A6818: DABiC-IV 32-Bit Serial-Input Latched Source Drivers with Active Pull-Downs

A6818
DABiC-IV 32-Bit Serial Input Latched Source Driver
Discontinued Product
This device is no longer in production. The device should not be
purchased for new design applications. Samples are no longer available.
Date of status change: November 1, 2010
Recommended Substitutions:
For existing customer transition, and for new customers or new applications, contact Allegro Sales.
NOTE: For detailed information on purchasing options, contact your
local Allegro field applications engineer or sales representative.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan
for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The
information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
A6818
DABiC-IV 32-Bit Serial Input
Latched Source Driver
Features and Benefits
Description
▪ Controlled output slew rate
▪ 60 V minimum output break down
▪ PNP active pull-downs
▪ Low-power CMOS logic and latches
▪ High-speed data storage
▪ High data-input rate
▪ Low output-saturation voltages
▪ Improved replacements for SN75518N, SN75518NF,
UCN5818x, and UCQ5818x
The A6818 device combines a 32-bit CMOS shift register,
accompanying data latches and control circuitry, with bipolar
sourcing outputs and PNP active pull-downs. Designed
primarily to drive vacuum-fluorescent displays, the 60 V and
–40 mA output ratings also allow this device to be used in
many other peripheral power driver applications. The A6818
features an increased data-input rate (compared with the older
UCN/UCQ5818x) and a controlled output slew rate.
Package: 44 pin PLCC (suffix EP)
The CMOS shift register and latches allow direct interfacing
with microprocessor-based systems. With a 3.3 or 5 V logic
supply, typical serial data-input rates are up to 33 MHz.
A CMOS serial data output permits cascaded connections in
applications requiring additional drive lines. Similar devices
are available as the A6810 (10-bit) and A6812 (20-bit).
The A6818 output source drivers are NPN Darlingtons,
capable of sourcing up to 40 mA. The controlled output slew
rate reduces electromagnetic noise, which is an important
consideration in systems that include telecommunications
and/or microprocessors and to meet government emissions
Not to scale
Continued on the next page…
Functional Block Diagram
V DD
CLOCK
SERIAL
DATA IN
SERIAL-PARALLEL SHIFT REGISTER
STROBE
LATCHES
LOGIC
SUPPLY
SERIAL
DATA OUT
BLANKING
MOS
BIPOLAR
VBB
GROUND
26182.128F
OUT 1 OUT 2 OUT 3
OUT N
LOAD
SUPPLY
Dwg. FP-013-1
DABiC-IV 32-Bit Serial Input
Latched Source Driver
A6818
Description (continued)
regulations. For inter-digit blanking, all output drivers can be
disabled and all sink drivers turned on with a BLANKING input
high. The PNP active pull-downs will sink at least 2.5 mA.
Three temperature ranges are available for optimum performance
in commercial (suffix S-), industrial (E-), and extended industrial
(K-) applications. The package style provided is the minimum-area
surface-mount PLCC (suffix -EP). Copper lead frames, low logic-
power dissipation, and low output-saturation voltages allow these
devices to drive most multiplexed vacuum-fluorescent displays
over the maximum operating temperature range.
The lead (Pb) free versions have 100% matte tin leadframe
plating.
Selection Guide
Part Number
Pb-free
Packing
Ambient Temperature
TA (°C)
Yes
450 pieces/13-in. reel
–40 to 85
–
450 pieces/13-in. reel
–40 to 125
Yes
450 pieces/13-in. reel
–20 to 85
A6818EEPTR-T
A6818KEPTR
A6818SEPTR-T
Absolute Maximum Ratings*
Characteristic
Symbol
Logic Supply Voltage
VDD
Notes
Rating
Units
7.0
V
Driver Supply Voltage
VBB
60
V
Input Voltage Range
VIN
–0.3 to VDD + 0.3
V
Continuous Output Current Range
IOUT
Operating Ambient Temperature
Maximum Junction Temperature
Storage Temperature
–40 to 15
mA
Range E
–40 to 85
ºC
Range K
–40 to 125
ºC
Range S
–20 to 85
ºC
TJ(max)
150
ºC
Tstg
–55 to 125
ºC
TA
*Caution: These CMOS devices have input static protection (Class 2) but are still susceptible to damage if exposed to extremely high
static electrical charges.
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
2
DABiC-IV 32-Bit Serial Input
Latched Source Driver
A6818
Pin-out Diagram
Thermal Characteristics
Characteristic
Package Thermal Resistance
Symbol
Test Conditions*
RθJA
Value Units
1-layer PCB with copper limited to solder pads
54
ºC/W
*Additional thermal information available on the Allegro website.
ALLOWABLE PACKAGE POWER
DISSIPATION IN WATTS
3.0
2.5
2.0
1.5
1.0
SUFFIX 'EP', RQJA = 54oC/W
0.5
0
25
TYPICAL INPUT CIRCUIT
50
75
100
125
AMBIENT TEMPERATURE IN oC
150
TYPICAL OUTPUT DRIVER
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
3
DABiC-IV 32-Bit Serial Input
Latched Source Driver
A6818
TRUTH TABLE
Serial
Shift Register Contents
Data Clock
Input Input I1 I2 I3 ... IN-1 IN
Serial
Data Strobe
Output Input
Latch Contents
I1
I2
I3
...
IN-1
Output Contents
IN Blanklng
I1 I2 I3 ... IN-1 IN
H
H
R1 R2 ...
RN-2 RN-1
RN-1
L
L
R1 R2 ...
RN-2 RN-1
RN-1
X
R1 R2 R3 ...
RN-1 RN
RN
X
X
X
L
R1 R2 R3 ...
RN-1 RN
PN
H
P1 P2 P3 ...
PN-1 PN
L
P1 P2 P3 ... PN-1 PN
X
X
H
L
X
X
...
P1 P2 P3 ...
X
PN-1 PN
X
X
...
X
L
L
... L
L
L = Low Logic Level H = High Logic Level X = Irrelevant P = Present State R = Previous State
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
4
DABiC-IV 32-Bit Serial Input
Latched Source Driver
A6818
ELECTRICAL CHARACTERISTICS at TA = +25°C (A6818S-) or over operating temperature range (A6818Eand A6818K-), VBB = 60 V, unless otherwise noted
Characteristic
Output Leakage Current
Output Voltage
Symbol
ICEX
Test Conditions
VOUT = 0 V
Limits @ VDD = 3.3 V
Limits @ VDD = 5 V
Mln.
Typ.
Max.
Min.
Typ.
Max.
Units
—
<-0.1
-15
—
<-0.1
-15
μA
57.5
58.3
—
57.5
58.3
—
V
VOUT(1)
IOUT = -25 mA
VOUT(0)
IOUT = 1 mA
—
1.0
1.5
—
1.0
1.5
V
Output Pull-Down Current
IOUT(0)
VOUT = 5 V to VBB
2.5
5.0
—
2.5
5.0
—
mA
Input Voltage
VIN(1)
2.2
—
—
3.3
—
—
V
VIN(0)
—
—
1.1
—
—
1.7
V
Input Current
Input Clamp Voltage
Serial Data Output Voltage
Maximum Clock Frequency
Logic Supply Current
IIN(1)
VIN = VDD
—
<0.01
1.0
—
<0.01
1.0
μA
IIN(0)
VIN = 0.8 V
—
<-0.01
-1.0
—
<-0.01
-1.0
μA
IIN = -200 μA
—
-0.8
-1.5
—
-0.8
-1.5
V
VOUT(1)
IOUT = -200 μA
2.8
3.05
—
4.5
4.75
—
V
VOUT(0)
IOUT = 200 μA
—
0.15
0.3
—
0.15
0.3
V
10
33
—
10
33
—
MHz
VIK
fc
IDD(1)
All Outputs High
—
0.25
0.75
—
0.3
1.0
mA
IDD(0)
All Outputs Low
—
0.25
0.75
—
0.3
1.0
mA
IBB(1)
All Outputs High, No Load
—
4.5
9.0
—
4.5
9.0
mA
IBB(0)
All Outputs Low
—
0.2
20
—
0.2
20
μA
tdis(BQ)
CL = 30 pF, 50% to 50%
—
0.7
2.0
—
0.7
2.0
μs
ten(BQ)
CL = 30 pF, 50% to 50%
—
1.8
3.0
—
1.8
3.0
μs
tp(STH-QL)
RL = 2.3 k, CL 30 pF
—
0.7
2.0
—
0.7
2.0
μs
tp(STH-QH)
RL = 2.3 k, CL 30 pF
—
1.8
3.0
—
1.8
3.0
μs
Output Fall Time
tf
RL = 2.3 k, CL 30 pF
2.4
—
12
2.4
—
12
μs
Output Rise Time
tr
RL = 2.3 k, CL 30 pF
2.4
—
12
2.4
—
12
μs
Output Slew Rate
dV/dt
RL = 2.3 k, CL 30 pF
4.0
—
20
4.0
—
20
V/μs
IOUT = ±200 μA
—
50
—
—
50
—
ns
Load Supply Current
Blanking-to-Output Delay
Strobe-to-Output Delay
Clock-to-Serial Data Out Delay tp(CH-SQX)
Negative current is defined as coming out of (sourcing) the specified device terminal.
Typical data is is for design information only and is at TA = +25°C.
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5
DABiC-IV 32-Bit Serial Input
Latched Source Driver
A6818
TIMING REQUIREMENTS and SPECIFICATIONS
(Logic Levels are VDD and Ground)
A. Data Active Time Before Clock Pulse
(Data Set-Up Time), tsu(D) ........................................... 25 ns
B. Data Active Time After Clock Pulse
(Data Hold Time), th(D) ................................................ 25 ns
C. Clock Pulse Width, tw(CH) ................................................. 50 ns
D. Time Between Clock Activation and Strobe, tsu(C) ......... 100 ns
E. Strobe Pulse Width, tw(STH) .............................................. 50 ns
NOTE – Timing is representative of a 10 MHz clock. Significantly
higher speeds are attainable.
Serial Data present at the input is transferred to the shift
register on the logic “0” to logic “1” transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data
information towards the SERIAL DATA OUTPUT. The SERIAL
DATA must appear at the input prior to the rising edge of the
CLOCK input waveform.
Information present at any register is transferred to the
respective latch when the STROBE is high (serial-to-parallel
conversion). The latches will continue to accept new data as long
as the STROBE is held high. Applications where the latches are
bypassed (STROBE tied high) will require that the BLANKING
input be high during serial data entry.
When the BLANKING input is high, the output source drivers are disabled (OFF); the pnp active pull-down sink drivers are
ON. The information stored in the latches is not affected by the
BLANKING input. With the BLANKING input low, the outputs
are controlled by the state of their respective latches.
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
DABiC-IV 32-Bit Serial Input
Latched Source Driver
A6818
Package EP, 44-Pin PLCC
17.53 ±0.13
16.59 ±0.08
0.51
2 1 44
7.75 ±0.36
A
17.53 ±0.13 16.59 ±0.08
7.75 ±0.36
0.74 ±0.08
4.57 MAX
44X
SEATING
PLANE
0.10 C
0.43 ±0.10
C
1.27
7.75 ±0.36
7.75 ±0.36
For Reference Only
(reference JEDEC MS-018 AC)
Dimensions in inches, metric dimensions (mm) in brackets, for reference only
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A Terminal #1 mark area
Copyright ©1998-2008, Allegro MicroSystems, Inc.
The products described here are manufactured under one or more U.S. patents or U.S. patents pending.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the
information being relied upon is current.
Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
Similar pages