Datasheet

For more information, please visit the product page.
date
06/28/2011
page
1 of 3
SERIES: SJ-3502-SMT │ DESCRIPTION: MID MOUNT POWER JACK
FEATURES
•mid mount for low profile applications
•shielded
•no internal switches
RoHS
SPECIFICATIONS
parameter
conditions/description
min
rated input voltage
typ
rated input current
contact resistance
between
after life
between
after life
insulation resistance
at 500 Vdc
at 500 Vdc, after environmental tests
voltage withstand
at 50/60Hz for 1 minute
insertion/withdrawl force
terminal strength
terminal and mating plug
test, between terminal and mating plug
terminal in a closed circuit1
test, between terminal in a closed circuit1
after life test
units
Vdc
1
A
50
100
30
60
mΩ
mΩ
mΩ
mΩ
100
50
MΩ
MΩ
0.3
0.2
any direction for 10 seconds
operating temperature
Notes:
max
12
-25
500
Vac
3
2
kg
kg
500
g
85
°C
1. When measured at a current of less than 100 mA / 1 kHz
TESTING
parameter
conditions/description
min
typ
max
units
solderability
95% solder coverage on lead, neutral flux, 2 sec.
250
255
260
°C
reflow soldering
see graph
life
at 24 insertion/withdrawl cycles per minute
heat
the relative test before and after testing should
comply with the Insulation Resistance section
83
cold
the relative test before and after testing should
comply with the Insulation Resistance section
33
humidity
the relative test before and after testing should
comply with the Insulation Resistance section
38
Notes:
5,000
85
87
50
°C
%RH
hours
35
96
37
°C
hours
40
96
42
°C
hours
%RH
96
90
cycles
95
All measurements and test shall be made at a temperature 10°C to 35°C with a relative humidity of 45% RH to 85% RH under the standard atmospheric pressure unless
otherwise specified.
cui.com
For more information, please visit the product page.
CUI Inc │ SERIES: SJ-3502-SMT │ DESCRIPTION: MID MOUNT POWER JACK
date 06/28/2011 │ page 2 of 3
REFLOW SOLDERING
270
260
250
240
217
180
120
120
60
50
°C
70
60
140
120
250
180
340
240
300
380
360
430
420
480
Time (second)
MECHANICAL DRAWING
units: mm[inches]
9.9 0.390
MATERIAL
PLATING
terminal 1
stainless steel
silver
terminal 2
copper alloy
silver
terminal 3
copper alloy
silver
plastic
PA6T
0.3
3.600 0.142
7.1 0.280
4.50 0.177
6.2 0.244
A
0.50 0.020
(6 PLCS)
COPLANARITY
0.1
4.15 0.163
-
2.00 0.079
MODEL NO.
0.95 0.037
(4 PLCS)
+0.2
-0.1
SJ-3502-SMT
1
3
SCHEMATIC
2.95 0.116
5.90 0.232
2
8.45 0.333
+
DETAIL A
SCALE 12 : 1
0.3
12.7 0.500
2.00 0.079
3.20X1.30
(4 PLCS)
5.6 0.220
12.5 0.492
2.40X0.50
(4 PLCS)
1
4.20 0.165
2
1
3.40 0.134
6.10 0.240
9.0 0.354
(2 PLCS)
5.6 0.220
(2 PLCS)
1
2
1
3.40 0.134
4.20 0.165
2.2 0.087
(2 PLCS)
1
2.2 0.087
(2 PLCS)
TOLERANCE:
X.X ±0.2mm
X.XX ±0.1mm
X.XXX ±0.05mm
3
9.0 0.354
(2 PLCS)
1
2.50X2.10
(2 PLCS)
PCB LAYOUT
TOP VIEW
C, 0.55
1
3
0.45 0.018
(4 PLCS)
1
2.00 0.079
(6 PLCS)
cui.com
For more information, please visit the product page.
CUI Inc │ SERIES: SJ-3502-SMT │ DESCRIPTION: MID MOUNT POWER JACK
date 06/28/2011 │ page 3 of 3
REVISION HISTORY
rev.
1.0
description
date
initial release
06/28/2011
The revision history provided is for informational purposes only and is believed to be accurate.
Headquarters
20050 SW 112th Ave.
Tualatin, OR 97062
800.275.4899
Fax 503.612.2383
cui.com
[email protected]
CUI offers a one (1) year limited warranty. Complete warranty information is listed on our website.
CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is
assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use.
CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to
affect its safety or effectiveness.
Similar pages