PPMxx-X-xxDLF PPM-SERIES Rev.07-2010 5 - 20 Watt Univ. 85-264VAC and 50/60Hz Triple Output Overload Protection 3 kV AC I/O Isolation Low Ripple and Noise High Efficiency Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PPM-Series are high efficiency green power moduls with various packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments. EMC and safety standards meet international standards IEC61000 UL60950 and IEC60950, and Multi-certificate is in processing. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range Input Frequency Input (Inrush) Current 85 – 264 VAC or 120 – 370 VDC universal 47 – 63 Hz 110 VAC 230 VAC 120mA (10A), typ. 70mA (20A), typ. 230mA (10A), typ. 120mA (20A), typ. 250mA (10A), typ. 140mA (20A), typ. 330mA (16A), typ. 180mA (30A), typ. PPM05 models PPM10 models PPM15 models PPM20 models External Input Fuse (recommended) PPM05 models 1A / 250V slow blow PPM10 / 15 models 2A / 250V slow blow PPM20 models 3.15A / 250V slow blow Output Specifications Voltage Accuracy Input variation Load variation (10-100% Balance Load) ±2% (main output) ±0.5% (main output) ±1.5% (supplement output) Vo1: ±3% ±Vo2: ±5% 10% ≤ 100mV pk-pk (main output) Continuous, auto recovery ≥ 110% Io Minimum load Ripple and Noise (20Mhz bandwidth) Short Circuit Protection Over Current Protection Over output voltage protection 5VDC models ≤7.5VDC 12 / 15VDC models ≤20VDC 24VDC models ≤30VDC PPM-Series – PPMxx-X-xxDLF – Triple Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/5 PPMxx-X-xxDLF Common Specifications Temperature range Power derating Case temperature Storage Hold up Time Humidity (non condensing) Temperature Coefficient -25°C to +70 °C 3.75% / °C (above 55°C) +90°C (max) -25°C to +105 °C 80mS, typ. (230VAC) 85%, max. 0.02%/°C (main output) 0.15%/°C (supplement output) 150kHz, max. 3000VAC / 1min. 0.3mA RMS typ. (230VAC / 50Hz) EN55022, level B Switching Frequency I/O Isolation Voltage Leakage current EMI / RFI conducted EMC compliance ESD RF EFT / bursts Surge Safety Standarts Safety Approvals Safety Class Case Material Reliability Calculated MTBF (MIL-HDBK-217F) Weight IEC/EN 61000-4-2 level 3 6KV/8KV IEC/EN 61000-4-3 IEC/EN 61000-4-4 level 3 2KV IEC/EN 61000-4-5 level 3 1KV / 2KV IEC60950, EN60950, UL60950 EN60950, IEC60950, UL60950 CLASS 1 UL94V-0 rated > 300,000 hrs 50g (PPM05) 70g (PPM10) 80g (PPM15) 120g (PPM20) Notes: PPM-Series – PPMxx-X-xxDLF – Triple Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/5 Selection Guide Triple Output Order # P r ow e (W ) 1 O ut o lta t2 V u O / g DC) e (V 1/ Out 2C O ut nt F urre (m oad u ll L A) y( ienc Effic TRIPLE OUTPUT PPM05-A-0505DLF PPM05-A-0512DLF PPM05-A-0515DLF PPM05-A-0524DLF 5 5 5 5 5/±5 5 / ± 12 5 / ± 15 5 / ± 24 800 / ± 100 600 / ± 100 600 / ± 80 600 / ± 50 70 73 74 75 PPM10-B-0512DLF PPM10-B-0515DLF 10 10 5 / ± 12 5 / ± 15 1000 / ± 200 900 / ± 200 75 75 PPM15-C-0505DLF PPM15-C-0512DLF PPM15-C-0515DLF PPM15-C-0524DLF 15 15 15 15 5/±5 5 / ± 12 5 / ± 15 5 / ± 24 2000 / ± 500 2000 / ± 200 1800 / ± 200 2000 / ± 100 75 77 78 78 PPM20-D-0512DLF PPM20-D-0515DLF PPM20-D-0524DLF 20 20 20 5 / ± 12 5 / ± 15 5 / ± 24 2000 / ± 400 2000 / ± 300 2000 / ± 200 75 76 77 %) If you need other specifications, please enquire. Notes: PPM-Series – PPMxx-X-xxDLF – Triple Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/5 Package / Pinning / Derating PIN CONNECTIONS # TRIPLE 1 Ground 2 AC (N) 3 AC (L) 4 - Vout 1 5 +Vout 1 6 - Vout 2 7 Common 8 +Vout 2 TRIM No Pin No. PPM05-A A 12.5 B 48.5 C 40.5 D 4.0 E 16.0 F 36.0 G 20.5 H min. 6.0 No. A B C D E F G H PPM10-B 17.5 55.0 47.0 5.0 20.0 45.0 20.5 min. 6.0 No. PPM15-C A 17.5 B 62.0 C 54.0 D 5.0 E 20.0 F 48.0 G 22.5 H min. 6.0 No. A B C D E F G H PPM20-D 20.0 70.0 62.0 5.75 23.0 48.0 23.5 min. 6.0 Load（%） 100 80 60 40 -40 -10 55 Temperature（℃） PPM-Series – PPMxx-X-xxDLF – Triple Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/5 70 App Notes: (Triple Output) L F use N +Vo1 NT C L N EXTERNAL CAPACITORS TYPICAL VALUE (µ µF) C1 C2 TVS1 RL MODEL PPM05-A-0505DLF PPM05-A-0512DLF PPM05-A-0515DLF PPM05-A-0524DLF PPM10-B-0512DLF PPM10-B-0515DLF PPM15-C-0505DLF PPM15-C-0512DLF PPM15-C-0515DLF PPM15-C-0524DLF PPM20-D-0512DLF PPM20-D-0515DLF PPM20-D-0524DLF -Vo1 +Vo2 C3 C4 TVS2 RL Co m -Vo2 C5 C6 TVS3 RL Remark: 1. Output filtering capacitors C1, C2 and C3 are electrolytic capacitors, It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. C2,C4,C6 are use to filter high frequency noise. TVS is recommended component to protect post-circuits (if converter fails). 2. External input NTC is recommended to use 5D-9 (Only PPM10 models and PPM15 models) C1 220 120 120 120 220 220 470 470 470 470 330 330 330 C3 22 22 22 22 68 47 220 120 120 120 120 120 47 C5 22 22 22 22 68 47 220 120 120 120 120 120 47 Parallel Lines Measure Copper sheet Fuse C1 C2 Load Connect Oscillograph Probe 2 25.4m m 25.4m m Notes: PPM-Series – PPMxx-X-xxDLF – Triple Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 5/5