A3280, A3281, and A3283: Chopper-Stabilized, Precision Hall-Effect Latches

A3280, A3281, and A3283
Chopper-Stabilized, Precision Hall-Effect Latches
Discontinued Product
This device is no longer in production. The device should not be
purchased for new design applications. Samples are no longer available.
Date of status change: January 31, 2011
Recommended Substitutions:
For existing customer transition, and for new customers or new applications, refer to the A1220, A1221, and A1223.
NOTE: For detailed information on purchasing options, contact your
local Allegro field applications engineer or sales representative.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan
for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The
information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
A3280, A3281, and A3283
Chopper-Stabilized, Precision
Hall-Effect Latches
Features and Benefits
Description
▪ Symmetrical switch points
▪ Resistant to physical stress
▪ Superior temperature stability
▪ Output short-circuit protection
▪ Operation from unregulated supply
▪ Reverse battery protection
▪ Solid-state reliability
▪ Small size
The A3280, A3281, and A3283 Hall-effect latches
are extremely temperature-stable and stress-resistant
sensor ICs especially suited for operation over extended
temperature ranges to +150°C. Superior high-temperature
performance is made possible through dynamic offset
cancellation, which reduces the residual offset voltage
normally caused by device overmolding, temperature
dependencies, and thermal stress. The three devices are
identical except for magnetic switch points.
Packages:
Each device includes on a single silicon chip a voltage
regulator, Hall-voltage generator, small-signal amplifier,
chopper stabilization, Schmitt trigger, and a short-circuit
protected open-collector output to sink up to 25 mA.
A south pole of sufficient strength will turn the output
on. A north pole is necessary to turn the output off. An
on-board regulator permits operation with supply voltages
of 4.2 to 24 volts.
Package LH
Package LT
Not to scale
Package UA
Three package styles provide a magnetically optimized
package for most applications. Package type LH is a
modified SOT23W surface-mount package, LT is a
miniature SOT89/TO-243AA transistor package for
surface-mount applications; while UA is a three-lead
ultra-mini-SIP for through-hole mounting. Each package
type is lead (Pb) free (suffix, –T), with 100% matte tin
leadframe plating.
Functional Block Diagram
27609.20-DS, Rev. M
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
Selection Guide
Part Number
Packing*
Mounting
A3283ELTTR-T
7-in. reel, 1000 pieces/reel
SOT89 Surface Mount
Bulk, 500 pieces/bag
3-pin SIP through hole
A3283LLHLT-T
7-in. reel, 3000 pieces/reel
SOT23W Surface Mount
A3283LLTTR-T
7-in. reel, 1000 pieces/reel
SOT89 Surface Mount
Bulk, 500 pieces/bag
3-pin SIP through hole
A3283EUA-T
A3283LUA-T
Ambient, TA
(°C)
BRP(MIN)
(TA = 25°C)
(G)
BOP(MAX)
(TA = 25°C)
(G)
–180
180
–40 to 85
–40 to 150
*Contact Allegro for additional packing options.
Absolute Maximum Ratings
Characteristic
Symbol
Notes
Rating
Units
Supply Voltage
VCC
26.5
V
Reverse Battery Voltage
VRCC
–30
V
Magnetic Flux Density
B
Unlimited
G
Output Off Voltage
VOUT
26
V
Continuous Output Current
IOUT
25
mA
Reverse Output Currrent
IROUT
Internal current limiting is intended to protect
the device from output short circuits.
–50
mA
Range E
–40 to 85
ºC
Range L
Operating Ambient Temperature
TA
–40 to 150
ºC
Maximum Junction Temperature
TJ(max)
165
ºC
Tstg
–65 to 170
ºC
Storage Temperature
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
2
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
X
PTCT
2
3
OUTPUT
1
GROUND
CC
SUPPLY
V
Dwg. PH-003-2
Suffix '–LT' & '–UA' Pinning
(SOT89/TO-243AA & ultra-mini SIP)
Suffix ‘–LH’ Pinning
(SOT23W)
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
3
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
ELECTRICAL CHARACTERISTICS over operating temperature range.
Limits
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
4.2
–
24
V
Supply Voltage Range
VCC
Operating, TJ < 170°C1
Output Leakage Current
IOFF
VOUT = 24 V, B < BRP
–
–
10
μA
VOUT(SAT)
IOUT = 20 mA, B > BOP
–
185
500
mV
Output Saturation Voltage
Output Current Limit
IOM
B > BOP
30
–
60
mA
Power-On Time
tpo
VCC > 4.2 V
–
–
50
μs
Chopping Frequency
fC
–
340
–
kHz
Output Rise Time
tr
RL = 820 , CL = 20 pF
–
0.2
2.0
μs
Output Fall Time
tf
RL = 820 , CL = 20 pF
–
0.1
2.0
μs
B < BRP, VCC = 12 V
–
3.0
8.0
mA
B > BOP, VCC = 12 V
–
4.0
8.0
mA
VRCC = -30 V
–
–
-5.0
mA
Supply Current
ICC
Reverse Battery Current
ICC
Zener Voltage
VZ + VD
ICC = 15 mA, TA = 25°C
28
32
37
V
Zener Impedance
zz + zD
ICC = 15 mA, TA = 25°C
–
50
–

NOTES:
1. Maximum voltage must be adjusted for power dissipation and junction temperature.
2. BOP = operate point (output turns on); BRP = release point (output turns off).
3. Typical Data is at TA = +25°C and VCC = 12 V and is for design information only.
MAGNETIC CHARACTERISTICS over operating voltage range.
Part Numbers1
A3280
Characteristic
Test Conditions
Operate Point, BOP
A3281
A3283
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Units
at TA = +25°C and TA = max.
5.0
22
40
15
50
90
100
150
180
G
at TA = -40°C
5.0
–
40
15
–
90
100
–
200
G
at TA = +25°C and TA = max.
-40
-23
-5.0
-90
-50
-15
-180
-150
-100
G
at TA = -40°C
-40
–
-5.0
-90
–
-15
-200
–
-100
G
Hysteresis, Bhys
at TA = +25°C and TA = max.
10
45
80
30
100
180
–
300
360
G
(BOP - BRP)
at TA = -40°C
–
–
80
–
–
180
–
–
360
G
Release Point, BRP
NOTES:
1. Complete part number includes a suffix to identify operating temperature range (E or L) and package type (LH, LT, or UA).
2. As used here, negative flux densities are defined as less than zero (algebraic convention) and -50 G is less than +10 G.
3. Typical Data is at TA = +25°C and VCC = 12 V and is for design information only.
4. 1 gauss (G) is exactly equal to 0.1 millitesla (mT).
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
4
A3280, A3281
and A3283
Chopper-Stabilized, Precision
Hall-Effect Latches
TYPICAL OPERATING CHARACTERISTICS
as a function of temperature
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
TYPICAL OPERATING CHARACTERISTICS
as a function of temperature (cont'd)
OUTPUT SATURATION VOLTAGE
SUPPLY CURRENT
6.0
300
IOUT = 20 mA
V CC = 12 V
V CC = 12 V
5.0
200
4.0
OUTPUT ON, B > B OP OP
100
3.0
0
-50
-25
0
25
50
75
100
125
150
2.0
OUTPUT OFF, B < BRP
-50
-25
0
RP
25
50
75
100
125
150
AMBIENT TEMPERATURE IN °C
AMBIENT TEMPERATURE IN °C
Dwg. GH-028-5
Dwg. GH-029-4
TYPICAL OPERATING CHARACTERISTICS
as a function of supply voltage
A3281* SWITCH POINTS
A3280* SWITCH POINTS
80
40
OPERATE POINT
OPERATE POINT
40
20
T A = 150°C
T A = -40°C
0
-20
-40
3.0
-40
RELEASE POINT
3.5
4.0
4.5
T A = 150°C
T A = -40°C
0
5.0
24
-80
3.0
RELEASE POINT
3.5
4.0
4.5
24
5.0
SUPPLY VOLTAGE IN VOLTS
SUPPLY VOLTAGE IN VOLTS
Dwg. GH-021-3
Dwg. GH-021-1
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
TYPICAL OPERATING CHARACTERISTICS
as a function of supply voltage (cont’d)
OUTPUT SATURATION VOLTAGE
250
IOUT = 20 mA
T A = 150°C
T A = +25°C
T A = -40°C
225
200
175
150
3.0
3.5
4.0
4.5
24
5.0
SUPPLY VOLTAGE IN VOLTS
Dwg. GH-055-1
SUPPLY CURRENT
8.0
OUTPUT ON
T A = 150°C
T A = +25°C
T A = -40°C
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0
3.0
4.0
5.0
6.0
7.0
8.0
SUPPLY VOLTAGE IN VOLTS
9.0
10
11
12
Dwg. GH-058-4
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
FUNCTIONAL DESCRIPTION
Chopper-Stabilized Technique. The Hall element can be
considered as a resistor array similar to a Wheatstone bridge. A
large portion of the offset is a result of the mismatching of these
resistors. These devices use a proprietary dynamic offset cancellation technique, with an internal high-frequency clock to reduce
the residual offset voltage of the Hall element that is normally
caused by device overmolding, temperature dependencies, and
thermal stress. The chopper-stabilizing technique cancels the
mismatching of the resistor circuit by changing the direction of
the current flowing through the Hall plate using CMOS switches
and Hall voltage measurement taps, while maintaing the Hallvoltage signal that is induced by the external magnetic flux. The
signal is then captured by a sample-and-hold circuit and further
processed using low-offset bipolar circuitry. This technique
produces devices that have an extremely stable quiescent Hall
output voltage, are immune to thermal stress, and have precise
recoverability after temperature cycling. This technique will
also slightly degrade the device output repeatability. A relatively
high sampling frequency is used in order that faster signals can
be processed.
More detailed descriptions of the circuit operation can be
found in: Technical Paper STP 97-10, Monolithic Magnetic Hall
Sensing Using Dynamic Quadrature Offset Cancellation and
Technical Paper STP 99-1, Chopper-Stabilized Amplifiers With A
Track-and-Hold Signal Demodulator.
Operation. The output of these devices switches low (turns
on) when a magnetic field perpendicular to the Hall element
exceeds the operate point threshold (BOP). After turn-on, the
output is capable of sinking 25 mA and the output voltage is
VOUT(SAT). Note that the device latches; that is, a south pole of
sufficient strength towards the branded surface of the device
will turn the device on; removal of the south pole will leave the
device on. When the magnetic field is reduced below the release
point (BRP), the device output goes high (turns off). The difference in the magnetic operate and release points is the hysteresis
(Bhys) of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical
vibration and electrical noise.
Powering up in the absence of a magnetic field (less than
BOP and higher than BRP) will allow an indeterminate output
state. The correct state is warranted after the first excursion
beyond BOP or BRP.
It is strongly recommended that an external bypass capacitor
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
8
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
APPLICATIONS INFORMATION
be connected (in close proximity to the Hall element) between the
supply and ground of the device to reduce both external noise and
noise generated by the chopper-stabilization technique.
The simplest form of magnet that will operate these devices is
a ring magnet. Other methods of operation, such as linear magnets, are possible.
Extensive applications information for Hall-effect devices is
available in:
• Hall-Effect IC Applications Guide, Application Note 27701;
• Guidelines for Designing Subassemblies Using Hall-Effect De-
vices, Application Note 27703.1
More detailed descriptions of the chopper-stabilized circuit operation can be found in:
• Monolithic Magnetic Hall Sensing Using Dynamic Quadrature
Offset Cancelation, Technical Paper STP 97-10; and
• Chopper-Stabilized Amplifiers With A Track-and-Hold Signal
Demodulator, Technical Paper STP 99-1.
All are provided at
www.allegromicro.com
3
SUPPLY
2
PTCT
OUTPUT
V
1
CC
0.1 MF
SUPPLY
Dwg. EH-013
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
9
X
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
Package LH, 3-Pin (SOT-23W)
+0.12
2.98 –0.08
1.49 D
4°±4°
3
A
+0.020
0.180–0.053
0.96 D
+0.10
2.90 –0.20
+0.19
1.91 –0.06
2.40
0.70
D
0.25 MIN
1.00
2
1
0.55 REF
0.25 BSC
0.95
Seating Plane
Gauge Plane
8X 10° REF
B
PCB Layout Reference View
Branded Face
1.00 ±0.13
+0.10
0.05 –0.05
0.95 BSC
0.40 ±0.10
For Reference Only; not for tooling use (reference dwg. 802840)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Active Area Depth, 0.28 mm REF
B
Reference land pattern layout
All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary
to meet application process requirements and PCB layout tolerances
C
Branding scale and appearance at supplier discretion
D
Hall element, not to scale
NNT
1
C
Standard Branding Reference View
N = Last two digits of device part number
T = Temperature code
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
10
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
Package LT, 3-Pin SOT89
4.50±0.10
+0.10
1.73 –0.11
2.50
2.00
A
2.24
0.80
1.14
+0.15
4.10 –0.16
+0.15
2.45 –0.16
+0.09
2.20 –0.07
2.60
+0.20
1.00 –0.11
1
2
3
4.60
Parting
Line
1.00
+0.04
0.40 –0.05
0.70
1.50±0.10
B
1.50
PCB Layout Reference View
Basic pads for low-stress, not self-aligning
Additional pad for low-stress, self-aligning
Additional area for IPC reference layout
0.42±0.06
0.50±0.06
2X 1.50 BSC
For Reference Only; not for tooling use (reference JEDEC. TO-243AA)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Active Area Depth, 0.78 mm REF
B
C
Reference land pattern layout (reference IPC7351 SOT89N);
All pads a minimum of 0.20 mm from all adjacent pads;
adjust as necessary to meet application process
requirements and PCB layout tolerances
Branding scale and appearance at supplier discretion
D
Hall element, not to scale
NNT
1
C
Standard Branding Reference View
= Supplier emblem
N = Last two digits of device part number
T = Temperature code
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
11
Chopper-Stabilized, Precision
Hall-Effect Latches
A3280, A3281
and A3283
Package UA, 3-Pin SIP
+0.08
4.09 –0.05
45°
B
C
E
2.06
1.52 ±0.05
1.45 E
Mold Ejector
Pin Indent
+0.08
3.02 –0.05
E
Branded
Face
45°
1
2.16
MAX
D Standard Branding Reference View
= Supplier emblem
N = Last two digits of device part number
T = Temperature code
0.79 REF
A
0.51
REF
NNT
1
2
3
+0.03
0.41 –0.06
15.75 ±0.51
For Reference Only; not for tooling use (reference DWG-9049)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A
Dambar removal protrusion (6X)
B Gate burr area
C Active Area Depth, 0.50 mm REF
+0.05
0.43 –0.07
D
Branding scale and appearance at supplier discretion
E
Hall element, not to scale
1.27 NOM
Copyright ©2002-2010, Allegro MicroSystems, Inc.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the
information being relied upon is current.
Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
12
Similar pages