District, Taoyuan, 324, Taiwan, R.O.C. TEL: 886-3-4690038 FAX: 886-3-4697532 E-mail: [email protected] Web: www.taisaw.com SMD 3.2x2.5 26.0MHz VCTCXO MODEL NO.: TX0161A REV. NO.: 2 Features: Ultra Miniature SMD Package Good Frequency Stability Good Phase Noise Response RoHS Compliant Lead free Lead-free soldering Description and Applications: Surface mount 3.2mmx2.5mm VCTCXO for use in wireless communications devices Electrical Specifications: TX0161A Specifications Nominal Frequency, Fo 26.000000 MHz Storage Temperature Range -40°C to +85°C Operating Temperature Range -20°C to +75°C Power Supply Voltage, Vcc 2.8 V Output Voltage with Load 10pF//10KΩ, Vout 0.8 Vp-p min Output Waveform Clipped Sinewave Power Supply Current, Icc 2.0 mA max Control Voltage, Vcon 1.4 +/- 1.0 V DC Terminal Input Impedance 100K ohms min Frequency Tolerance (Vcon=1.4V) after Two Reflows Frequency Stability a. Vs. Temperature (-20~75°C) b. Vs. Load varied 10pF//10KΩ+/-10% c. Vs. Supply Voltage varied 2.8+/-5% +/- 1.5 ppm max @ 25°C +/- 3°C +/- 2.5 ppm +/- 0.2 ppm +/- 0.2 ppm Vcon Frequency Control Range (1.4+/-1.0 V) +/-8 ~ +/-14 ppm Start Up Time (90% of final RF level in Vp-p) 2.0 msec max. Harmonics -5.0 dBc max SSB Phase Noise (@1KHz Carrier Offset) -130 dBc/Hz max TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 2 Phase Noise Plot: Mechanical Dimensions (mm): Marking: Line 1: 26.00 (Frequency) Line 2: YYWW+S (YY 05 is for year 2005 & WW is for week number) TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 3 Recommended Circuit Recommended Reflow Soldering Condition Packing (mm): 1. Reel Dimension TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 4 2. Tape Dimension [NOTE]: 1. Unless otherwise specified tolerance on dimension +/-0.1 mm. 2. Material: conductive polystyrene with color black 3. 10 pitch cumulative tolerance +/-0.2 mm. Notes of the Usage: 1. Touch the solder iron at 260+/-5 deg C onto the leads for 10+/-2 sec max or touch the solder at 350+/-5 deg C onto the leads for 3+/-0.5 sec. 2. In the customer’s reflow process, if it will remain some mechanical stress at the soldering terminals, also make some cracks on the soldering termination. Some cracks will cause open or short circuit and cause of thermal increasing or smoking. Don’t make any excess mechanical stress to soldering points. 3. In case of giving a heavy shock to the products, it may make an open or short circuit and cause of thermal increasing and smoking. To avoid heavy shock impact applying to products is strictly required. Notes of the Storage: 1. To keep products under the condition at the room temperature (-5~35 deg C) with normal humidity (45~75%). Absorption of moisture and dewdrop may make inferiority of characteristics and a short circuit. 2. Oxidization of terminals shall make the solderability more inferior. Dusts and corrosive gas will make a cause of the open or short circuit. Keep it in the clean place where is not in dusty and no corrosive gas. TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 5 3. Use the unti-static material to the storage package. 4. Don’t put any excess weight to the TCXO in the storage process. 5. Don’t move the product from the cold place to the hot place in the short time, otherwise it may make some dew-drop, then a short circuit may happen in case. 6. Storage periods should be maximum 6 months under condition of above item 1 after delivery from TST factory. 7. Once open the bag, there is possibility of electrical characteristics deterioration due to absorption of moisture. So, please use parts within 7 days after opening the bag. 8. If you have to keep parts without using after opening the bag, please put the drying agent in the bag, fold the bag and keep it in the place where temperature and humidity are controlled (nitrogen atmosphere box etc.) TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 6