Category 6A UTP Modular Plug for use with Panduit Patch Cable: PN575B-ENG

Category 6A UTP Modular Plug
for Panduit Patch Cable
T568B & T568A
Part Number: SP6X88P-*
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2013
PN575B
T568B Wiring Scheme
6
4
3
2
7
5
1
GRN/
BRN/
BLU/
ORG/
T568B BRN WHT GRN WHT BLU WHT ORG WHT
Pin #
8
Strain Relief Boot
Specifications
Strain Relief Collar
• Cable jacket diameter 0.285 in. max.
• Maximum conductor insulation diameter 0.041 in.
• Panduit recommends T568B wiring scheme for use
with cable constructed with the brown pair opposing
the orange pair.
Divider
Load Bar
Plug Housing
Load Bar
Divider
Conductor holes and Contact slots
Conductor slots and “V” channel
1
Pins
8
Conductor holes
“V” channel
Contact slots
1
Divider post


CWST
Thread on boot
and collar first!
(Cable ends 1 & 2)



90°
(Cable end 2)
2
BLU

Note orientation of the divider depending on cable end 1
or cable end 2. The “V” channel should be aligned with the
green pair.

Insert divider posts into the cable. If the cable has an
internal spline, insert divider posts into the brown and
orange quadrants of the spline.

Arrange conductors to T568B wiring scheme while
minimizing untwist and smooth conductors.

Seat conductors into proper divider slots while holding
divider near the end of the cable jacket.
(Cable end 1)
GRN
ORG
“V” channel
ORG
“V” channel
GRN
Thread boot and collar onto the cable first.
Remove 2.0" of the outer jacket from the cable end using
wire stripping tool (CJAST).
Remove matrix foil to expose twisted pairs.
Fan twisted pairs into respective quadrants. The brown
pair should be opposite the orange pair.
When a cable spline (X-shaped filler) is present, cut spline
flush to fanned pairs using wire snipping tool (CWST).
BRN
BLU
3
BRN
“V” channel
(Cable end 1)
(Cable end 2)
* Denotes packaging quantity.
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 1 of 4
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2013
4

While holding conductors in respective divider slots,
straighten and align untwisted conductors using a circular
motion.

Do not release grip of conductors until load bar is applied
in order to maintain conductor alignment.

Trim conductors on an angle approximately 1.00" from
divider leading edge.

Orient load bar with contact slots facing downward.

Guide conductors into load bar holes while holding
conductors in the divider.

Slide load bar towards divider until flush.

Ensure the divider/load bar is centered and perpendicular
to the cable axis.

Trim conductors flush with load bar face.

While holding load bar and divider stationary, slide collar
and boot forward until there is no gap between collar and
divider. Do not exert pressure onto divider as collar can
push load bar off conductors.

Confirm orientation of collar.

Align pin #1 of cable sub-assembly with pin #1 of plug
housing.

Grip and squeeze across collar arms as sub-assembly
is inserted into plug housing.

Push sub-assembly into housing until collar locking tabs
clear the plug housing pocket. Although not required, TX6
PLUS Plug Assembly Tool (CSPT) is available to facilitate
this step.

Slide boot forward and fully seat onto strain relief collar.

Use tool MPT5-8AS to complete termination.

Assembly is complete. Visually check plug.
8
6
4
3
2
7
5
1
GRN/
BRN/
BLU/
ORG/
T568B BRN WHT GRN WHT BLU WHT ORG WHT
Pin #
PN575B
1.00"
(Cable end 1)
5
(Cable end 2)
Verify
Load Bar
orientation
(Cable end 1)
1
8
Pins
1
Pins
6
8
7
(Cable end 1)
(Cable end 2)
8
1
Pins
Collar locking
tabs
8
1
(Cable end 1)
Pins
9
8
10
MPT5-8AS
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 4
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2013
PN575B
T568A Wiring Scheme
6
4
3
2
7
5
1
ORG/
BRN/
BLU/
GRN/
T568A BRN WHT ORG WHT BLU WHT GRN WHT
Pin #
Strain Relief Boot
8
Specifications
• Cable jacket diameter 0.285 in. max.
• Maximum conductor insulation diameter 0.041 in.
• Panduit recommends T568A wiring scheme for use
with cable constructed with the brown pair opposing
the green pair.
Strain Relief Collar
Divider
Load Bar
Plug Housing
Load Bar
Divider
Conductor holes and Contact slots
Conductor slots and “V” channel
1
Pins
8
Conductor holes
“V” channel
Contact slots
1


CWST
Thread on Boot
and Collar first!


(Cable ends 1 & 2)

90°
2
(Cable end 2)
Note orientation of the divider depending on cable end 1
or cable end 2. The “V” channel should be aligned with the
orange pair.

Insert divider posts into the cable. If the cable has an
internal spline, insert divider posts into the brown and
green quadrants of the spline.

Arrange conductors to T568A wiring scheme while
minimizing untwist and smooth conductors.

Seat conductors into proper divider slots while holding
divider near the end of the cable jacket.
(Cable end 1)
ORG
“V” channel
GRN
“V” channel
ORG
Thread boot and collar onto the cable first.
Remove 2.0" of the outer jacket from the cable end using
wire stripping tool (CJAST).
Remove matrix foil to expose twisted pairs.
Fan twisted pairs into respective quadrants. The brown
pair should be opposite the green pair.
When a cable spline (X-shaped filler) is present, cut spline
flush to fanned pairs using wire snipping tool (CWST).

BLU
GRN
Divider post
BRN
BLU
3
BRN
“V” channel
(Cable end 1)
(Cable end 2)
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 4
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2013
4
7
5
1
6
4
3
2
BRN/
BLU/
GRN/
ORG/
T568A BRN WHT ORG WHT BLU WHT GRN WHT
1.00"

While holding conductors in respective divider slots,
straighten and align untwisted conductors using a circular
motion.

Do not release grip of conductors until load bar is applied
in order to maintain conductor alignment.

Trim conductors on an angle approximately 1.00" from
divider leading edge.

Orient load bar with contact slots facing downward.

Guide conductors into load bar holes while holding
conductors in the divider.

Slide load bar towards divider until flush.

Ensure the divider/load bar is centered and perpendicular
to the cable axis.

Trim conductors flush with load bar face.

While holding load bar and divider stationary, slide collar
and boot forward until there is no gap between collar and
divider. Do not exert pressure onto divider as collar can
push load bar off conductors.

Confirm orientation of collar.

Align pin #1 of cable sub-assembly with pin #1 of plug
housing.

Grip and squeeze across collar arms as sub-assembly
is inserted into plug housing.
Push sub-assembly into housing until collar locking tabs
clear the plug housing pocket. Although not required, TX6
PLUS Plug Assembly Tool (CSPT) is available to facilitate
this step.
Slide boot forward and fully seat onto strain relief collar.
Use tool MPT5-8AS to complete termination.
Assembly is complete. Visually check plug.
8
Pin #
PN575B
(Cable end 1)
5
(Cable end 2)
Verify
Load Bar
orientation
(Cable end 1)
1
Pins
8
1
Pins
6
8
7
(Cable end 1)
8
(Cable end 2)
1
Pins
Collar locking
tabs
8
1
Pins
9
(Cable end 1)
8
10
MPT5-8AS




E-mail:
[email protected]
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
Page 4 of 4
Phone:
866-405-6654
Similar pages