Datasheet

G9EC-1
DC Power Relays (200-A Models)
DC Power Relays Capable of
Interrupting High-voltage, High-current
Loads
• A compact relay (98 x 44 x 86.7 mm (L x W x H)) capable of switching 400-V
200-A DC loads. (Capable of interrupting 1,000 A at 400 VDC max.)
• The switching section and driving section are gas-injected and hermetically
sealed, allowing these compact relays to interrupt high-capacity loads. The
sealed construction also requires no arc space, saves space, and helps ensure
safe applications.
• Downsizing and optimum design allow no restrictions on the mounting
direction.
• Terminal Cover is also available for industrial applications.
• UL/CSA standard UL508 approved.
RoHS Compliant
Refer to "DC Power Relays Common Precautions".
■Model Number Legend
G 9 E C -@ -@ -@ -@
— — — —
2
3
4
2. Contact Form
Blank: SPST-NO
-
1
1. Number of Poles
1: 1 pole
G
9
E
C
1
3. Coil Terminals
B : M3.5 screw terminals (standard)
Blank: Lead wire output
4. Special Functions
■List of Models
Terminals
Models
Coil terminals
Contact terminals
Contact form
Coil rated voltage
SPST-NO
12 VDC
24 VDC
48 VDC
60 VDC
100 VDC
Screw terminals
Switching/current
conduction models
Screw terminals
Lead wire
Model
G9EC-1-B
G9EC-1
Note 1. Two M8 nuts are provided for the contact terminal connection.
Note 2. Two M3.5 screws are provided for the coil terminal connection.
■Ratings
●Coil
Item
Rated voltage
Rated current
(mA)
Coil resistance
(Ω)
12 VDC
938
24 VDC
469
51.2
48 VDC
234
204.8
60 VDC
188
320.0
100 VDC
113
888.9
Must-operate voltage Must-release voltage
(V)
(V)
Maximum voltage
(V)
Power consumption
(W)
110% of rated
voltage (at 23°C
within 10 minutes)
Approx. 11
12.8
75% max. of rated
voltage
8% min. of rated
voltage
Note 1. The figures for the rated current and coil resistance are for a coil temperature of 23°C and have a tolerance of ±10%.
Note 2. The figures for the operating characteristics are for a coil temperature of 23°C.
Note 3. The figure for the maximum voltage is the maximum voltage that can be applied to the relay coil.
●Contacts
Item
Rated load
Resistive load
G9EC-1(-B)
200 A at 400 VDC
Rated carry current
200 A
Maximum switching voltage
400 V
Maximum switching current
200 A
1
G9EC-1
DC Power Relays (200-A Models)
■Characteristics
Item
Model
Contact resistance *1
Contact voltage drop
0.1 V max. (for a carry current of 200 A)
Operate time
50 ms max.
Release time
Insulation
resistance *2
Dielectric strength
30 ms max.
Between coil and
contacts
1,000 MΩ min.
Between contacts of
the same polarity
1,000 MΩ min.
Between coil and
contacts
2,500 VAC, 1 min
Between contacts of
the same polarity
2,500 VAC, 1 min
Impulse withstand voltage *3
Vibration
resistance
Shock resistance
4,500 V
Destruction
10 to 55 to 10 Hz 0.75-mm single amplitude (Acceleration: 2.94
to 88.9 m/s2)
Malfunction
10 to 55 to 10 Hz 0.75-mm single amplitude (Acceleration: 2.94
to 88.9 m/s2)
Destruction
490 m/s2
Malfunction
196 m/s2
Mechanical endurance *4
-
G
9
E
C
1
G9EC-1(-B)
30 mΩ max. (0.2 mΩ typical)
200,000 operations min.
Electrical endurance (resistive load) *5
400 VDC, 200 A, 3,000 operations min.
Short-time carry current
300 A (15 min)
Maximum interruption current
1,000 A at 400 VDC (10 times)
Overload interruption
700 A at 400 VDC (40 times min.)
Reverse polarity interruption
-200 A at 200 VDC (1,000 times min.)
Ambient operating temperature
-40 to 50°C (with no icing or condensation)
Ambient operating humidity
5% to 85%
Weight (Including accessories)
Approx. 560 g
Note. The above values are initial values at an ambient temperature of 23°C unless otherwise specified.
*1. The contact resistance was measured with 1 A at 5 VDC using the voltage drop method.
*2. The insulation resistance was measured with a 500-VDC megohmmeter.
*3. The impulse withstand voltage was measured with a JEC-212 (1981) standard impulse voltage waveform (1.2 x 50 μs).
*4. The mechanical endurance was measured at a switching frequency of 3,600 operations/hr.
*5. The electrical endurance was measured at a switching frequency of 60 operations/hr.
2
G9EC-1
DC Power Relays (200-A Models)
■Engineering Data
Operations (× 104
1,000
500
300
100
DC resistive load
50
30
10
5
3
10
5
Switching
400-VDC
resistive load
(positive direction)
3
1,000
500
300
1
100
0.5
50
0.3
30
0.1
10
1
0.05
5
0.5
0.3
0.03
3
0.1
30
50
100
300
●Carry Current vs Energizing Time
10
30
50
100
10,000
300
10
500 1,000
50
100
●Must-operate Voltage and
Must-release Voltage Distributions
1,000
30
Sample: G9EC-1
Number: 35
Must-operate voltage
Must-release voltage
25
20
500 1,000
10,000
Switching current (A)
Switching current (A)
Number of Relays
100,000
Interrupting
400-VDC
resistive load
(positive direction)
1
0.01
500 1,000
Switching voltage (V)
●Time Characteristic Distributions
Number of contacts
10
Energizing time (s)
●Electrical Endurance (Interruption
Performance)
Operations
卐
Switching current (A)
G9EC-1(-B) Switching/Current Conduction Models
●Maximum Switching Capacity
●Electrical Endurance (Switching
Performance)
30
Sample: G9EC-1
Number: 32
Operate time
Release time
25
20
15
15
10
10
5
5
G
9
E
C
1
100
-
10
100
300
500
0
700 1,000
10
20
Sample: G9EC-1
Number: 5
Unconfirmed area
0.8
0.7
5.0
4.0
60
70
80
0
0.0
2.0
4.0
6.0
8.0 10.0 12.0 14.0 16.0 18.0
Time (ms)
Sample: G9EC-1
Number: 5
3.0
2.0
0.6
1.0
0.5
0.0
Must-release voltage
Must-operate voltage
Confirmed area
0.4
50
●Vibration Resistance
Rate of change (%)
Single amplitude (mm)
1
0.9
40
Percentage of rated voltage (%)
Carry current (A)
●Vibration Malfunction
30
-1.0
0.3
-2.0
0.2
-3.0
0.1
-4.0
-5.0
0
1
3
5
10
30
50
100
Start
After test
Characteristics were measured after applying vibration
at a frequency of 10 to 55 Hz (single amplitude of 0.75
mm) to the test piece (not energized) for 2 hours each
in 3 directions. The percentage rate of change is the
average value for all of the samples.
Frequency (Hz)
Unit: m/s2
Sample: G9EC-1
Number: 5
●Shock Resistance
T:
TAC VDC
-1-BCONA 400
ECC 200
AN
1
G9VDJAP
-000
12 IN
2K1
136
1,000
E
MAD
Lot
Z
No.
X
800
Y'
Y
600
X
Z'
)
1(+
)
2(-
Y
Z
X'
Rate of change (%)
●Shock Malfunction
5.0
4.0
Sample: G9EC-1
Number: 5
3.0
2.0
400
1.0
200
0.0
Must-operate voltage
Must-release voltage
㸫1.0
200
Z'
Deenergized
㸫2.0
400
X'
600
㸫4.0
800
1,000
Y'
㸫3.0
Energized
The value at which malfunction occurred
was measured after applying shock to the
test piece 3 times each in 6 directions
along 3 axes.
㸫5.0
Start
After test
Characteristics were measured after applying a shock
of 490 m2/s to the test piece 3 times each in 6
directions along 3 axes. The percentage rate of
change is the average value for all of the samples.
3
G9EC-1
DC Power Relays (200-A Models)
■Dimensions (Unit: mm)
●Models with Screw Terminals
G9EC-1-B
Terminal Arrangement/
Internal Connections
(TOP VIEW)
1 (+)
7
32
44
2-M3.5
2 (−)
1
(+)
2
:
CT DC
TA 0V
BN 0
-1- C0O0A 4
EC 2
G9VDJACPAN
01
-00
K1
1A2DE IN
62
13
M
tN
7
28.6
)
2(−
o.
Lo
98
Mounting Hole Dimensions
(TOP VIEW)
2-M8
26
1(+)
86.7
68.6
(Terminal
height)
G9EC-1-B
12VDC CONTACT:
200A 400VDC
8
MADE IN JAPAN
44.2
(Coil
terminal
height)
Dimension (mm) Tolerance (mm)
10 or lower
±0.3
10 to 50
±0.5
50 or higher
±1
Two, M6 or 6.5-dia. holes
26.7
2(−)
7
8
Note: Be sure to connect terminals with the correct
polarity. Coils do not have polarity.
72
86
Two, 6.2-dia. holes
86±0.1
Lot No. 1362K1-0001
10.5
32±0.1
●Models with Lead Wires
G G9EC-1
9
E
C
1
Terminal Arrangement/
Internal Connections
(TOP VIEW)
1 (+)
32
44
-
2 (−)
)
1(+
2
)
2(−
M
tN
7
28.6
:
CT DC
TA 0V
BN 0
-1- C0O0A 4
EC 2
G9VDJACPAN
01
-00
K1
1A2DE IN
62
13
o.
Lo
98
26
(10)
2-M8
230±20
Two, M6 or 6.5-dia. holes
1(+)
G9EC-1
12VDC
8
Mounting Hole Dimensions
(TOP VIEW)
26.7
2(−)
7
8
Note: Be sure to connect terminals with the correct
polarity. Coils do not have polarity.
72
86
Two, 6.2-dia. holes
MADE IN JAPAN
86.7
68.6
(Terminal
height)
CONTACT:
200A 400VDC
86±0.1
Lot No. 1362K1-0001
Dimension (mm) Tolerance (mm)
10 or lower
±0.3
10 to 50
±0.5
50 or higher
±1
10.5
32±0.1
■Options (Unit: mm)
●Terminal Cover
P9EC-C
* Dimensions of cutout for wiring.
Note: Be sure to remove the cutouts
for wiring that are located in the
wiring outlet direction before
installing the Terminal Cover.
44
P9
MA
DE
IN
EC
-C
JA
PA
N
>P
C<
CCE
9
NA
PA
JN
<C
P>
IE
P
DA
18
M
28
*
28
74
*
* 20
30
18
*
27
38
44
4
*
Dimension (mm) Tolerance (mm)
10 or lower
±0.3
10 to 50
±0.5
50 or higher
±1
G9EC-1
DC Power Relays (200-A Models)
-
G
9
E
C
1
• Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
• Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
OMRON Corporation
Electronic and Mechanical Components Company
Contact: www.omron.com/ecb
Cat. No. J188-E1-02
0316(0207)(O)
5
Similar pages