0.2MB

The following document contains information on Cypress products.
FUJITSU MICROELECTRONICS
SUPPORT SYSTEM
SS01-71127-1E
DSU-FR EMULATOR
LQFP-100P HEADER TYPE 5
MB2198-129-E
OPERATION MANUAL
PREFACE
Thank you for purchasing the LQFP-100P header type 5 (MB2198-129-E) for the DSU-FR emulator.
The LQFP-100P header type 5 is used to connect the DSU-FR emulator (MB2198-01-E)*1 and the
DSU-FR emulator PGA-401P adapter type 2 (MB2198-130-E)*2 to a user system. That uses FUJITSU MICROELECTRONICS FR*3 family microcontroller MB91270 series (LQFP-100P)*4.
This manual explains the handling of the LQFP-100P header type 5 for the DSU-FR emulator. Before
using the MB2198-129-E, be sure to read this manual.
Please contact the sales or support representative for details on the mass production and evaluation
MCU models that can be used with this product.
*1 : referred to as "emulator"
*2 : referred to as "adapter board"
*3 : FR, the abbreviation of FUJITSU RISC controller, is a line of products of FUJITSU MICROELECTRONICS LIMITED.
*4 : The lead pitch of PACKAGE (FPT-100P-M05) is 0.5 mm and the body size is 14 mm × 14 mm.
■ Handling and Use
The handling and use of this product and notes regarding safety are included in the operation manual
of the DSU-FR emulator.
Follow the instructions in for the use of this product.
• DSU-FR EMULATOR MB2198-01-E OPERATION MANUAL
• DSU-FR EMULATOR PGA-401P ADAPTER TYPE 2
MB2198-130-E OPERATION MANUAL
■ European RoHS Compliance
Products with a -E suffix on the part number are European RoHS compliant products.
■ Notice on this Document
All information included in this document is current as of the date it is issued. Such information is
subject to change without any prior notice.
Please confirm the latest relevant information with the sales representatives.
■ Caution of the Product Described in this Document
The following precautions apply to the product described in this manual.
CAUTION
Indicates a feature that, if not used correctly, may result in minor or moderate
injuries, and which may cause the customer system to malfunction.
Cuts
This product has parts with sharp points that are exposed.
Do not touch edge of the product with your bare hands.
Damage
When connect the header board to the user system, correctly position the index
mark (▲) on the NQPACK mounted on the user system with the index mark (▲)
on the header board, otherwise the emulator system and user system might be
damaged.
Damage
When mounting a mass production MCU, correctly position pin 1, otherwise the
mass production MCU and user system might be damaged.
i
• The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
• The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS semiconductor device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to
use based on such information. When you develop equipment incorporating the device based on such information, you
must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes
no liability for any damages whatsoever arising out of the use of the information.
• Any information in this document, including descriptions of function and schematic diagrams, shall not be construed
as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right
of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third
parties which would result from the use of information contained herein.
• The products described in this document are designed, developed and manufactured as contemplated for general use,
including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not
designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air
traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2)
for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims
or damages arising in connection with above-mentioned uses of the products.
• Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from
such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions.
• Exportation/release of any products described in this document may require necessary procedures in accordance with
the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
• The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Copyright ©2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
ii
1. Checking the Delivered Product
Before using the LQFP-100P header type 5, confirm that the following components are included in
the box:
:1
• LQFP-100P header type 5*1
• Screws for securing header board (M2 × 10mm, 0.4mm pitch)
:4
• Washer
:4
:1
• NQPACK100SD-ND*2
3
:1
• HQPACK100SD*
• Operation manual (Japanese version)
:1
• Operation manual (English version, this manual)
:1
*1 : Referred to as “header board”. Header board is mounted on YQPACK100SD-4W (Tokyo
Eletech Corporation), referred to as “YQPACK”.
*2 : The IC socket (manufactured by Tokyo Eletech Corporation and referred to as the “NQPACK”)
which is supplied with a screwdriver and 3 guide pins. The more reliable NQPACK100SD-NDSL socket (Tokyo Eletech Corporation, sold separately) can be used by fabricating IC socket
mounting holes in the user system board. For more information, contact Tokyo Eletech Corporation.
*3 : The IC socket cover (manufactured by Tokyo Eletech Corporation and referred to as the “HQPACK”).
Includes 4 screws for securing the HQPACK (M2 × 6mm, 0.4mm pitch).
This product is used as an emulator system by combining with an optional emulator and adapter
board.
Please contact the sales or support representative for details on the emulator and the adapter board
that can be used with this product.
2. Handling Precautions
The header board is precision-manufactured to improve dimensional accuracy and to ensure reliable
contact. The header is therefore sensitive to mechanical shock. To ensure correct use of the header
in the proper environment, observe the following points regarding its insertion and removal:
• To avoid placing stress on the NQPACK mounted on the user system board during connecting
the header board.
1
3. Notes on Designing
■ Restrictions of PC board for the user system
Once the header board is connected to the user system, the heights of parts mounted in the space
around the header board are restricted.
The PC board of the user system must be designed with due consideration given to this restriction
(Figure 1).
78mm
32mm
B
B1
CN3
B50A50
80mm
CN2
A50
S2
CN1
S1
B1 A1
B50
Approx. 35mm*
Approx.
13mm*
36mm
A1
A
* : The height differs slightly depending on how the YQPACK and the NQPACK are
engaged.
Figure 1 Header board dimensions
2
■ MCU footprint design notes
Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the PC board
of the user system.
The PC board of the user system must be designed with due consideration given to this footprint as
well as to the mass production MCU.
For more information, contact the Tokyo Eletech Corporation.
0.5mm × 24 = 12mm
0.25mm
13.0mm
5.8mm
φ2.2mm*2
3-φ1.0mm*1
0.5mm × 24 = 12mm
2.0mm
0.5mm
2.0mm
No.1
pin
5.8mm
13.0mm
2.0mm
2.0mm
*1 : The positions of the holes (φ1.0mm) for the guide pins when the NQPACK is mounted. These holes are
not needed if the guide pins are not used.
*2 : The position of the screw hole (φ2.2mm) used to affix the IC socket when the NQPACK100SD-ND-SL
(Tokyo Eletech Corporation, sold separately) is mounted.
This hole is not needed if the NQPACK100SD-ND-SL is not used.
Figure 2 Recommended dimensions of the footprint for mounting the NQPACK
3
4. Procedure for Connecting to the User System
Before using the LQFP-100P header type 5, mount the supplied NQPACK on the user system.
The header board is used combining the emulator. Moreover, connection of a header board and
an adapter board is two flat cables (a standard or Long) appended to the adapter board. Please use it.
Refer to the operation manuals of the emulator or the adapter board about the way to connect.
■ Connecting
1. To connect the header board to the user system, match the index mark (▲) on the NQPACKmounted on the user system with the index mark (▲) on the header board and then insert it (See
Figure 3) . The pin of YQPACK is thin and easy to bent. Check that the YQPACK pins are not
bent before inserting the YQPACK into the NQPACK.
2. Insert each of the screws for securing the header board through a washer and into each of the four
holes in the header board. To tighten the screws, use the screwdriver supplied with the NQPACK
to evenly tighten the diagonally opposite screws in turn (see Figure 4).
Be careful to avoid overtightening the screws as this may cause a bad connection.
Adapter board connector A
Adapter board connector B
YQPACK
(It mounts in the back)
NQPACK index (▲)
Header board index (▲)
Figure 3 Index position
4
Screws for securing
header board
Washer
Header board
YQPACK
NQPACK
User system
Figure 4 Header board connection
■ Disconnection
To disconnect the header board from the user system, remove all four screws, and then pull the header board straight out of the NQPACK.
5
5. Mounting Mass Production MCUs
To mount a mass production MCU on the user system, use the supplied HQPACK.
■ Mounting
1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQPACK mounted on the user system with the index mark (●) on the mass production MCU.
2. Confirm that the mass production MCU is correctly mounted on the NQPACK and then align the
index mark on the HQPACK with the index mark on the NQPACK (the corner with an angle cut
out of it) and insert the HQPACK into the NQPACK (see Figure 5).
The HQPACK pins are thin and easy to be bent. Check that the HQPACK pins are not bent before
inserting it into the NQPACK.
3. Insert the screws for securing the HQPACK into the four holes in the HQPACK, and then evenly
tighten the diagonally opposite screws in turn using the screwdriver that was included with the
NQPACK. Be careful to avoid overtightening the screws as this may cause a bad connection.
Screws for securing HQPACK
HQPACK
Mass production MCU
NQPACK
User system
Figure 5 Mounting a mass production MCU
■ Disconnection
To remove the HQPACK, remove all four screws, and pull out the HQPACK vertically.
6
6. Connector Pin Assignment
The signals from the evaluation MCU that is mounted on the adapter board are connected to the YQPACK (which has the same pin configuration as the production MCU) via adapter board connectors
A and B on the header board.
The adapter board and header board are connected using the 2 flat cables (standard or long) that are
included with the adapter board. See the operation manual for the adapter board for details on how
to connect the flat cables.
See the data sheet or hardware manual of each of the mass production MCUs for details on the MCU
pins.
■ Pin assignment
Tables 2 and 3 list the corresponding pin assignments for adapter board connectors A and B, the evaluation MCU on the adapter board, and the production MCU.
See the operation manual of the adapter board for details on the evaluation MCU pin names.
The notes in the tables have the following meanings:
*1 :
*2 :
*3 :
*4 :
*5 :
Connected to the mass production MCU pin:VSS (pins 14, 42, 64 and 89).
Connected to the mass production MCU pin:C (pin15).
Connected to the mass production MCU pin:VCC (pins 13, 63 and 83).
Header board control pin (not connected to the mass production MCU pins).
The evaluation MCU pins (pins 38, 51, 87, and 209) are selected with a jumper plug on the
header board, and connected with mass production MCU pins (pins 11 and 12).
Evaluation MCU
Mass production MCU
S1
38 pin
A
B
51 pin
12 pin
C
S2
87 pin
A
B
209 pin
11 pin
C
Figure 6 Pin assignment
Table 1 Jumper plug setup
Jumper plug setup (S1,S2) item
Mass production MCU
A-B
MB91F272
B-C
MB91F272R
*6 : It connects with the pull-up (10kΩ) because it becomes non-connected terminal in evaluation
MCU.
*7 : It connects with the pull-down (10kΩ) because it becomes non-connected terminal in evaluation MCU.
7
Connector
pin numbers
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
8
Table 2 Pin assignment of the adapter board connector A
Evaluation
Mass production
Evaluation
Connector
MCU
MCU
MCU
pin numbers
pin numbers
pin numbers
pin numbers
VSS
*1
B1
VSS
135
*6
B2
84
301
*6
B3
192
191
*6
B4
35
349
*6
B5
131
296
31
B6
242
186
33
B7
245
188
35
B8
297
244
37
B9
346
187
39
B10
345
243
41
B11
VSS
83
73
B12
300
*2
B13
248
249
62
B14
193
VSS
*1
B15
85
302
59
B16
36
136
57
B17
303
37
55
B18
86
138
21
B19
VSS
250
19
B20
351
195
17
B21
137
38
*5
B22
194
VSS
*1
B23
5
B24
87
209
*5
B25
51
252
71
B26
251
39
70
B27
VSS
40
8
B28
304
139
2
B29
88
41
9
B30
305
VSS
*1
B31
89
140
4
B32
196
42
67
B33
253
306
66
B34
197
65
B35
VSS
141
3
B36
90
76
*3
B37
202
310
*6
B38
201
VSS
*1
B39
357
257
*6
B40
144
309
*6
B41
256
200
*6
B42
356
308
*6
B43
VSS
92
*6
B44
44
255
*6
B45
143
199
*6
B46
307
91
96
B47
254
98
B48
142
198
100
B49
43
VSS
*1
B50
VSS
Mass production
MCU
pin numbers
*1
*6
*6
*6
30
32
34
36
38
40
*1
74
*6
*6
61
60
58
56
*1
20
18
16
*2
*5
*5
69
*1
*3
7
1
6
5
68
*2
*1
10
*6
*6
*6
*6
*6
*6
*1
*6
*6
95
*2
97
99
*1
Connector
pin numbers
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
Table 3 Pin assignment of the adapter board connector B
Evaluation
Mass production
Evaluation
Connector
MCU
MCU
MCU
pin numbers
pin numbers
pin numbers
pin numbers
VSS
*1
B1
VSS
B2
50
4
*6
B3
315
208
*6
B4
98
153
*6
B5
182
127
*6
B6
239
VSS
*1
B7
31
293
*6
B8
183
78
*6
B9
128
184
*6
B10
32
240
*6
B11
VSS
129
*6
B12
79
294
53
B13
185
130
47
B14
241
VSS
*1
B15
97
80
45
B16
295
*3
B17
344
298
29
B18
132
189
27
B19
VSS
246
26
B20
348
299
24
B21
133
81
22
B22
33
VSS
*1
B23
247
190
*6
B24
34
134
*6
B25
82
*3
B26
29
291
90
B27
VSS
258
94
B28
146
203
92
B29
259
93
86
B30
147
VSS
*1
B31
204
312
83
B32
260
94
81
B33
45
205
79
B34
148
1
77
B35
VSS
*3
B36
95
46
75
B37
126
292
51
B38
30
VSS
*1
B39
77
206
*3
B40
261
47
*1
B41
313
2
*1
B42
149
150
B43
VSS
262
*1
B44
48
96
*1
B45
151
207
B46
49
VSS
*1
B47
3
263
*7
B48
264
*7
B49
VSS
*1
B50
VSS
Mass production
MCU
pin numbers
*1
*6
*6
*6
*6
72
*6
*6
*6
*1
54
48
46
*1
44
43
28
*1
25
23
*3
*6
*6
*6
91
*1
93
87
85
84
82
80
78
*1
76
52
50
49
*1
*1
*1
*1
*3
*1
9
SS01-71127-1E
FUJITSU MICROELECTRONICS • SUPPORT SYSTEM
DSU-FR EMULATOR
LQFP-100P HEADER TYPE 5
MB2198-129-E
OPERATION MANUAL
September 2008 the first edition
Published FUJITSU MICROELECTRONICS LIMITED
Edited
Business & Media Promotion Dept.
Similar pages