The following document contains information on Cypress products. FUJITSU MICROELECTRONICS SUPPORT SYSTEM SS01-71103-1E F2MC-16 Family EMULATOR LQFP-80P PROBE HEADER TYPE 2 MB2147-561-E OPERATION MANUAL PREFACE Thank you for purchasing the LQFP-80P*1 probe header type 2 (MB2147-561-E) for the F2MC*216 family emulator. The LQFP-80P probe header type 2 is used to connect the F2MC-16L/16LX emulator (MB2147-01E)*3 and the F2MC-16L/16LX emulator PGA-299P adapter board (MB2147-20-E)*4 to a user system. That uses FUJITSU F2MC-16LX microcontroller MB90820 series (LQFP-80P). This manual explains the handling of the LQFP-80P probe header type 2 for the F2MC-16 family emulator. Before using the MB2147-561-E, be sure to read this manual. Please contact the sales or support representative for details on the mass production and evaluation MCU models that can be used with this product. *1 : The lead pitch of package (FPT-80P-M05) is 0.5mm and the body size is 12mm × 12mm. Using the product safely. *2 : F2MC is the abbreviation of FUJITSU Flexible Microcontroller. *3 : Referred to as "emulator". *4 : Referred to as "adapter board". ■ Handling and use The handling and use of this product and notes regarding safety are included in the operation manual of the F2MC-16 family emulator. Follow the instructions in for the use of this product. • F2MC-16/16LX EMULATOR MB2147-01-E OPERATION MANUAL • F2MC-16/16LX EMULATOR PGA-299P ADAPTER BOARD MB2147-20-E OPERATION MANUAL ■ European RoHS compliance Products with a -E suffix on the part number are European RoHS compliant products. ■ Notice on this document All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. ■ Caution of the products described in this document The following precautions apply to the product described in this manual. CAUTION Indicates a feature that, if not used correctly, may result in minor or moderate injuries, and which may cause the customer system to malfunction. Cuts This product has parts with sharp points that are exposed. Do not touch edge of the product with your bare hands. Damage When connect the header board to the user system, correctly position the index mark (▲) on the NQPACK mounted on the user system with the index mark (▲) on the header board, otherwise the emulator system and user system might be damaged. Damage When mounting a mass production MCU, correctly position pin 1, otherwise the mass production MCU and user system might be damaged. i • The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. • The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS semiconductor device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. • Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. • The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. • Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. • Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. • The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Copyright ©2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved ii 1. Checking the Delivered Product Before using the LQFP-80P probe header type 2, confirm that the following components are included in the box: :1 • LQFP-80P probe header type 2*1 • Screws for securing header board (M2 × 10mm, 0.4mm pitch) :4 • Washer :4 :1 • NQPACK080SD-ND*2 3 :1 • HQPACK080SD* • Operation manual (Japanese version) :1 • Operation manual (English version, this manual) :1 *1 : Referred to as “header board”. Header board is mounted on YQPACK080SD-4W (Tokyo Eletech Corporation), referred to as “YQPACK”. *2 : IC socket manufactured by Tokyo Eletech Corporation, referred to as “NQPACK”, and supplied with a special screwdriver and 3 guide pins. A socket offering higher reliability, NQPACK080SD-ND-SL (Tokyo Eletech Corporation) (sold separately), can be used by making an IC socket mounting hole on the user system board. For more information, contact Tokyo Eletech Corporation. *3 : IC Socket cover manufactured by Tokyo Eletech Corporation, referred to as “HQPACK”, with 4 screws for securing HQPACK (M2 × 6mm, 0.4mm pitch). This product is used as an emulator system by combining with an optional F2MC-16L/LX emulator and F2MC-16L/LX emulator PGA-299P adapter board (sold separately). Please contact the sales or support representative for details on the adapter that can be used with this product. 2. Handling Precautions The header board is precision-manufactured to improve dimensional accuracy and to ensure reliable contact. The header is therefore sensitive to mechanical shock. To ensure correct use of the header in the proper environment, observe the following points regarding its insertion and removal: • To avoid placing stress on the NQPACK mounted on the user system board during connecting the header board. 1 3. Notes on Designing ■ Restrictions of PC board for the user system Once the header board is connected to the user system, the heights of parts mounted in the space around the header board are restricted. The PC board of the user system must be designed with due consideration given to this restriction (Figure 1). 63mm 28mm 80mm 2 CN2 1 100 99 100 Approx. 13mm* Approx. 35mm* 99 2 FLAT CABLE CN B1 CN3 FLAT CABLE CN B2 CN1 32mm 1 * : The height differs slightly depending on how the YQPACK and the NQPACK are engaged. Figure 1 Header board dimensions 2 0.5mm 0.25mm 2.0mm ■ MCU footprint design notes Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the PC board of the user system. The PC board of the user system must be designed with due consideration given to this footprint as well as to the mass production MCU. For more information, contact the Tokyo Eletech Corporation. 15.1mm 11.1mm No.1 pin Figure 2 Recommended dimensions of the footprint for mounting the NQPACK 3 4. Procedure for Connecting the User System Before using the LQFP-80P probe header type 2, mount the supplied NQPACK on the user system. The header board is used combining the adapter board. To connect the header board to the adapter board, use the flat cable (2 lines) supplied by the emulator sold separately. Refer to the operation manuals of the adapter board about the way to connect. ■ Connecting 1. To connect the header board to the user system, match the index mark (▲) on the NQPACK mounted on the user system with the index mark (▲) on the header board and then insert it (see Figure 3) . The pin of YQPACK is thin and easy to bent. Insert NQPACK after confirm that the pin of YQPACK is not bent. 2. Insert each screw for securing header board in each of the four drilled holes on the header board through a washer, and then first tighten the screws in opposing corners followed by the two remaining screws (see Figure 4) . To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight might result in a defective contact. Flat cable connector NQPACK index (▲) Header board index (▲) Figure 3 Index position 4 Screws for securing header board Washer Header board YQPACK NQPACK User system Figure 4 Header board connection ■ Disconnection To disconnect the header board from the user system, remove all four screws, and then pull the header board straight out of the socket 5 5. Mounting Mass Production MCUs To mount a mass production MCU on the user system, use the supplied HQPACK (see Figure 5). ■ Mounting 1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQPACK mounted on the user system with the index mark (●) on the mass production MCU. 2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, insert the HQPACK into a NQPACK. The pin of HQPACK is thin and easy to bent. Insert NQPACK after confirm that the pin of HQPACK is not bent. 3. Insert each screw for securing HQPACK in each of four drilled holes on the HQPACK, and then first tighten the screws in opposing corners followed by the two remaining screws. To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight might result in a defective contact. Screws for securing HQPACK HQPACK Mass production MCU NQPACK User system Figure 5 Mounting a mass production MCU ■ Disconnection To remove the HQPACK, remove all four screws, and pull out the HQPACK vertically. 6 6. Connector Pin Assignment The header board connects the signals of the evaluation MCU mounted on the adapter board via the flat cable connectors (two) on the header board according to pin information (the same assignments as YQPACK) about the production MCU. For details on the production MCU's pin information, refer to the datasheet or hardware manual for the relevant MCU. ■ Pin assignment Tables 1 and 2 list the pin assignments among the flat cable connector, the evaluation MCU on the adapter board, and the production MCU. For details on the names of signal conductors of the evaluation MCU, refer to the operation manual for the emulator or adapter board. Comments in the tables are given below. *1 : Connected to the main power supply of the evaluation MCU. *2 : Connected to the main power supply (Vcc) of the production MCU. The connection pin numbers are 40 and 60. *3 : Connected to the ground of the evaluation MCU. *4 : Connected to the ground (Vss) of the production MCU. The connection pin numbers are 20 and 61. “ - “ : Unconnected pin (left open). 7 Table 1 Pin assignment of the flat cable connector B1 8 Connector pin numbers Evaluation MCU pin numbers Production MCU pin numbers Connector pin numbers Evaluation MCU pin numbers Production MCU pin numbers 100 98 96 94 92 90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 *3 *3 208 259 79 147 78 *3 146 223 26 94 219 *3 *1 226 275 105 224 *3 274 104 170 227 *3 *3 220 100 97 164 98 *3 23 165 276 108 172 *3 229 130 292 131 247 *3 293 248 133 62 134 *3 *4 *4 2 5 6 8 9 *4 79 *4 *2 *4 71 74 75 62 *4 *4 *4 63 65 66 *4 68 77 *4 12 27 28 30 31 *4 34 36 37 39 41 *4 99 97 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 *3 80 148 *3 207 258 206 77 160 *3 268 269 95 33 169 *3 34 167 35 225 32 *3 106 163 162 96 270 *3 221 273 271 222 99 *3 107 277 109 173 228 *3 193 194 132 *3 61 *3 195 63 294 *3 *4 3 4 *4 7 1 1 80 *4 14 16 26 *4 72 73 *4 76 *2 *4 64 15 67 69 70 *4 78 10 11 13 *2 *4 29 32 33 *4 35 *4 38 42 43 *4 Table 2 Pin assignment of the flat cable connector B2 Connector pin numbers Evaluation MCU pin numbers Production MCU pin numbers Connector pin numbers Evaluation MCU pin numbers Production MCU pin numbers 100 98 96 94 92 90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 *3 *3 267 149 260 209 *3 218 263 153 8 *1 *3 5 103 166 *3 151 *3 6 92 266 91 215 *3 16 264 213 14 203 *3 299 201 141 110 278 *3 *3 *1 252 71 138 *3 296 136 197 250 135 *3 *4 *4 19 *4 *2 *4 *4 *4 *4 *4 25 24 *4 *4 *2 59 57 56 *4 53 50 49 47 46 *4 99 97 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 *3 159 217 *3 81 82 83 87 212 *3 86 150 84 272 168 *3 7 210 261 158 216 *3 157 156 155 88 15 *3 154 255 143 202 142 *3 101 230 262 140 200 *3 199 70 251 198 137 *3 295 64 196 *3 *4 18 *4 *4 *4 *4 *4 *4 19 23 17 21 22 *4 58 55 54 52 51 *4 48 45 44 *4 9 SS01-71103-1E FUJITSU MICROELECTRONICS • SUPPORT SYSTEM F2MC-16 Family EMULATOR LQFP-80P PROBE HEADER TYPE 2 MB2147-561-E OPERATION MANUAL July 2008 the first edition Published FUJITSU MICROELECTRONICS LIMITED Edited Business & Media Promotion Dept.